D-Link Router DHP-1565 User Manual

							146
D-Link DHP-1565 User Manual
Section 5 - Connecting to a Wireless Network
5.  Type a name to identify the network.
6.  To configure advanced settings, click the         icon.
Click Next to continue.  
						

							147
D-Link DHP-1565 User Manual
Section 5 - Connecting to a Wireless Network
7.  The following window appears while the Router is being configured.
 
  Wait for the configuration to complete.
8.  The following window informs you that WPS on the DHP-1565 has been setup 
successfully.
  Make a note of the security key as you may need to provide this security key 
if adding an older wireless device to the network in the future.
9.  Click Close to complete WPS setup.  
						

							148
D-Link DHP-1565 User Manual
Section 5 - Connecting to a Wireless Network
Using Windows Vista®
Windows Vista®  users  may  use  the  built-in  wireless  utility.  If  you  are  using  another  company’s  utility  or Windows®  2000,  please  refer  to  the  user 
manual of your wireless adapter for help with connecting to a wireless network. Most utilities will have a “site survey” option similar to the Windows 
Vista®
 utility as seen below.
Right-click on the wireless computer icon in your system tray (lower -right corner 
next to the time). Select Connect to a network.
If  you  receive  the  Wireless  Networks  Detected  bubble,  click  on  the  center  of 
the bubble to access the utility.
          or
The  utility  will  display  any  available  wireless  networks  in  your  area.  Click  on  a 
network (displayed using the SSID) and click the Connect button.
If you get a good signal but cannot access the Internet, check you TCP/IP settings 
for your wireless adapter. Refer to the  Networking Basics section in this manual 
for more information.  
						

							149
D-Link DHP-1565 User Manual
Section 5 - Connecting to a Wireless Network
Configure Wireless Security
It is recommended to enable wireless security (WPA/WPA2) on your wireless router or access point before configuring your wireless adapter. If you 
are joining an existing network, you will need to know the security key or passphrase being used.
2.	 Highlight the wireless network (SSID) you would like to connect to and click 
Connect.
1. Open the Windows Vista® Wireless Utility by right-clicking on the wireless 
computer  icon  in  your  system  tray  (lower  right  corner  of  screen).  Select 
Connect to a network.   
						

							150
D-Link DHP-1565 User Manual
Section 5 - Connecting to a Wireless Network
3.  Enter the same security key or passphrase that is on your router and click  Connect.
It may take 20-30 seconds to connect to the wireless network. If the connection fails, 
please  verify  that  the  security  settings  are  correct.  The  key  or  passphrase  must  be 
exactly the same as on the wireless router.  
						

							151
D-Link DHP-1565 User Manual
Section 5 - Connecting to a Wireless Network
Using Windows® XP
Windows® XP users may use the built-in wireless utility (Zero Configuration Utility). The following instructions are for Service Pack 2 users.  If you are 
using another company’s utility or Windows® 2000, please refer to the user manual of your wireless adapter for help with connecting to a wireless 
network. Most utilities will have a “site survey” option similar to the Windows® XP utility as seen below.
Right-click on the wireless computer icon in your system tray (lower-right corner 
next to the time). Select View Available Wireless Networks.
If you receive the  Wireless Networks Detected bubble, click on the center of the 
bubble to access the utility.
          or
The  utility  will  display  any  available  wireless  networks  in  your  area.  Click  on  a 
network (displayed using the SSID) and click the Connect button.
If you get a good signal but cannot access the Internet, check you TCP/IP settings 
for your wireless adapter. Refer to the  Networking Basics section in this manual 
for more information.  
						

							152
D-Link DHP-1565 User Manual
Section 5 - Connecting to a Wireless Network
Configure WPA-PSK
It is recommended to enable WPA on your wireless router or access point before configuring your wireless adapter. If you are joining an existing 
network, you will need to know the WPA key being used.
2.	 Highlight the wireless network (SSID) you would like to connect to and 
click Connect.
1. Open the Windows® XP Wireless Utility by right-clicking on the wireless 
computer icon in your system tray (lower-right corner of screen). Select 
View Available Wireless Networks.   
						

							153
D-Link DHP-1565 User Manual
Section 5 - Connecting to a Wireless Network
3.  The  Wireless Network Connection  box will appear. Enter the WPA-PSK passphrase 
and click Connect.
It may take 20-30 seconds to connect to the wireless network. If the connection fails, 
please verify that the WPA-PSK settings are correct. The WPA-PSK passphrase must be 
exactly the same as on the wireless router.  
						

							154
D-Link DHP-1565 User Manual
Section 6 - Troubleshooting
Troubleshooting
This chapter provides solutions to problems that can occur during the installation and operation of the DHP-1565.  Read the following descriptions 
if you are having problems. The examples below are illustrated in Windows
® XP.  If you have a different operating system, the screenshots on your 
computer will look similar to the following examples.
1. Why can’t I access the web-based configuration utility?
When entering the IP address of the D-Link router (192.168.0.1 for example), you are not connecting to a website nor do you have to be connected 
to the Internet. The device has the utility built-in to a ROM chip in the device itself. Your computer must be on the same IP subnet to connect to 
the web-based utility. 
•  Make sure you have an updated Java-enabled web browser. We recommend the following: 
 
- Microsoft Internet Explorer
® 6.0 and higher
- Mozilla Firefox 3.0 and higher
- Google
™ Chrome 2.0 and higher
- Apple Safari 3.0 and higher
•  Verify physical connectivity by checking for solid link lights on the device. If you do not get a solid link light, try using a different cable or 
connect to a different port on the device if possible. If the computer is turned off, the link light may not be on.
•  Disable any Internet security software running on the computer. Software firewalls such as Zone Alarm, Black Ice, Sygate, Norton Personal 
Firewall, and Windows
® XP firewall may block access to the configuration pages. Check the help files included with your firewall software 
for more information on disabling or configuring it.  
						

							155
D-Link DHP-1565 User Manual
Section 6 - Troubleshooting
•  Configure your Internet settings:
•  Go to  Start >  Settings >  Control Panel. Double-click the  Internet Options Icon. From the  Security tab, click the button to restore 
the settings to their defaults.
•  Click the  Connection tab and set the dial-up option to Never Dial a Connection. Click the LAN Settings button. Make sure nothing 
is checked. Click OK. 
•  Go to the Advanced tab and click the button to restore these settings to their defaults. Click OK three times.
•  Close your web browser (if open) and open it.
•  Access the web management. Open your web browser and enter the IP address of your D-Link router in the address bar. This should open the 
login page for your web management. 
•  If you still cannot access the configuration, unplug the power to the router for 10 seconds and plug back in. Wait about 30 seconds and try accessing 
the configuration. If you have multiple computers, try connecting using a different computer.
2.	 What	can	I	do	if	I	forgot	my	password?
If you forgot your password, you must reset your router. Unfortunately this process will change all your settings back to the factory defaults.
To  reset  the  router,  locate  the  reset  button  (hole)  on  the  rear  panel  of  the  unit. With  the  router  powered  on,  use  a  paperclip  to  hold  the  button 
down for 5 seconds. Release the button and the router will go through its reboot process. Wait about 30 seconds to access the router. The default 
IP address is 192.168.0.1. When logging in, the username is admin and leave the password box empty.