D-Link Router DHP-1565 User Manual

							106
D-Link DHP-1565 User Manual
Section 3 - Configuration
Configuration (AP Mode)
This section will show you how to configure your new D-Link wireless router using the web-based configuration utility.
Web-based Configuration Utility
To access the configuration utility, open a web-browser such as Internet 
Explorer and enter http://dlinkrouter WXYZ (WXYZ: four-digit suffix of the 
PLC MAC address located on the botton of device) or the IP address of the 
router (192.168.0.50).
Select  Admin  in the User Name field. Leave the password blank by default. 
If  you  get  a  Page  Cannot  be  Displayed   error,  please  refer  to  the 
Troubleshooting section for assistance.
http://dlinkrouter WXYZ  
						

							107
D-Link DHP-1565 User Manual
Section 3 - Configuration
Wireless Setup Wizard
To use our web-based wizard to assist you in connecting your DHP-1565, 
click Launch Wireless Setup Wizard to begin. 
Click Next to continue your wireless network setup. 
Select one of the two configuration methods. Select  WPS if your wireless 
device support WPS and click Next to continue to the next step. 
Press down the Push Button on the wireless device within 116 seconds.   
						

							108
D-Link DHP-1565 User Manual
Section 3 - Configuration
If you would like to setup your network manually, select  Manual and click 
Next to continue. 
Enter  the  SSID  (Service  Set  Identifier).  The  SSID  is  the  name  of  your 
wireless  network.  Create  a  name  using  up  to  32  characters. The  SSID  is 
case-sensitive. Select  Assign a network key and click Next. 
Once this screen appears, the setup is complete. You will be given a detailed 
summary of your wireless security settings. 
Click Save to continue.  
						

							109
D-Link DHP-1565 User Manual
Section 3 - Configuration
Wireless Setup
Check this box to enable the wireless function. If you 
would prefer not to use wireless, uncheck the box to 
disable all the wireless functions. You may also set up a 
specific time range (schedule). Select a schedule from 
the  drop-down  menu  or  click  Add  New  Schedule  to 
create a new schedule.
W h e n   yo u   a re   b ro w s i n g   fo r   av a i l a b l e   w i re l e s s 
networks, this is the name that will appear in the list 
(unless Visibility Status is set to Invisible, see below). 
This name is also referred to as the SSID. For security 
purposes,  changing  the  default  network  name  is 
highly recommended.
Select one of the following:
802.11n  Only  -  Select  if  you  are  only  using  802.11n 
wireless clients.
Mixed 802.11n, 802.11g and 802.11b - Select if you are 
using a mix of 802.11n, 11g, and 11b wireless clients.
Mixed 802.11n, 802.11g - Select if you are only using 
802.11n, 11g wireless clients. 
The  Auto  Channel  Scan  setting  can  be  selected  to 
allow the DHP-1565 to select the channel with the least 
amount of interference (during boot-up). Indicates the 
channel setting for the DHP-1565.
The channel can be changed to fit the channel setting 
for  an  existing  wireless  network  or  to  customize  the 
wireless  network.  If  you  enable  Auto  Channel  Scan, 
this option will be grayed out.
Enable 
Wireless:
Wireless 
Network  Name:
802.11	 Mode:
Enable Auto  Channel Scan :
Wireless 
Channel  
						

							110
D-Link DHP-1565 User Manual
Section 3 - Configuration
Channel Width:
Wireless  Security 
Settings:
Save Settings: Select the Channel Width:
Auto 20/40 - Select if you are using both 802.11n and non-802.11n wireless devices.
20MHz - Select if you are not using any 802.11n wireless clients.
Locking the wireless security settings prevents the settings from being changed by any new external user using its PIN. Devices 
can still be added to the wireless network using Wi-Fi Protected Setup. It is still possible to change wireless network settings 
with Manual Wireless Network Setup, Wireless Network Setup Wizard, or an existing external WLAN Manager user. Please refer 
to page 121.
Click Save Settings to save and activate the new changes.  
						

							111
D-Link DHP-1565 User Manual
Section 3 - Configuration
Network Settings - DHCP
This section will allow you to change the local network settings of the access point and to configure the DHCP settings.
LAN 
Connection Type:
Device Name:
Save Settings: Use  the  drop-down  menu  to  select  Dynamic  IP  (DHCP) 
to automatically obtain an IP address on the LAN/private 
network.
Enter  the  Device  Name  of  the  AP.  Changing  the  Device 
Name is recommended if there is more than one D-Link 
device within the subnet.
Click 
Save Settings  to save and activate the new changes.  
						

							112
D-Link DHP-1565 User Manual
Section 3 - Configuration
Select Static IP to manually enter the IP address, subnet mask, and default gateway addresses.
LAN Connection  Type:
IP Address:
Subnet Mask: Default 
Gateway:
Device Name:
Save Settings: Select Static IP from the drop-down menu.
Enter  the  IP  address  of  the  access  point.  The  default  IP 
address  is  192.168.0.1.  If  you  change  the  IP  address,  once 
you click Apply, you will need to enter the new IP address 
in your browser to return to the configuration utility.
Enter the Subnet Mask.
Enter  the  Gateway.  This  is  usually  the  LAN  or  internal  IP 
address of your router.
Enter the Device Name of the AP. It is recommended that you 
change the Device Name if there is more than one D-Link 
device  within  the  subnet. You  can  enter  the  device  name 
of the AP into your web browser to access it instead of IP 
address for configuration. If you are using the device name 
to connect, make sure that your PC and your DHP-1565 are 
on the same network.
Click Save Settings to save and activate the new changes.
Network Setup - Static IP  
						

							113
D-Link DHP-1565 User Manual
Section 3 - Configuration
My IPv6 
Connection is:
LAN IPv6 Address  settings: Select Link-local only from the drop-down menu. 
This section displays the IPv6 address of the router.
My IPv6 
Connection is:
LAN IPv6 Address: Select static IPv6 from the drop-down menu.
Enter the LAN (local) IPv6 address for the router.   
						

							114
D-Link DHP-1565 User Manual
Section 3 - Configuration
My IPv6 
Connection:
IPv6 DNS Settings: Select 
Autoconfiguration  (Stateless/DHCPv6)   from 
the drop down menu. 
Select  Obtain IPv6 DNS Server automatically or enter 
a specific DNS Server address.   
						

							115
D-Link DHP-1565 User Manual
Section 3 - Configuration
Configuration
This section will show you how to configure your new D-Link PowerLine AV using the web-based configuration utility.
PLC Settings - AP Mode