D-Link Router DHP-1565 User Manual

							16
D-Link DHP-1565 User Manual
Section 1 - Product Overview
PowerLine Security
It is strongly recommended to encrypt your PowerLine network. By encrypting the data that is sent via your PowerLine adapters, you will prevent 
nearby hackers with a Powerline adapter to connect to your network and steal your information.
To encrypt your PowerLine network, follow the steps below:
PowerLine Network-Quick Setup
The  Common  Connect  Button  is  used  to  add  a  PowerLine  AV  device  to  a  PowerLine  network. You  can  allow  the  DHP-1565  to  join  a  network  by 
pressing the Common Connect Button to toggle it to the Broadcast state or Join state.
The Common Connect Button has 3 different trigger states:
  Broadcast state-  Enables the DHP-1565 to provide information for another PowerLine AV device to join its PowerLine network (works 
even  if  it  is  the  only  device  existing  within  the  network  group). The  first  PowerLine  device  will  use  this  state  when  the  Common 
Connect Button is pressed. 
  Join State - This allows an ungrouped PowerLine AV device to join an existing PowerLine network. PowerLine devices added after 
the first device will be in the Join State when the Common Connect Button is pressed.
  Ungroup State -  Hold down the Common Connect Button for more than 10 seconds to detach the device from its network group. 
Encryption Button Usage  
						

							17
D-Link DHP-1565 User Manual
Section 1 - Product Overview
Note: A minimum of two PowerLine AV devices are required to create a network in order for your product to work properly.
Step 1
Plug  the  other  PowerLine  AV  devices  in  the  same  room  to  verify  if  your  home’s  electrical  wiring  is  suitable  for  the  PowerLine  Network.  Once 
configured you may place your PowerLine AV devices in the location of your choice. Plug one end of the Ethernet cable into the Ethernet port on 
the PowerLine AV device. 
Step 2
Press the  Common Connect Button       located on the back panel of the DHP-1565 for 1 to 3 seconds. The Power LED          will start blinking after 
you release the button. Within 2 minutes of pushing the  Common Connect Button on the DHP-1565, press the Common Connect Button          on 
the second PowerLine AV device(s) in your existing PowerLine network for 1 to 3 seconds. The Power LED         will start blinking after you release the 
button. Network Connectivity is confirmed when the PowerLine LEDs          indicators on the DHP-1565 and PowerLine AV device are illuminated. 
Step 3
After  the  network  security  setup  steps,  your  PowerLine  network  will  be  securely  configured  with  the  same  network  encryption  key.  Place  any 
additional PowerLine AV devices in a different area of your home. The PowerLine AV devices will save the security settings even if they are unplugged.
Step 4
If your network has more than two PowerLine AV devices, press the  Common Connect Button       on the DHP-1565 for 1 to 3 seconds. Within 2 
minutes of pushing the  Common Connect Button on the DHP-1565, press the  Common Connect Button on any additional PowerLine AV devices 
in your existing PowerLine network for 1 to 3 seconds. 
Network Connectivity is confirmed when the PowerLine LEDs indicators       on the DHP-1565 and PowerLine AV device are illuminated. After the 
network security setup steps, you can place any additional PowerLine AV devices in a different area of your home. The PowerLine AV devices will 
save the security settings even if they are unplugged.
PowerLine Network Device Setup  
						

							18
D-Link DHP-1565 User Manual
Section 2 - Installation
The DHP-1565 includes Setup Wizard CD. Follow the simple steps below to run the Setup Wizard to guide you quickly through 
the installation process. 
Insert the  Setup Wizard CD  in the CD-ROM drive. The step-by-step instructions that follow are shown in Windows® XP. The steps and screens are 
similar for the other Windows operating systems.
If  the  CD  Autorun  function  does  not  automatically  start  on  your  computer,  go  to  Start  > Run.  In  the  run  box  type“D:\autorun.exe”  (where  D: 
represents the drive letter of your CD-ROM drive).
When the autorun screen appears, click  Start.
Getting Started  
						

							19
D-Link DHP-1565 User Manual
Section 3 - Configuration
Configuration (Router Mode)
This section will show you how to configure your new D-Link wireless router using the web-based configuration utility.
Web-based Configuration Utility
To access the configuration utility, open a web-browser such as Internet 
Explorer  and  enter  http://dlinkrouter  or  the  IP  address  of  the  router 
(192.168.0.1).
Select  Admin  in the User Name field. Leave the password blank by default. 
If  you  get  a  Page  Cannot  be  Displayed   error,  please  refer  to  the 
Troubleshooting section for assistance.
http://dlinkrouter  
						

							20
D-Link DHP-1565 User Manual
Section 3 - Configuration
Internet
Setup
This section allows you to configure your Router’s Internet settings.
The  Internet  Connection  Setup  Wizard  provides  a  quick 
method  for  configuring  your  Internet  settings.  To  start 
the Internet Connection Setup Wizard, click the  Internet 
Connection  Setup  Wizard   button.  Refer  to  “Internet 
Connection Setup Wizard” on page 21 for more information 
on how to use the Internet Connection Setup Wizard.
Click  the  Manual  Internet  Connection  Setup  button  if 
you want to enter your Internet settings without running 
the  Internet  Connection  Setup Wizard.  Refer  to “Manual 
Internet Connection Setup” on page 27 for more information 
on how to configure your Internet settings manually.
Internet 
Connection 
Setup Wizard:
Manual 
Internet 
Connection  Option:  
						

							21
D-Link DHP-1565 User Manual
Section 3 - Configuration
Internet Connection Setup Wizard
Click the  Internet Connection Setup Wizard button to start the Internet 
Connection Setup Wizard.  
						

							22
D-Link DHP-1565 User Manual
Section 3 - Configuration
Create a new password and then click Next to continue.
The  following  window  appears,  summarizing  the  steps  required  to 
complete the Internet Connection Setup Wizard:
Click Next to continue.
Select your time zone from the drop-down menu and then click  Next to 
continue.  
						

							23
D-Link DHP-1565 User Manual
Section 3 - Configuration
Select  the  type  of  Internet  connection  you  use  and  then  click  Next  to 
continue.
If you selected  DHCP Connection (Dynamic IP Address) , you may need to 
enter the MAC address of the computer that was last connected directly 
to your modem. If you are currently using that computer, click  Clone Your 
PC’s MAC Address and then click Next to continue.
The Host Name is optional but may be required by some ISPs. The default 
host name is the device name of the router and may be changed.  
						

							24
D-Link DHP-1565 User Manual
Section 3 - Configuration
If you selected PPPoE, enter your PPPoE username and password. 
If your ISP requires you to enter a PPPoE service name, enter the service 
name in the Service Name field.
Select  Static if your ISP assigned you the IP address, subnet mask, gateway, 
and DNS server addresses.
Click Next to continue.
Note:  Make  sure  to  remove  your  PPPoE  software  from  your  computer.  The 
software is no longer needed and will not work through a router.
If you selected PPTP, enter your PPTP username and password. 
Select  Static if your ISP assigned you the IP address, subnet mask, gateway, 
and PPTP server addresses.
Click Next to continue.  
						

							25
D-Link DHP-1565 User Manual
Section 3 - Configuration
If you selected L2TP, enter your L2TP username and password. 
Select  Static if your ISP assigned you the IP address, subnet mask, gateway, 
and L2TP server addresses.
Click Next to continue.
If you selected  Static, enter your network settings supplied by your Internet 
provider. 
Click Next to continue.