D-Link Router DHP-1565 User Manual

56
D-Link DHP-1565 User Manual
Section 3 - Configuration
IPv6 in IPv4 Tunneling
Select IPv6 in IPv4 Tunnel from the drop-down menu.
Enter the settings supplied by your Internet provider (ISP). 
Enter the LAN (local) IPv6 address for the router. 
Displays the Router’s LAN Link-Local Address.
Check to enable the Autoconfiguration feature.
Select Stateful (DHCPv6), SLAAC + RDNSS or SLAAC + Stateless DHCPv6. 
Enter the start IPv6 Address for the DHCPv6 range for your local computers.
Enter the end IPv6...

57
D-Link DHP-1565 User Manual
Section 3 - Configuration
6 to 4 Tunneling
Select 6 to 4 from the drop-down menu.
Enter the IPv6 settings supplied by your Internet provider (ISP). 
Enter the primary and secondary DNS server addresses. 
Enter the LAN (local) IPv6 address for the router. 
Displays the Router’s LAN Link-Local Address.
Check to enable the Autoconfiguration feature.
Select Stateful (DHCPv6), SLAAC + RDNSS or SLAAC + Stateless DHCPv6. 
Enter the start IPv6 Address for the DHCPv6 range for your...

58
D-Link DHP-1565 User Manual
Section 3 - Configuration
6rd
Select 6rd from the drop-down menu.
Enter the address settings supplied by your Internet provider (ISP). 
Enter the LAN (local) IPv6 address for the router. 
Displays the Router’s LAN Link-Local Address.
Check to enable the Autoconfiguration feature.
Select Stateful	(DHCPv6),	SLAAC+RDNSS	or	SLAAC	+	Stateless	DHCPv6.	
Enter the Router Advertisement Lifetime (in minutes).
My IPv6 Connection:
6RD Settings:
LAN IPv6 Address:
LAN Link-Local...

59
D-Link DHP-1565 User Manual
Section 3 - Configuration
This section will show you how to configure your new D-Link PowerLine AV using the web-based configuration utility.
PLC Settings (Router Mode)  

60
D-Link DHP-1565 User Manual
Section 3 - Configuration
Network 
Name:
Public 
Network  Name:
Private 
Network  Name:
Scan:
Add Member:
Device Name: Password: You  can  set  the  name  of  your  network  and  to  make  it 
either public or private. Make sure the Network Name of 
all  of  the  devices  within  your  PowerLine  network  is  the 
same.
Select this option if you would like to make your powerline 
network  public  with  the  default  Network  Name  of 
“HomePlugAV”.  Since  this  is  a...

61
D-Link DHP-1565 User Manual
Section 3 - Configuration
Member List:
Link Rate: This  section  provides  information  on  the  PowerLine 
AV  devices  in  your  PowerLine  network,  or  any  devices 
that  were  previously  connected  but  it  are  currently 
disconnected.
Displays the device’s current data rate in Mbps. 
Status:
Qos Settings:
Mac Address: This  field  shows  the  status  of  the  device.  If  the  field 
displays the word Connect, then the device is connected 
to your PowerLine...

62
D-Link DHP-1565 User Manual
Section 3 - Configuration
The DHP-1565 can be configured as a virtual server so that remote users accessing Web or FTP services via the public IP address can be automatically 
redirected to local servers in the LAN (Local Area Network). 
The  DHP-1565  firewall  feature  filters  out  unrecognized  packets  to  protect  your  LAN  network  so  all  computers  networked  with  the  DHP-1565 
are invisible to the outside world. If you wish, you can make some of the LAN...

63
D-Link DHP-1565 User Manual
Section 3 - Configuration
The Virtual Server window allows you to open a single port. If you would like to open a range of ports, refer to the next page.
Check  the  box  on  the  left  side  to  enable  the  Virtual 
Server rule.
Enter a name for the rule or select an application from 
the drop-down menu. Select an application and click 

64
D-Link DHP-1565 User Manual
Section 3 - Configuration
This will allow you to open a single port or a range of ports.
Port Forwarding
Tick the checkbox on the left side to enable the Port 
Forwarding rule.
Enter  a  name  for  the  rule  or  select  an  application 
from  the  drop-down  menu.  Select  an  application 
and click 

65
D-Link DHP-1565 User Manual
Section 3 - Configuration
Check the box on the left side to enable the Application 
Rule.
Enter  a  name  for  the  rule. You  may  select  a  pre-defined 
application  from  the  Application  drop-down  menu  and 
click