D-Link Router DHP-1565 User Manual

26
D-Link DHP-1565 User Manual
Section 3 - Configuration
Click Connect to save your settings. 
 
The  following  window  appears  to  indicate  that  the  settings  are  being 
saved. When the Router has finished saving all the changes, the  Setup> 
Internet window will open.
Close your browser window and reopen it to test your Internet connection. 
It may take a few tries to initially connect to the Internet.  

27
D-Link DHP-1565 User Manual
Section 3 - Configuration
Manual Internet Connection Setup
Use  the  My  Internet  Connection  is  drop-down  menu  to 
select the mode that the router should use to connect to 
the Internet.
Advanced Domain Name System (DNS) Services enhances 
your Internet performance by getting you the information 
and web pages you are looking for faster and more reliably. 
In  addition,  it  improves  your  overall  Internet  experience 
by correcting many common typo mistakes...

28
D-Link DHP-1565 User Manual
Section 3 - Configuration
Enter the IP address assigned by your ISP.
Enter the Subnet Mask assigned by your ISP.
Enter the Gateway assigned by your ISP.
The  DNS  server  information  will  be  supplied  by  your  ISP 
(Internet Service Provider).
Maximum Transmission Unit - you may need to change the 
MTU for optimal performance with your specific ISP. 1500 
is the default MTU.
The  default  MAC  Address  is  set  to  the  Internet  port’s 
physical interface MAC address...

29
D-Link DHP-1565 User Manual
Section 3 - Configuration
The  Host  Name  is  optional  but  may  be  required  by  some 
ISPs. Leave blank if you are not sure.
Enter the Primary and Secondary DNS server IP addresses 
assigned by your ISP. These addresses are usually obtained 
automatically  from  your  ISP.  Enter  the  value  0.0.0.0  if  you 
did not specifically receive these from your ISP.
Maximum Transmission Unit - you may need to change the 
MTU for optimal performance with your specific ISP....

30
D-Link DHP-1565 User Manual
Section 3 - Configuration
Select  Static  IP  if  your  ISP  assigned  you  the  IP  address, 
subnet mask, gateway, and DNS server addresses. In most 
cases, select Dynamic.
Enter the IP address (Static PPPoE only).
Enter your PPPoE user name.
Enter your PPPoE password and then retype the password 
in the next box.
Enter the ISP Service Name (optional).
Use  the  radio  buttons  to  specify  the  reconnect  mode. 
The  user can specify a custom schedule or specify the  On...

31
D-Link DHP-1565 User Manual
Section 3 - Configuration
The default MAC Address is set to the Internet port’s physical interface MAC address on the Broadband Router. It is not recommended 
that  you  change  the  default  MAC  address  unless  required  by  your  ISP.   You  can  use  the  Clone Your  PC’s  MAC  Address  button  to 
replace the Internet port’s MAC address with the MAC address of your Ethernet card.
MAC Address:
Click the Save Settings button to save any changes made.  

32
D-Link DHP-1565 User Manual
Section 3 - Configuration
Select Static  IP   if  your  ISP  assigned  you  the  IP  address,  subnet 
mask,  gateway,  and  DNS  server  addresses.  In  most  cases,  select 
Dynamic IP.
Enter the IP address (Static PPTP only).
Enter  the  Primary  and  Secondary  DNS  Server  Addresses  (Static 
PPTP only).
Enter the Gateway IP Address provided by your ISP.
Enter the Server IP provided by your ISP (optional).
Enter your PPTP username.
Enter  your  PPTP  password  and...

33
D-Link DHP-1565 User Manual
Section 3 - Configuration
The DNS server information will be supplied by your ISP (Internet Service Provider).
Maximum Transmission Unit - you may need to change the MTU for optimal performance with your specific ISP. 1454 is the default 
MTU.
The default MAC Address is set to the Internet port’s physical interface MAC address on the Broadband Router. It is not recommended 
that you change the default MAC address unless required by your ISP.  You can use the  Clone Your...

34
D-Link DHP-1565 User Manual
Section 3 - Configuration
Select  Static  if  your  ISP  assigned  you  the  IP  address,  subnet 
mask,  gateway,  and  DNS  server  addresses.  In  most  cases, 
select Dynamic.
Enter the L2TP IP address supplied by your ISP (Static only).
Enter the Subnet Mask supplied by your ISP (Static only).
Enter the Gateway IP Address provided by your ISP.
Enter the Server IP provided by your ISP (optional).
Enter your L2TP username.
Enter  your  L2TP  password  and  then  retype...

35
D-Link DHP-1565 User Manual
Section 3 - Configuration
Primary DNS  Server:
MTU:
MAC Address: Enter the Primary DNS server IP address assigned by your ISP. These address is usually obtained automatically from your ISP. Enter 
the value 0.0.0.0 if you did not specifically receive these from your ISP.
Maximum Transmission Unit - you may need to change the MTU for optimal performance with your specific ISP. 1454 is the default 
MTU.
The default MAC Address is set to the Internet port’s physical interface...