D-Link Dsh8 Manual

 Chapter 5: Web-Based Management 
GE-DSH-73/DSH-82 and DSH-82-PoE User Manual  57 
Object Description 
Authentication:  Having ticked this checkbox, 
the mail account, password and 
confirm password column fields will then show up. Configure the 
email account and password for authentication when this switch 
logs in to the SMTP server. 
Mail Account:  Set up the email account, e.g. jack, to receive the email alert. It must 
be an existing email account on the mail server. 
Password:  Type in the...

Chapter 5: Web-Based Management 
58  GE-DSH-73/DSH-82 and DSH-82-PoE User Manual 
This page includes the following fields: 
 
Object Description 
System event selection: There are 4 event types—Device Cold Start, Device Warm Start, 
Authentication Failure, and X-ring Topology Change. The 
checkboxes are not available for ticking unless the Syslog Client 
Mode on the Syslog Configuration tab and the E-mail Alert on the 
SMTP Configuration tab are enabled first. 
Device cold start: When the device...

 Chapter 5: Web-Based Management 
GE-DSH-73/DSH-82 and DSH-82-PoE User Manual  59 
Fault Relay Alarm 
The Fault Relay Alarm function provides th e Power Failure and Port Link Down/Broken 
detection. With both power input 1 and po wer input 2 installed and the check boxes 
of power 1/power 2 ticked, the FAULT LED indi cator will then be possible to light up 
when any one of the power failures occu rs. As for the Port Link Down/Broken 
detection, the FAULT LED indicator will light up  when the port...

Chapter 5: Web-Based Management 
60  GE-DSH-73/DSH-82 and DSH-82-PoE User Manual 
SNTP Configuration 
SNTP (Simple Network Time Protocol) is a simplified version of NTP, which is an 
Internet protocol used to synchronize  the clocks of computers to some time 
reference. Because time usually just advances,  the time on different node stations will 
be different. With the communicating progra ms running on those devices, it would 
cause time to jump forward and back, a no n-desirable effect. Therefore,...

 Chapter 5: Web-Based Management 
GE-DSH-73/DSH-82 and DSH-82-PoE User Manual  61 
UTC Timezone:  Universal Time, Coordinated. Set the switch location time zone. The 
following table lists the different location time zone for your reference. 
SNTP Sever URL: Set the SNTP server IP address. You can assign a local network time 
server IP address or an internet time server IP address. 
Switch Timer: When the switch has successfully connected to the SNTP server whose 
IP address was assigned in the column...

Chapter 5: Web-Based Management 
62  GE-DSH-73/DSH-82 and DSH-82-PoE User Manual 
 
Local Time Zone Conversion from UTC  Time at 12:00 UTC 
November Time Zone - 1 hour  11am 
Oscar Time Zone -2 hours  10 am 
ADT - Atlantic Daylight  -3 hours  9 am 
AST - Atlantic Standard 
EDT - Eastern Daylight  -4 hours  8 am 
EST - Eastern Standard 
CDT - Central Daylight  -5 hours  7 am 
CST - Central Standard 
MDT - Mountain Daylight  -6 hours  6 am 
MST - Mountain Standard 
PDT - Pacific Daylight  -7 hours  5 am...

 Chapter 5: Web-Based Management 
GE-DSH-73/DSH-82 and DSH-82-PoE User Manual  63 
Local Time Zone Conversion from UTC   Time at 12:00 UTC 
CCT - China Coast, USSR Zone 7  +8 hours  8 pm 
JST - Japan Standard, USSR Zone 8  +9 hours  9 pm 
EAST - East Australian Standard GST 
Guam Standard, USSR Zone 9   +10 hours  10 pm 
IDLE - International Date Line  
NZST - New Zealand Standard  
NZT - New Zealand   
+12 hours  Midnight 
 
IP Security 
IP security function allows  the user to assign 10 specific IP...

Chapter 5: Web-Based Management 
64  GE-DSH-73/DSH-82 and DSH-82-PoE User Manual 
This page includes the following fields: 
 
Object Description 
IP Security Mode: Having set this selection item in the Enable mode, the Enable HTTP 
Server, Enable Telnet Server checkboxes and the ten security IP column 
fields will then be available. If not, those items will appear in grey. 
Enable HTTP Server: Having ticked this checkbox, the devices whose IP addresses match 
any one of the ten IP addresses in the...

 Chapter 5: Web-Based Management 
GE-DSH-73/DSH-82 and DSH-82-PoE User Manual  65 
This page includes the following fields: 
 
Object Description 
User name:  Type in the new user name  
The default user name is ‘admin’ 
Password: Type in the new password  
The default is ‘admin’ 
Confirm password:  Re-type the new password 
Port Management 
Port Statistics 
The following chart provides the current stat
istic information, which displays the real-
time packet transfer status for each port.  The user...

Chapter 5: Web-Based Management 
66  GE-DSH-73/DSH-82 and DSH-82-PoE User Manual 
This page includes the following fields: 
 
Object Description 
Port:  The port number. 
Type:  Displays the current speed of connection to the port. 
Link:  The status of linking—‘Up’ or ‘Down’. 
State: It’s set by Port Control. When the state is disabled, the port will not 
transmit or receive any packet. 
Tx Good Packet:  The counts of transmitting good packets via this port. 
Tx Bad Packet: The counts of transmitting...