Comdial Impact Dsu Instructions Manual

3.7.12 Flexible Ringing Assignments
You can enable different ringing assignments for individual lines and stations.
Direct/Delayed Ringing
Description:You must program ringing assignments on a per station/per line basis. You can control
ringing for every line that has appearance at a station assigning immediate, or direct,
ringing to some lines and delayed ringing to others.
NOTE:Do not program direct ringing for lines that you assign to the direct
department calling feature.
To Program:1....

Night Transfer (Of Ringing)—Line/Station Assignments
Description:You or the system attendant can place the system into the night transfer (of ringing) mode
of operation. While in this mode of operation, the system will activate special line/station
ringing assignments. Use this procedure to program these assignments.
To Program:1. Dial54.“STA/LINE CONFIG”
2. Dial3.“NIGHT RING”
3. Select line ports for night ringing (LED On = Selected Ports)
—Line port 1–14 = Dial01–14or pressA1–A14
—Line port 15, 16 =...

Delayed Ringing Times
Description:You assign delayed ringing to stations for specific lines, you can also set the time length
of the delay.
To Program:1. Dial17.“SYSTEM FEATURES ”
2. Dial05.“DELAY RING XX”
3. Select delay time (LED On = Selected Time)
—Dial1or pressA1= 6 seconds“DELAY RING 6”
—Dial2or pressA2= 12 seconds“DELAY RING 12”
—Dial3or pressA3= 18 seconds“DELAY RING 18”
—Dial4or pressA4= 24 seconds“DELAY RING 24”
—Dial5or pressA5= 30 seconds“DELAY RING 30”
—Dial6or pressA8= 36 seconds“DELAY RING...

3.7.13 Flexible Station Numbering
Description:The system supports a flexible station numbering plan for calling individual stations and
departments. You can program each station port to respond to the dialing of any available
number between 10 and 7999; however, the system will not allow you to assign the same
dialing code as both a station extension number and a department access code, nor will
the system allow you to assign an extension number or access code conflict such as 15
and 1500.
To Program:1....

3.7.15 Handset Volume Control On Impact Telephones
Description:Impacttelephones have 8 handset volume settings at default. You may increase the
number of volume settings to 13 on an individual station basis.
To Program:1. Dial53.“STATION FEATURES”
2. Dial38.“HANDSET VOLUME”
3. Select station ports (LED on = Feature Assigned):
—Station 10–57: Dial10–57or pressC10–C57.
4. DialSfor next station feature
—OR—
dialSSfor configuration mode.
To change setting, repeat procedure and make different selection....

3.7.16 Headset Interface
You can program LCD speakerphones equipped with the optional headset jack to use a headset as well as
the handset or speakerphone.
NOTE:The system delivers subdued off-hook voice announcements (SOHVA) to the headset.
Because a headset exhibits a coupling effect between the earpiece and microphone, it may
allow the outside party to hear a SOHVA message. You should inform the user of this
possibility.
Headset Operation As A Class Of service
Description:When employing DigiTech...

3.7.17 Interactive Buttons
Description:The digital telephone system supports the operation of interactive buttons on all currently
produced Comdial proprietary LCD speakerphones. Interactive buttons provide users
with quick, easy access to system features and an expanded display that prompts them on
feature operation and progress. DigiTech andImpactLCD speakerphones provide
interactive buttons to the user at all times; however, the DigiTech LCD speakerphones
(revision H and earlier) do not provide...

3.7.18 Idle Line Preference
Description:When you enable idle line preference, a station will automatically connect to any
assigned and idle line that you have programmed for this purpose when the user takes the
station off hook.
To Program:1. Dial54.“STA/LINE CONFIG.”
2. Dial7.“IDLE LINE PREF.”
3. Select line ports (LED On = Selected Port)
—Line port 1–14 = Dial01–14or pressA1–A14
—Line port 15, 16 = Dial15, 16or pressB1, B2
—Line port 17–24 = Dial17–24or press HOLD then pressA1–A8.
4. Dial # when all...

3.7.19 Personal Ringing Tones
Description:You can program stations to ring in one of six distinctive tones:
1. 666/571 Hz @ 16 Hz warble
2. 1000/800 Hz @ 16 Hz warble
3. 666/571 Hz @ 23 Hz warble
4. 1000/800 Hz @ 23 Hz warble
5. 500/444 Hz @ 16 Hz warble
6. 500/444 Hz @ 23 Hz warble
To Program:1. Dial53.“STATION FEATURES”
2. Dial14.“RINGING TONE”
3. Select ringing tone
—Dial1for tone 1“RINGING TONE 1”
—Dial2for tone 2“RINGING TONE 2”
—Dial3for tone 3“RINGING TONE 3”
—Dial4for tone 4“RINGING TONE 4”...

3.7.20 Prime Line, Prime Group, And Prime Intercom
Description:If you assign a group of lines, an intercom line, or one individual line to a particular
station for use as its prime line, the station automatically selects it for use when the user
takes it off-hook.
To Program:1. Dial53.“STATION FEATURES”
2. Dial15.“PRIME LINE ”
3a. Assign prime line“PRIME LINE XX”
—Line port 1–14 = Dial01–14or pressA1–A14
—Line port 15, 16 = Dial15,16or pressB1,B2
—Line port 17–24 = Dial17–24or pressHOLDthen pressA1–A8....