Comdial Executech Model 0616x, 0816x Electronic Key Systems Instructions Manual

							IMI 66-031System Programming
SMDR ANP COS PRINTOUT
SMDR PRINTOUT
A data printer can be connected to the system to be
used for printing station message detail recording
(SMDR) information. The SMDR data is provided
automatically as it is generated. No intervention is
required to obtain the printout. The data is for-
matted as shown in Figure 3-2. Either an 80
column or a 
40-column printout line can be
selected through the system COS programming.
COS PRINTOUT
When a data printer is connected to the system to be
used for printing SMDR data, it can be commanded
from station 10 to also print a record of the current
COS configuration. Partial or complete printouts can
be obtained. When the printer is being used to obtain
a COS printout, the SMDR printout is temporarily
halted; however, SMDR data collection is continued
by the system during a COS printout operation. If
more than two calls are logged for any one tine
during the halt, call records may be lost. Typical COS
printouts are shown in Figure 3-3.To obtain the COS printout,l
Press ITCM * 7 4 6 +% (base level if not active)
PRINT SYSTEM AND LINE COS PLUS TOLL RESTRICTIONSl
Press memory key to select type of printout desired.
The COS printout will begin immediately.
To abort printout,l
Press memory key A9.
To exit COS 
prfntout mode,l
Press f MONITOR.
- -- -----3-8 
						

							STATION NUMBER
40 COLUMN
PRINTOUT
LINES
1T [CARRIAGE RETURN! (LlNEj
2X &ARRlAGE FE~URN 1 I--,I-
MONTH/DAY/YEARINITIATE TIME-HOUR : MINUTE
(24 HOUR REAL TIME CLOCK)
\J
DIALED DIGITS-UP TO MAXIMUM OF 32
(ACCOUNT CODES ARE ISOLATED BY l OR # SYMBOLS
NOTES
1. CARRIAGE RETURN AND LINE FEED IMMEDIATELY
;O$.OW LAST PRINTED CHARACTER ON EACH
9782200
OUTGOING CALL24 2 
12/05/06 17:Ol.5
(WITH ACCOUNT CODES)1~~33456789’0#‘7412580#9831’w
AC POWER FAILURE AND
RESTORATION
2FFTlME l * 12/05/8617:03.;. 12/05/06 17:08
Flgure 3-2. Station Message Detail Record Prlntout Format 
						

							IMi 66-031System Programming
SYSTEM COSTOLL RESTRICTION TABLES
PAUSE TIRE2.0 SECPULSE DIAL 20 PPS
FLASH TIME720 MSECHOLD RECALL 240 SEC
TABLE1DENY11
2 0
3 
-4
LINE 
COSLINE PRV TYPE PU- HOLD TOLL
RLSLSE.SOMS TABLESTABLE 2 ALLOW
1 17034344664
2 17039493113
3 1985
4 1831
1C.O.2C.O.3C.O.4 xc-0.5 x
AUX
6NONE7PABX x
8 XPABX x
STATION 13
TOLL RESTRICTION
P.A. ENABLE
PRIME 
LINE123 6
123 6
123 6
123 6
78X
456X456
123
1
LINE12345678
RING X
DELAY RING X
NITE RING
ACCESS DENY
ORIGIN DENYPRIVACY 
RLS
ALL CALL
RECEIVE
ORIGIN
GROUPABCD
ABCD
X
X
BUTTON12345678LINE NO.2 3 4 1 6 7 8 5TABLE3 
DENY1 8313
2 5891
34TABLE 4 DENY
1 91
2 90
:TABLE 5 ALLOW
1 91804
2 917034341133
3 
91703494?7??
4TABLE6 ALLOW
1 1800
2 91800
:TABLE 7 DENY
11
2 2
3 3
4 91985
TABLE 8 ALLOW
14
2 5
3 6
4 17039491234
Figure 3-3. Typical COS Printout
(Model 0616X Shown. Model 0616X same except six 
lines)
3-10 
						

							IMI 66-031System Programming
SYSTEM CLOCK INFORMATION
SElTlNG THE CLOCK
1.Press ITCM, then dial +# #.
2.Dial clock date with keypad keys.l
Values less than 10 must be dialed asox.
l
Hours must be expressed in 24-hour for-
mat..
Enter: YEAR MONTH DAY HOURMINUTE
Example: 8808061530 (August 6,1988,3:30 PM)
3.If SMDR printer is installed and operating, clock
date will be printed as illustrated in following typi-
cal example:
W 01/08/86 16:00
4.Reset minutes setting, if necessary, as follows:l
Repeat step 1.l
Dial new digits, and press #.l
A new clock date printing will occur.
CHECKING THE TIME SETTING
A printing of the current clock date can be obtained
from station 10 whenever needed as follows:l
Press ITCM and dial * # #.A clock date printing will automatically occur once
each 24-hour period. This daily, automatic printing
will formatted as follows:
W MO/DY/YR 0O:OO (current date and 0O:OO hours)POWER 
INTERRUPTIoN
The system clock will continue to run for at least 30
minutes after AC power has been removed form the
system. If power is restored within the 
30-minute
backup period, the 
following.printing sequence will
occur:
OFF 
TIME +I& MOlDY/YR iiR:Mti
(time of power outage)
+#+ MOlDY/YR HR:MN(time of poker return)
If power is not restored within the backup period, the
following printing sequence will occur when the
power is restored.
CLOCK 
NOT VALID
++G% 12/01/86 0O:OO(default clock date)
The clock will begin running from the default date. It
must be reset to the current date per the instructions
above.
:
3-l 1 
						

							IMI 66-031
SYSTEM SPEED DIAL PROGRAMMING
System Programming
Ten (10) system speed dial numbers can be stored
from station 10 for use at all stations in the system.
To store speed dial numbers,To end procedure,l Press MONITOR
l Press 
ITCMt. .
l
Perform the following steps:l Press SAVE.
l
Dial storage location (1-O) from keypad.
Press line select key (program keys 
Bl-S6)l
SYSTEM SPEED DIAL INDEX
(enter programmed numbers)
1
2
to identify line to be preselected during opera-3
tion (otherwise system will pick prime line or
last line used).4
*Dial speed dial number from keypad (up to31 digits). .‘.5
-Dial 1 - 0, #, and +K as required.6l
Press HOLD to store pause if required.
7
-Press RECALL to store flash if required.
Repeat the preceding steps for each number8-
to be stored.9
2
3-12 
						

							IMI66-031System Programming
Table 
3-l. System COS Programming Reference
PROCEDURE
Note: Circle the record values at right
before performing the procedure given below.
1. BASE LEVEL ENTRY.PressfTCM*746+
2PULSWONE OR TONE ONLY DIALING MODE. Presst.
Press 0 for tone dialing.Press 
1% pulse/tone dialing
.
Press*
3.FIRST ATEMPTED INTERCOM SIGNALING MODEPress Al3 for tone signalling .
.Press Al4 for voice signalling
.Press*
4. TIME MERVAL FOR PROGRAMMED PAUSE.Press4
.Press one key
KEY 1 1 1 2 1 3 1 4 1 5 1 6 1 7 1 8 
I 9 I 0SEC. 
~0.5~1.0)1.5~2.0(3.0)5.0~7.5~1o.~15.~2o.
RECORD
(Shading Denotes Default Value)
Note: Circle the desired value
for the system being programmed.
I;=11.:‘:~~~~~~-gPULSE/TONE SWITCHABLEI
~~~~~&~~~~-gg@$@!J .._._._... ._. . . . . . . . . . :. . . . _ . . ..: :.. 1
TONE SIGNALLINGSECONDS
0.5 
p;g$ 1.5 1 2.0 1 3.0 5.0 7.5 10. 15. 120..Press 
Y
5.PULSE DlAL CHARACTERISTICS - PPI AND MAKE/BREAK.Press5
.Press 
1= 10 PPI and 60140.Press 
2y20 PPI and 60140.
Press*
6. HOOKSWITCH FIASHIRECALLTIME INTERVAL.Press6
KEY 
I 1 1 2~3~4~5~6~7~8~9~ 0
SEC. 
I -08 -30 .50 .60 .75 .875 1.0 1.5 2.0 3.0
.Press one key:
.Press*
7. HOLD RECALL TIME INTERVAL.Press7
.Press one key:
KEY 1 1 
( 2 1 3 ) 4 I 5 I 6 I 7 1 8 ( 9 I 0
SEC. 30 80 90 120 180 240 300 360 420 
noneSECONDS
90 1120118012401300 
360142O(nona.Press 
t
3-13 
						

							1MI 66-031System Programming
0. TOLL RESTRICTION RtQlhMtNTS.
Set system toll restriction requirements per instructions
given on Table 3-4Record 
all toll restricbn data on table 3-4.
9. SMDR DATA SPEED BAUD RATE. 
Press3=3oDbaud.
Press OZlO baudI. Press1 
=7!5Omsec..
Press ,fl-2 sec.
No&: If a timeout occurs during the program-
ming sequence, 
perform base level entry again
and proceed at any program step. 
						

							IMI 66-031System Programming
Table 3-2. 
Line COS Programmlng Reference
PROCEDURE
NUltEnter the information In the box at right before
performing the pfugram pfucadwes givan below
1. BASE LEVELENTRY.Press ITCM * 746 S2 PRNACY STATLJS.
Press 6. All line6 private.
Press keys for non-private..(Bl-86 for model 0616x). (B1-86formodelO616X). Press*
3. SELECT LINE FOR PROGRAMMING.
Press 81-88 (model 0816X).
Press BTi6 (model 0616X)4. SPECIFY LINE TYPE. 
Pressby: O=Disabledl.he
1 = Auxiliary Line
2=COtine
3=PBXLine5.ASSIGN TOLL TABLES TO LINE. Press memory keys:
Al-A8 = Tables l-8
6. DIALING MODE OF LINE.
Press 6 = pulse/tone dialingQ-.Press 7 = ton8 only dialing7. ABANDONED HOLD RECALLTIME. Press8=5Omsec. Press 
6Y3C0 msec.
8.SELECT NEXT LINE FOR PROGRAMMING.
Press Bl-B8 (model 0616X).
Press ByB6 (model 0616X)
9. END LINE g PROGRAMMING
. Press S MONITORNOTE: 
If a timeout occurs during the ptvgrammlng seqoence, perform base level entry again and proceed at any
progmm step.
RECORD
(Shading Denotes System Default Values)I
NOlECheck each line number block for rhe fine featwu that is sdIWrfte in the calling number and locaffon status.
NON-PRIVATE NON-PRIVATE
DISABLED 1/
RESTRICTION RESTRICTION
CALLING NO. CALLING NO.
Change page 
41913-65 
						

							IMI 66-031System Programming
Table 3-3. Statlon COS Programming Reference
(Copy 
this sheet as required)
PROCEDURE
Circle or enter the record v&es st right before
RECORD
Enter lnfotmstion or circle desin?d veh8 below before
2. 
DlALTWO-DIGITPORT NUMBER
. Press RECALLINTERCOM NUMBER
4. CONFIGUF& PA PORT (opti
[(06,6X)!, 12 (3 14 15 16 I~~M~ji&j$jj~. . . . _ ..:..:c...: ::. . . . . . . . . . . . .
ressBl-B6(model D616X). Press4
(0816X) 
11 /2 13 (4 15 16 17 1. Press6
.
Press Bl-B6 (model D616X).
Press By-& (model 0816X) 
						

							IMI 66-031System Programming
Table 3-3, STATION COS PROGRAMMING REP ERENCE (Continued)
(Copy this sheet as required)
PROCEDURE
circle or enter therecordvalues at right
14. ALL 
CALLAND ZONE PAGING
.Press # lTCM to clear allcall..
Press keys: Bl-B4 = receive A. B, C, and all-call.
Press keys: BS-B8 = originate A. B. C and allcall
0 Dial l-6 (0616X)
. Dial 
147&16X)
usedkeyand light. Press*
17. PROGRAM NEXT 
STATlON.Repeat procedure from step 218. END 
P&&AMMING.Press MONITOR
NO7E If a timeout occurs during the progmmmfngsequence, perform base level entry again and
proceed at any progmm step.
3-17