Comdial Executech Lcd Speakerphone Instructions Manual

							Executech LCD 
Speakerphone 
This user guide is applicable for the following system 
models: 
l 14328 Rev F and later 
l K2232C Rev C and later 
l K2264 Rev C and later 
l K2296 Rev C and later 
User’s Guide ; 
GCA 70-135.02 
2190  
						

							Table Of Contents  
						

							4  
						

							Introduction 
This Executech LCD Speakerphone provides the 
user with a Liquid Crystal Display (LCD) in addition 
to the many standard available features. In the 
idle state, this l&digit LCD provides a desk clock 
and calendar combination, When a call is in 
progress, an elapsed time display provides a con- 
stant reminder of call duration. Other call handling 
and information displays make telephone use 
easier and more efficient. 
All display functions occur automatically as call 
processing and handling proceeds, One manual 
operation (Call Messaging Display) is available for 
use where needed. 
5  
						

							The Basics 
Placing A Call 
0 Press line key to select line. 
Or 
0 If line groups are provided, press ITCM then dial access 
code for desired group. 
NOTE Selecting a line is not necessary if a line has 
been assigned to you or if your telephone automatical- 
ly picks an idle line for use when the handset is lifted. 
A system selected idle line that is normally not assigned 
to your telephone may appear on a line key reserved 
for that purpose during the time that the line is in use (if 
this feature is programmed). 
LI Listen for dial tone. 
RESULTS: Display will show line selected for use. 
., 
~ .‘:.:.“‘.:‘::.:.:::‘:..:::~,~~~~~~~~,~,~,~~; 
..:.:.:.:.:.:.:.:.:.:.:.:.:.?: . . . . . . . . . . . . . . . . . . 
0 .Dial number. 
RESULTS: Display will show dialed number. 
1. Typical host system extension. $$..T ::....... :.: . . . . . . . . . . . ...’ ii.... .:.:...:.:.:.:.:.:.:.:.:.:.:.:.:.:.. 
f 
. . . . . . . . . . . . . . . . .A.. 
2. Typical trunk number. 
3. Typical access code preceding typical trunk 
number. 
6  
						

							When party answers, 
a Speak toward telephone or lift handset for private con- 
versation 
To return to speakerphone from handset, 
0 Press MNTR key. R Hang up handset. 
To end call, 
0 Press MNTR key or hang up handset if engaged in 
private conversation. 
Call Timer 
RESULTS: Approximatetly twenty seconds after dialing is 
complete Call Timer shows elapsed time of call. 
RESULTS: Elapsed time will show for ten seconds after call 
is completed. 
To recall elapsed time any time after display has dropped and 
before another call is made, 
Q Press HOLD. 
RESULTS: Elapsed time will appear in display and remain 
for fifteen seconds. 
Answering A Call 
0 Press line key of ringing line (line key with flashing light). 
0 Speak toward telephone. 
If your assigned line is ringing or if your telephone is programmed 
to answer any ringing line, 
Q Lift handset then switch to speakerphone (if desired) by 
pressing MNTR and hanging up handset. 
NOTE: If your telephone can answer any ringing line, 
one that is normally not assigned to it may appear on a 
7 
(continued on next page)  
						

							,continued from previous page) 
line key reserved for that purpose when it is answered. 
(if this feature is programmed). 
RESULTS: Display will show answered line, 
Placing A Call On Hold 
Marauca~ hold (Any telephone with line appearance can retrieve 
held call.) 
0 Press HOLD. 
To return to call on hold, 
0 Press line key with flashing light. 
Exclusive 
hold (Only your telephone can retrieve held call.) 
0 Press HOLD twice. 
Hold recall feature 
After a preprogrammed length of time, a call 
placed on hold will automatically ring back to the 
telephone which placed it on hold. If the call is on 
exclusive hold, it will revert to manual hold after the 
hold recall time period and can be retrieved by 
anyone with that line appearance. 
RESULTS: Display will show line and telephone station 
number each time that the timed hold recall 
occurs. 
Placing Intercom Calls 
Intercom calls may be manually dialed as described below or 
automatically dialed as described in the paragraph provided 
later titled Direct Station Selection/Busy Lamp Field.  
						

							Voice Calling 
0 Lift handset. 0 Press ITCM. 0 Dial extension number. 
(To call system operator, dial 0.) 
RESULTS: Display will show dialed extension. 
~ 
.,. . . . . . . . . . . . . . . . ,...,................... 
0 Speak to called party. 
Tone Calling 
0 Press ITCM. 0 Dial extension number, 
RESULTS: Display will show dialed extension. 
~ 
.,.,.,........ 
B Press ITCM again. 
RESULTS: Called telephone will ring. 
When called telephone answers, 
0 Speak toward telephone or lift handset for private con- 
versation 
NOTE Some systems may be programmed to tone sig- 
nal as the first option. In that case, press /XX4 key 
again to voice call the party instead of making the 
called telephone ring. 
Answering Intercom Calls 
RESULTS: Display will show extension number of calling 
telephone. ~ 
. . . . . . . . . . . . 
-:.:-:.:.:.: :,... :.>::..:...:...:::..:.: . . . . . . . :...: . . . . . ):.:.5:.:.:.:.: . . . . . . . .,.,.,. .,.,.,_,.,_,.,.,. 
To answer a voice call, 
0 Speak toward the telephone. 0 Lift handset if privacy 
is desired. 
(continued on next page) 
9  
						

							(continued from previous page) 
NOTE: Voice calling can be blocked. See the discus- 
sion titled, Voice Signal Blocking for details. 
To answer a tone call, 
0 Lift handset to 
talk or press ITCM and speak toward 
telephone. 
Direct Station Selection/Busy Lamp Field - DSS/BLF 
(One key intercom calling with visual indication of telephone 
status) 
To program, 
0 Press ITCM. Listen for tone. Cl Dial 85. Tone will stop. 
0 Press memory key. Cl Dial extension number. 0 
Repeat last two steps for all desired telephones. 0 
Press MONITOR. 
NOTE: An autodial number can also be programmed as 
a secondary function at every DSS/BLF memory loca- 
tion. See Automatic Dialing Insffucfions for details. 
To voice call a number, 
m Lift handset. Q Press memory key. 0 Voice an- 
nounce. 
NOTE: If you are transferring a call, the outside line is 
automatically placed on hold when a DSS key is 
pressed. 
To tone call a number, 
0 Lift handset. 0 Press memory key. 0 Press ITCM. 
When telephone answers, two-way conversation can 
take place. 
NOTE: The lights (LEDs) adjacent to memory keys indi- 
cate status of DSS telephones: dark indicates idle 
telephone, steady-on indicates telephone in use, and 
flutter indicates telephone call back request. 
10