Comdial Executech 2232 HYBRID/KEY SYSTEM Instructions Manual

~
IiMONTH/DAY/YEAR
CALL DURATION TIME-MINUTES. TENTHS
(NO ANSWER, PRINTS “NOANS”)
40 COLUMN
PRINTOUT
LINES
(SEE YoTE *)
2ANSWER TIME-MINUTES. TENTHS
CALLS 
ONLY-THAN 9.9, PRINTS ‘I???“)(CARRIAGE RETURN 1
[LlNEl1 CARRIAGE 
RETURN)[FEED)I
Y2
1.
2.
3.
-DIALED DIGITS-UP TO MAXIMUM OF 32
(ACCOUNT CODES ARE ISOLATED BY * OR # SYMBOLS
NOTES
CARRIAGE RETURN AND LINE FEED IMMEDIATELY
FOLLOWm LAST PRINTED CHARACTER ON EACH
LINE. ALSO SEE NOTE 2.
ILLUSTRATED PRINTOUT IS40 COLUMN, TWO-LINE
FORMAT. FOR 80 COLUMN...

IMI 66-047
CASSETTE TAPE RECORD OF COS VALUESProgramming 
l Connect audio cassette tape recorder to music interface on side of
KSU.
l DO not perform other programming action while tape system is active.
l Program baud rate of tape data to be 100 or SO baud as desired. (See
System COS programming discussion for details.)
0 If the system includes a data printer,appropriate response messages
will be printed during the recording and loading of COS data.
RECORDIXG COS DATA TO TAPE----- -----
To record...

r ’ IMI 66-047Programming
VERIFING TAPE DATA (Requires Data Printer)
To verify previously recorded cassette tape,
0 Rewind pre-recorded cassette tape, and prepare recorder
for play-back.
0 PressITCM * 7 4 6 * ITCM
l Start tape playback
0 Press program key C39
0 Printer will print status as follows:
VERIFY COS DATA TAPE
VERIFY TAPE 
DirTA COMPLETE
VERIFY TAPE DATA ERROR
LOADING COS DATA FROM TAPE--- 
- ---
To load previously recorded COS program values into system to replace
current program values,...

IMI 66-047Programming 
SYSTEM CLOCK INFORMATION
All clock setting and adjustment 
must be performed from station port
10 or 11.SETTING THE CLOCK
1.PressITCM, then dial*#
2.
Dial the clock date with the key pad keys
YEARMONTH
DAYHOURMINUTE
NOTE
Values less than 10 must be dialed as OX.
Hours must be expressed in the 24-hour format.
3.If the SMDR printer is installed and operating, the clock date
will be printed as follows.
** 
01/08/86 16:OO(Example)
4.Reset the minutes setting, if necessary, as follows:...

s ’* IMI 66-047
SYSTEM SPEED DIAL PROGRAMMINGProgrammingFifty (SO) system speed dial numbers can be stored from station port
10 or 11 for use at all stations in the system.
System speed dial
numbers will not 
be toll restricted unless specified by station COS
programming.
0 PressITCM *
0 PressSAVE
0 Dial storage location (10 - 59)
0 ChOOSe line or group preselection(multifunction (hybrid) system only)
0 Dial 1 -4 for group
-or-@ Press a line key for line
Note:Key-to-line assignment per programming...

IMI 66-047
.
ProgrammingTOLL TABLES
rSYSTEM COS
III
II
@EXECCONSOLEw/o CALLANNOUNCE@:EXEC
EE”” ,#’PNNOUNCE@g :LcD@):SINGLELlNElHOTELl@:3&a LINE@222 LINE
@SINGLE
LINEIAGMINJ000
FOR EXT. NO.
ilOO-/  I BAUD RATE
TOLLTABLESc
SPEClFY CONSOLE TYPE FOR EACH CONSOLE PORT
SPECIFY CONSOLE PORT
SPECIFY CONSOLE TYPE
Figure 3-3a.Programming Reference Chart
3-26 

n I
IL11 66-047Programming
7 PROGRAM ENTRY
LINE COS
GROUP:@‘NONE@)-GPI@:GPZ@:GP3Q:GP4klODE:@I: PULSEQ:TONEPRI VACY RLS:@,:OlSABEO@= ENABLED
TOLL TABLES:
Q:ERASE
ABAND HOLD
RLS:STATION COSPRINTOUT
@ PA PORT0 VOICE BLOCKa EXECUTIVE OVERRI OEc@ SYSTEM SPEED DIAL@AUTO HOLDTOLL RESTRICT@t&G. WAIT ORIG.
Q,@,@m=RING TONE 122 LINE KEYSET ONLY1
SELECT PRIME LINE: CHART KEY):LINE:ORfi& OR @,@,@@,@:TRUNK GROUPS I  -4
@FOR RINGING LINE PREF.
C~RINGING -@DELAYED RINGING -@NIGHT TRANSFER -
1
:;k;CT FEATURE
@AUTO...

STATION 10 - PROGRAMMING OVERLAY
l Cut out along border.
l Cut out shaded openings.
l Fit over station faceplate.
Al Al
A2 A2
A3 A3
A4 A4
A5 A5
A6
, A7
IA6
A7
EXECUTECHA8
PROGRAMMINGA9
OVERLAY703804 -274A10
All
Al2
Al3
Al4
84 B5B687 &?
Bl8283 

‘STATION 10 
- PROGRAMMING OVERLAY
l Cut out along border.
l Cut out shaded openings.
l Fit over station faceplate.
Al
A2
A3
A4
A5
A6
A7
07
B5
83
I31703500-566
PROGRAMMINGA8
A9
OVERLAYAI0All
Al2
Al3
Al4
88B6
84
82 

CONSOLE - PROGRAMMING OVERLAYl Cut out along border.
l Cut out shaded openings.
l Fit over console faceplate.
703500-567
PROGRAMMING OVERLAY
C70 C7l C72 c73 C74 C75 C76 C77 C78 c79
C60 C6l C62 C63 C64 C65 C66 C67 C68 c69
C50 C5l C52 C53 C54 C55 C56 C57 C58 c59
C40 C4l C42 C43 C44 C45 C46 C47 C48 c‘+g
c30 c31C32 c33 C34 C35 C36 C37 C38 c39
c20 C2lC22 C23 C24 C25 C26 C27 C28 (29
Cl0CIICl2Cl3 cl4 Cl5 Cl6
cl7 Cl8 Cl9