Comdial Executech 2232 HYBRID/KEY SYSTEM Instructions Manual

							~
IiMONTH/DAY/YEAR
CALL DURATION TIME-MINUTES. TENTHS
(NO ANSWER, PRINTS “NOANS”)
40 COLUMN
PRINTOUT
LINES
(SEE YoTE *)
2ANSWER TIME-MINUTES. TENTHS
CALLS 
ONLY-THAN 9.9, PRINTS ‘I???“)(CARRIAGE RETURN 1
[LlNEl1 CARRIAGE 
RETURN)[FEED)I
Y2
1.
2.
3.
-DIALED DIGITS-UP TO MAXIMUM OF 32
(ACCOUNT CODES ARE ISOLATED BY * OR # SYMBOLS
NOTES
CARRIAGE RETURN AND LINE FEED IMMEDIATELY
FOLLOWm LAST PRINTED CHARACTER ON EACH
LINE. ALSO SEE NOTE 2.
ILLUSTRATED PRINTOUT IS40 COLUMN, TWO-LINE
FORMAT. FOR 80 COLUMN ONE-LINE PRINTOUT
FORMAT, CARRIAGE RETURN AND LINE FEED
CHARACTERS AT END OF LINE 1 ARE REPLACED BY
TWO SPACES FOLLOWED BY ENTIRE CONTENTS
OF LINE 2.
OUTGOING CALL MUST BE OFF HOOK FOR 20
SECONDS MINIMUM OR NO RECORDING OCCURS.PRINTOUT EXAMPLES
1UNANSWERED INCOMING CALL
112/05/861651NOANS 0.6
ANSWERED INCOMING CALL
16112/05/8616:521.6 0.2
ANSWERED INCOMING CALL
24112/05/8616:531.2 0.2
(WITH CALLER ID ADDED BY“1234
STATION DURING CALL)
OUTGOING CALL (LOCAL)
16212/05/8616:58
2.0I1 9782200IIOUTGOING CALL24 2 12/05/86 17:Ol.5(WITH ACCOUNT CODES)11233456789’0#*7412580#9631*#AC POWER FAILURE AND
-RE$TORATIOtiOFFTIME l *l2/05/86 17:03**12/05/86 17108
Figure 3-2.SMDK Printout Details 
						

							IMI 66-047
CASSETTE TAPE RECORD OF COS VALUESProgramming 
l Connect audio cassette tape recorder to music interface on side of
KSU.
l DO not perform other programming action while tape system is active.
l Program baud rate of tape data to be 100 or SO baud as desired. (See
System COS programming discussion for details.)
0 If the system includes a data printer,appropriate response messages
will be printed during the recording and loading of COS data.
RECORDIXG COS DATA TO TAPE----- -----
To record currently stored COS program values on cassette tape for
later use,proceed as follows:
1.Install blank cassette tape,and prepare recorder for recording.
2.Cause recorder to-begin recording blank cassette tape from
beginning.
3.PressITCM * 7 4 6 * ITCM
4.Press appropriate program key to start recording process.
l c37= COS FEATURES
l c34= ALL SPEED DIALS
l c35 =AUTODIALS (STA 010 - 025)
l C36 =AUTODIALS (STA 026 - 041)
5.To abort procedure (if required),
l Press ITCM * 7 4 6 * ITCM
l Press program key C41.
COS recording requires approximately 12 minutes.Station port 10 or
11 will ring when recording is complete.
COMPARING RECORDED DATA (Requires Data Printer)
.To compare recorded values with system values,
l Rewind cassette tape,
l Press ITCM
and prepare recorder for playback.* 7 4 6 
* ITCM
l Press program key C38
l Start tape playback
l Printer will print status as follows:
COMPARE TAPE TO COS DATA
COMPARE TAPE COMPLETE
COMPARE TAPE DATA ERROR
3-22 
						

							r ’ IMI 66-047Programming
VERIFING TAPE DATA (Requires Data Printer)
To verify previously recorded cassette tape,
0 Rewind pre-recorded cassette tape, and prepare recorder
for play-back.
0 PressITCM * 7 4 6 * ITCM
l Start tape playback
0 Press program key C39
0 Printer will print status as follows:
VERIFY COS DATA TAPE
VERIFY TAPE 
DirTA COMPLETE
VERIFY TAPE DATA ERROR
LOADING COS DATA FROM TAPE--- 
- ---
To load previously recorded COS program values into system to replace
current program values, proceed as follows:
1.
2.
3.
4.
5.
Install pre-recorded cassette tape,and prepare recorder for
playback
Press ITCM * 7 4 6 * ITCM
To load COS features,l Press HOLD
-or-
To load memory dialing numbers,
0 Press RECALL
Start tape playback.
To abort the procedure (if required),
l Press ITCM * 7 4 6 * ITCM
0 Press program key C41.
CGS loading requires approximately 10 minutes.Station port 10 or 11
will ring when loading is complete.
3-23 
						

							IMI 66-047Programming 
SYSTEM CLOCK INFORMATION
All clock setting and adjustment 
must be performed from station port
10 or 11.SETTING THE CLOCK
1.PressITCM, then dial*#
2.
Dial the clock date with the key pad keys
YEARMONTH
DAYHOURMINUTE
NOTE
Values less than 10 must be dialed as OX.
Hours must be expressed in the 24-hour format.
3.If the SMDR printer is installed and operating, the clock date
will be printed as follows.
** 
01/08/86 16:OO(Example)
4.Reset the minutes setting, if necessary, as follows:
a.Repeat step 1.
b.Dial the new minutes digits, and press the# key.
C.
A new clock date printing will occur.
5.To obtain a printing of the current clock date,
pressITCM * # #
Printing will occur automatically once each 24-hour period.
** 
MO/DY/YR 0O:OO(current date and 0O:OO hours)
POWER INTERRUPTION
The system clock will continue to run for at least 30 minutes after AC
power has been removed from the system.If power is restored within
the 30-minute backup period,the following printing sequence will
occur:
LAST VALID CLOCK =MO/DY/YRHR:MN(time of power outage)
MO/DY/YRHR:MN(time of power return)
If power is not restored within the backup period, the following
printing sequence will occur when the power is restored.
CLOCK NOT VALID
12/01/86 0O:OO(default clock date)
The clock will begin running from the default date.It must be reset
to the current date per the instructions above.
3-24 
						

							s ’* IMI 66-047
SYSTEM SPEED DIAL PROGRAMMINGProgrammingFifty (SO) system speed dial numbers can be stored from station port
10 or 11 for use at all stations in the system.
System speed dial
numbers will not 
be toll restricted unless specified by station COS
programming.
0 PressITCM *
0 PressSAVE
0 Dial storage location (10 - 59)
0 ChOOSe line or group preselection(multifunction (hybrid) system only)
0 Dial 1 -4 for group
-or-@ Press a line key for line
Note:Key-to-line assignment per programming arrangement.
Refer to station COS programming reference chart
for station port 10 key-to-line assignments.
-or-
l Dial 0 for no group or line preselection
0 Dial speed dial number (up to 32 digits)
eDia1 l-0,#,and *
l PressHOLDto store pause if required
l PressRECALLto store flash if required
@ PressSAVE and repeat procedure for each number.
0 PressMONIT3Rto end procedure
SYSTEM SPEED DIAL INDEX
*lo*27I *45 I
*11 II *38I*46
*47, 
t30f48
“14*31*49*-lr; II *77*50
--.I.” ,*51*17 II *l/lI“52
*53*c A
“55 1
3-25 
						

							IMI 66-047
.
ProgrammingTOLL TABLES
rSYSTEM COS
III
II
@EXECCONSOLEw/o CALLANNOUNCE@:EXEC
EE”” ,#’PNNOUNCE@g :LcD@):SINGLELlNElHOTELl@:3&a LINE@222 LINE
@SINGLE
LINEIAGMINJ000
FOR EXT. NO.
ilOO-/  I BAUD RATE
TOLLTABLESc
SPEClFY CONSOLE TYPE FOR EACH CONSOLE PORT
SPECIFY CONSOLE PORT
SPECIFY CONSOLE TYPE
Figure 3-3a.Programming Reference Chart
3-26 
						

							n I
IL11 66-047Programming
7 PROGRAM ENTRY
LINE COS
GROUP:@‘NONE@)-GPI@:GPZ@:GP3Q:GP4klODE:@I: PULSEQ:TONEPRI VACY RLS:@,:OlSABEO@= ENABLED
TOLL TABLES:
Q:ERASE
ABAND HOLD
RLS:STATION COSPRINTOUT
@ PA PORT0 VOICE BLOCKa EXECUTIVE OVERRI OEc@ SYSTEM SPEED DIAL@AUTO HOLDTOLL RESTRICT@t&G. WAIT ORIG.
Q,@,@m=RING TONE 122 LINE KEYSET ONLY1
SELECT PRIME LINE: CHART KEY):LINE:ORfi& OR @,@,@@,@:TRUNK GROUPS I  -4
@FOR RINGING LINE PREF.
C~RINGING -@DELAYED RINGING -@NIGHT TRANSFER -
1
:;k;CT FEATURE
@AUTO pRiv.RLs -SELECT LINES WITH
@ACCESS DENIED -@ELECTI 0~ CHART KEYS
QORIG. DENIED -@IDLE LINE PREF. -0 ASS I GN TOLL TABLES :@ -@I:TABLES l-16ORESERVE ITCM LINK:Q--Q:SELECT LINKS I -7
-or-
@Jf)-NO RESERVED LINK@I TO CONTINUE
0 ALL-CALL/ZONE PAGING: (E~~P:CLEARS ALLa:ALL CALL ORIG.@Q=ALL CALL REC.a-a:ZONES I-3 ORIG.a-a:ZONES I-3 REC.@ KEY MAPPING MODE: 1DEPENOENT UPON PHONE TYPEIPRESS KEY TO BE DEFINED THEN PRESS FUNCTION.
~~~ :LINES I-22
0 0 OPORT 
ID’:DSS&LF
B :BLANK/AuT~~~AL/~YNAMIc loop KEYIBI w.831I
*PORT I D:0010 TO 041 FOR.OlO TO 073 FOR0010 TO 105 FOR
MODEL
MODEL
LlODEL2232KSU
2264KSU
2296KSUDEFAULTTAPE
SYSTEM
DEFAULT
ENTRY
SPECIFY:
a:SYSTEMQZLINEQ:STATIONa-PULSEQ:TONEa:KEY MMm:TAPE !&MDRATE OF I O(?i% -TAPE BAUDRATE OF 50
I@ :RECORD ALL
LPRINTOUT
ONE 
STATI ON
Figure 3-3b.Programming Reference Chart3-27 
						

							STATION 10 - PROGRAMMING OVERLAY
l Cut out along border.
l Cut out shaded openings.
l Fit over station faceplate.
Al Al
A2 A2
A3 A3
A4 A4
A5 A5
A6
, A7
IA6
A7
EXECUTECHA8
PROGRAMMINGA9
OVERLAY703804 -274A10
All
Al2
Al3
Al4
84 B5B687 &?
Bl8283 
						

							‘STATION 10 
- PROGRAMMING OVERLAY
l Cut out along border.
l Cut out shaded openings.
l Fit over station faceplate.
Al
A2
A3
A4
A5
A6
A7
07
B5
83
I31703500-566
PROGRAMMINGA8
A9
OVERLAYAI0All
Al2
Al3
Al4
88B6
84
82 
						

							CONSOLE - PROGRAMMING OVERLAYl Cut out along border.
l Cut out shaded openings.
l Fit over console faceplate.
703500-567
PROGRAMMING OVERLAY
C70 C7l C72 c73 C74 C75 C76 C77 C78 c79
C60 C6l C62 C63 C64 C65 C66 C67 C68 c69
C50 C5l C52 C53 C54 C55 C56 C57 C58 c59
C40 C4l C42 C43 C44 C45 C46 C47 C48 c‘+g
c30 c31C32 c33 C34 C35 C36 C37 C38 c39
c20 C2lC22 C23 C24 C25 C26 C27 C28 (29
Cl0CIICl2Cl3 cl4 Cl5 Cl6
cl7 Cl8 Cl9