Comdial Executech 2232 HYBRID/KEY SYSTEM Instructions Manual

0IMI 66-047Installation
Table 2-3.Wiring For Station Connector Block J-3SYSTEM INTERCONNECTION FOR KSU 
53KSU IN
CONNECl
25PAI3LE
CONNI,Lu s ANSI -IInWIRE COLORPAIR, I”“. ,I, -, . . . . .WHITE-BLUE1 26 1 STATION 
AVOICEGREEN 1  1 TERFACE
TOR WIRINGCONNECTION BLOCK WIRINGIR CABLE
ECTIONSASSIGNMENT4-WIRE CAECON~lCPT’f
PIN(DEFAULT EXTENSIONLB,-,SHOWN)COLOR 1 bL’rTFRhABLUE-WHITE
I’I1PORTPAIR1RED12WHITE-ORANGE11
2730 /I EXT.DATA1YELLOW13_ORANGE-WHITE22v130(PAIR1BLACK4WHITE-GREEN
2!~(STATION /I VOICE I...

.
Installation
IMI 66-047
Table 2-4.Wiring For Auxiliary Connector Block J-4SYSTEM INTERCONNECTION FOR KSU 
54KSU 
IICONNEC
25-P/^A. . .NTERFACE
:TOR WIRINGCONNECTION BLOCK WIRINGI
iIR CABLE4-WIRELUNNECTIONSASSIGNMENTCONNEL . ..,I _.I(DEFAULT EXTENSIONCLI.
PAIRPIN
NO.SHOWN)COLORTERM.IWIRE COLOR 1
rm WHITE-BLUE 126POWER FAILTIP1
1
1
STA. 1RINGvc-““rll I I:2
vvn,TE-ORANGE27POWER FAILRING13ORANGE-WHITE
22STA. 2TIP4WHITE-GREEN1 28 1 POWER FAIL 
)TIP1r,RFFN-WHITF3131STA.31RING116II7_..__. _ . ....

IMI 66-047Installation
Table 2-5.Wiring For 
CO/PSX Connector Block J-5ORP 
.--RED-GREEN
tBLACK-SLATE
ORANGE-YELLOWCLIP
TERM.ICONNECTION BLOCK WIRING
2-13 

IMI 66-047Installation
r--CONNECT TO CLIP TERMINALS ON- 1 CONNECTOR BLOCK PER CHART+
I\ (18-B- 24V @e MAXOUTPUT ASLOW
AKSU1 INTERNAL ‘,1REQUIRED BYVOLTAGE(IA!a\,Gl CA LA&Ynr, A” et?,,POWER1 SWITCHING ,‘-,- _nCLnr U”ILI
-----
P-tVOLTAGE CLAMPING DIODE
RECOMMENDED
at*.r-,  bSLAVE 
’RELAY ’b
!-S.I--SIGNALLING 9DEVICE
I
Ic
‘OWER;OURCEI-FUNCTIONCONNECTIONS
COMMON AUDIBLEJ-l CLIPS 
49,50STATION 17 RINGINGJ-2 CLIPS 
49,50
Figure 2-2.Common Audible/Auxiliary Station Interface Wir
(Typical Connection)600 
A TO...

: IMI 66-047Installation
L
Figure 2-4a.System Interconnection - Typical Connections
2-15a 

IN1 66-047Installation -
,--,--2--,--. --/--
Figure 2-4b.System Interconnection - Typical Connections
2-15b 

IMI 66-047Installation
2-16 

IMI 66-047Installation
SYSTEM CHECKOUT
Initial Condition_-
The system operating features are set to a set of default conditions
at initial power up.These conditions provide a basic operating
system with a known set of parameters,
and the system should be
initially checked out with the default conditions in place. At
anytime while the system is operating,
default conditions can be reset
from station port 10 or 11 per the instructions provided in Chapter 3.
Check Out
--.-
Check the KSU and telephone...

IMI 66-047Installation
Voltage Check
LYake the following voltage measurements at the station connector
blocks under the following conditions
l Bridging clips installed
@AC power connected to the KSU
UNIT UNDER
I
66M-XX BLOCK METER LEAD
II
MEASURED
TESTCONNECTIONPOLARITY
VOLTAGE
I
TYPICAL EVEN
STATION
Repeat for
each even sta.
TYPICAL ODD
STATION
Repeat for
each odd sta. Measure the voltage across one voice line and one data line and then
across the other voice line and the other data line for each even...