Comdial Executech 2232 HYBRID/KEY SYSTEM Instructions Manual

IIMI 66-U47CHAPTER 3
SYSTEM PROGRAMMING
GENERAL INFORMATIONProgramming
0 Class Of Service (COS) programming consists of the following major
categories:General System COS, Toll Table Entry, Line COS, and
Station COS.
l All COS programming commands must originate at a 22 Line/Feature
Keyset installed at station port 10 or 11 and a companion DSS/BLF
Console installed at console port 
1Cla or lla respectively.No COS
programming commands -will be accepted from any other stations
connected to the system.
l...

IN1 66-047.
Programmi.1g
SPECIAL PROGRAMMING REaUIREfqENTS
FOR SINGLE-LINE KEYSETS
Several programming steps under COS programming must be observed 
for
proper operation of a Single-Line Keyset.
@When the system is strapped for key system configuration, the
Single-Line 
Keyset is an intercom only station.It can be
configured for private line only by programming the applicable
station port for the prime line automatic feature.When the port is
programmed with the prime line automatic feature, the...

I ’IMI 66-047Programming
CLASS OF SERVICE DEFAULT
The system can be defaulted to a standard class of service per the
following procedure.The default conditions are listed at the
beginning of each COS programming procedure and shaded on the
programming reference charts.
1PressITCM * 74 6 *
2 Press program key C38
3Press keypad key(s) to choose default settings
1= system COS default4= pulse dialing - all lines
2 
= line COS default
5 = tone dialing - all lines
3 =station COS default6= flexible key/function...

OVERLAY: 703804-274OVERLAY: 703804-275OVERLAY: 703500566OVERLAV: 703500467
0b
00..OO0000.OO0000
El3
00
000000..OO00,*00
0000000000
0000000000
0000000000
0000000000. . .
t6.300~0000000000
JFigure 3-l.Programming Overlay Identification 

Programming
SYSTEM COS PROGRAMMING PROCEDURE
------------------------
--------_-------____---------------------
SYSTEM DEFAULTS
0 Recall/flash time = 2 seconds 0 Intercom signalling = voice first
0 Pause time = 1 second0 Central message Desk = not assigned
0 Timed Hold recall timel Unanswered call transfer
= 60 seconds= 20 seconds
0 Printer baud rate = 1200 baud, 7-bit data 0 Print length = 40 Col.
0 Port Assignments: All station ports= 22 Line/Feature Keyset
All console ports= 40-Key DSS/BLF Consoles
l...

IMI 66-047Programming *
System COS programming procedure-continued
10Specify console type for each console port
l Press console program key Cl0 to enable port selection
l Pressconsole program key to specify console port
Clil= console port 10a
Cl1 = console port lla
0 Press
console program key to specify console type
Cl0 =70-Key console
Cl4 =40-Key console
Cl5 =32-Key console
l Repeat port and console selection steps for all required ports
11Select baud rate of tape data12 Press *
0 Press program key C38...

* IMI 66-047Programming
SYSTEM 
COS PROGRAMMING REFERENCE TABLE
@Shading denotes system default conditions
@Check off values chosen for system being programmed
21 (c34)RECALL/FLASH TIME5A
4r--I
:. :...
@ HOLD RECALL TIME
KEY 1 TIME 1  ENTRY
Note: 0 program selection (disa-
bled) enables exclusive hold condi-
tion (when set at station) to place
line on hold that cannot be releasedat any other station.
6’INTERCOM FIRST CHOICE SIGNALLING
wCENTRAL MESSAGE DESK
STATION PORT ASSIGNED
8
3-7 

1141 65-047
.
Programming
DIALING.. .EXTENSION ,,“,..I
v1cf%?1013rt31014vi41015f15016, 718,0171 1w016E Its.
019llas120
l-E-+---
10 @i9SPECIFY CONSOLE TYPE FOR EACH CONSOLE PORT
CHOOSE PORT
!CHOOSE CONSOLE TYPE
@gPORT 10a@70-KEY CONSOLE8
@PORT lla@40-KEY CONSOLE
@g32-KEY CONSOLE
11 
G3BAUD RATE OF TAPE DATA
KEY1 BAUDRATEENTRY
Change page 31883-8 

TOLL KESIRICl_CON PROGKAPlMIbJ~Programming
In order for toll restriction to take effect, the following three-fold process must occur.
*One or more toll tables must be entered.
lToll tables must be assigned to all appropriate lines.
lToll tables must be assigned to all appropriate stations.
Only the toll table(s) which are entered and assigned to both a line and a station using that line
will invoke any toll restriction.
TABLE ENTRY PROCEDURE
1.Determine the types of dialing restrictions which must be...

IivlI 66-047
1
2
3
4
6
6
Programming
T3LL KES’IKIC’I’ION PROGRAMMING PROCEDURE
PressITCM * 7 4 6 *(base level entry if not active)
Press program 
key C37 (enter toll program mode)Press console key 
Cl0- C25 to select table number (1 - 16)
KEY Cl0 Cl1 Ci2 Cl3 Cl4 Cl5 cl6 Ci7
jlAi3LE12345b7i3
AEYCl8 Cl3 C2O C21 C22 C23 C24 C25
TABLE9101112131415Iti
Select table type
0 deny -
l AllON -press program key 
C33press program key 
C39
Dial number (16 digits max.)
(Press 
k formatch anything
digit)
Repeat steps 3...