Comdial Executech 2232 HYBRID/KEY SYSTEM Instructions Manual

Ib:I 66-047
Programming
IRESTRICTION TABLE 61RESTRICTION TP
i TYPE: ALLOWDENYITYPE: ALLOWDENY
ENTRYENTRY NUMBER (16 MAXIMUM)112345671819110Ill1213141516
1ENTRY NUMBER (16 MAXIMUM)
t i
ITABLE ASSIGNMENT: LINES 
-STATIONS
IRESTRICTION TABLE 9IRESTRICTION TABLE 10
TYPE: ALLOWDENY
1 TYPE. ALLOWDENYI
lil2 13 I4 15NTRYENTRY NUMBER (16 MAXIMUM)I(2(415(6(716(10 (11(12(13 (14 (15 116NTRYENTRY NUMBITABLE ASSIGNMENT: LINES 
-STATIONS
RESTRICTION TABLE 11RESTRICTION TABLE 12
DENY
ITYPE: ALLOWDENY1 TYPE: ALLOW
TABLE...

IMI 66-047
.
Programming
LINE COS PROGRAMMING
-----_-___--_---_------------------------------------------------
LINE DEFAULTS
l Line type = TELCO
0 Dial Mode = DTMF
0 Toll Tables = none
assigned
0 Line groups= none assigned
0 Privacy status = private
l Abandoned Hold Timeout = 50 msec.
----------------__-----------------------------------------------
PROCEDURE1 Press
ITCM* 7 4 6 * (base level entry if not now active)
2 Select line to be programmed.
Perform all applicable steps.
0 Press program key per...

’ IMI 66-047Programming
LINE COS PROGRAMMING REFERENCE TABLE
l Shading denotes line default conditions.
. Check off 
or enter the values chosen for the lines being programmed.
-
3
4
5
6
7
EATURE
iELECT
INE
SROUPS
MULTIFUNC
rlON SYS-
:EMS ONLY)
dODE
‘RIVACY
tiODE
rOLL
RESTRICTION
TABLE
ASSIGNMENT
ABANDONED
HOLD TIMEOUT
COlPSX NUMBERS
AND STATION
ASSIGNMENTS
* Power Fail Lines (1, 2. 3, and 4)*+ A-Lead Control Lines (13. 14. 15. and 16)
3-13 

IMI 66-047
.
Programming
STATION COS PROGRAMMING
-___-------------------------------------------------------------
STATION DEFAULTS
l PA port= disabled0 Executive override = disabled
l Ringing line preference0 Prime line/group = none
=disabled0 Single Line Keyset accesses intercom
0 Personal ringing tone= tone 10 Ringing assignment = all lines ring
0 Toll tables = none assignedon stations 10, 17, 39, and 41
0 Line access denied = none0 Origination denied = none
l Idle line preference = nonel Night...

. IMI 66-047Programming
Station COS 
- continued
8 Choose personal ringing tones
9 Set automatic hold
(22 Line/Feature Keysets)0 Press program key C26
0 TONE 1 =
program key Cl4
. TONE 2 =
program key Cl5
11 Select prime line
l TONE 3 =program key Cl6or prime group
. TONE 4 =
program key Cl7
0 Press program key per chart
to select line 1 
- 22
10 Enable message wait originate
0 Press program key C27or press ITCM to select
intercom line
0 Press program key per
to choose prime groupchart
12
Set ring
0...

IMI 66-047.
Programming
Station COS 
- continued
19a Enter toll table assignment mode 19b Specify toll tables
To clear all toll tables assigned0 Press program key ClO-25
0 Press program key C25
20 Reserve intercom link
0 Press #
l Press keypad key l-7
to reserve link l-7
-or-
0 Press 0 key for no reserved link
0 Press console key Cl8 to
continue with next step
21 ~~;~;sal~-call and/or zone paging
l Press RECALL to disable all paging assignments (if desired)
ALL-CALL
0 Press program key A4 to originate
l...

1 IMI 66-047Programming
Station COS
- continued
22 Specify flexible key/function assignment
(non-square configuration), if required.
3 AND 
& LINE KEYSET
l Press program key C39
l Press program key C34 -C41 to choose line keys 1 - 8
- Fast tone bursts will sound
0 Press program key per step 11 chart to assign lines 1 - 22
-or-
* Press RECALL key to disable line appearance
- Tone bursts stop
0 Repeat for each line assigned
22 LINE/FEATURE 
KEYSET
l Press program key C39
Assign Lines To 
Keys
l Press key...

IMI 66-047Programming .
Station COS- continued23 Press *
24a Choose next station port for programming
0 Press program keyc41
0 Press keypad keys 010 - 041
-or-
24bBlock program a group of stations with same COS as previously
programmed station
l Press BOLD
@ Press keypad keys to specify model station
0 Press keypad keys to specify first station in block
l Press keypad keys to specify last station in block.
Note:
Flexible key/function assignments for station port 10 or 11
cannot 
be changed by block...

, IMI 66-047Programming
STATION COS PROGRAMMING REFERENCE TABLE
(Copy This Page To Provide Additional
Referencel 
Shading denoteslinedefaultconditions..Check 
caff or enter the values chosen for
the fines being programmed.
BASELEVEL@~(g@~@STATION PROGRAMMING MODE 
0
Sheets)
15-18 

IMI 66-047
COS AND SMDR PRINTOUTProgramming 

COS PRINTOUT
&hen a data printer is connected to the system, it can be commanded,
from station port 
10 or 11,to print the class of service (COS)
programming configuration.Partial or complete printouts can be
obtained.When the printer is being used to obtain a COS printout,
the Station Message Detail Recording (SMDK) function is temporarily
halteci.SMDR data collection is continued by the system during a COS
printout operation; however,if more than two calls...