Comdial Executech 1432B KSU Instructions Manual

STATION 10 - PROGRAMMING OVERLAY
l Cut out along border.
l Cut out shaded openings.
l Fit over station faceplate.
1(3
BlAl
A2
A3
A4
A5
A6
A7B8
B6
84A0
5x20PROGRAMMING“-’ ‘A9.
OVERLAY
Al0
All
Al2
Al3
Al4
Al5
87B5 

--. --. -.-. .J 1w. w-a.l Cut out shaded openings
l Fit over station faceplate.
PROGRAMMI
INGOVERLAY. 32 BU
703804-456TTON DSSIBLF
$23 C39/I
/ C22 C38 jI
j C23 C39/I/C23 C39/I
j c22 C38 jI; c22 1 C38 ;
.. I -’r
j c21 Ic37/f c21 Ic37;; c21 (c37;II
1I
;C20 C36 iI; C20 1 C36 ;; C20 1 C36 1
f Cl9 c35 III Cl9 c35 III Cl9 c35 III 
Cl8 c34 I
I
+-t-1 Cl7 c33 f
I Cl8 c34 IIf Cl8 C34 1I
/ Cl7 c33 /I
j Cl6 C32 /Ij Cl6’ C32/I
j Cl5 C3l /I1 Cl5 1 C3l 1
j Cl4 Ic30;j Cl4(c30,i
; Cl3 c29 fI;c13 c29;I; Cl3 c29 1
-t-1...

STATION 10 - PROGRAMMING OVERLAY-l Cut out along border.
l Cut out shaded openings.
l Fit over station faceplate.
AlA8
A2
ZXZ-ffiA9OVEMAY
A3A10
A4Al 1
A5Al2
A6Al3
A7
Al4
B7
88B5B6
B3
84
Bl82 

CONSOLE - PROGRAMMlNG OVERLAY
l Cut out along border.
l Cut out shaded openings.
l Fit over console faceplate.
EXECUTECH PROGRAMMING OVERLAY703804 
-276C42 C43 C44 C45C46 C47 C48 C49
c..I(C34 C35 C36 C37C38 C39 
C40 C41 .
C26 C27 C28 C29
C30 C31 C32 C33
Cl8 Cl9 
C20 C21C22 C23 C24 C25Cl4
Cl5Cl6 Cl7 - 

CHAPTER 4
MAINTENANCE
TECHNICAL ASSISTANCE AND REPAIR SERVICE
TECHNICAL ASSISTANCE
Should you experience difficulty with installation,
checkout, or programming, and have made an attempt
to isolate the problem using information provided
herein; or should you encounter problems at a later
date which cannot be resolved by referring to this manual, call the 
Comdlal Technical Service staff.
They can be reached at l-800-368-8224 between the hours of 8:00 AM and 8:00 PM Eastern time, Monday
through Friday....

3.Replace any station that does not pass the self
test.
DSS/BLF CONSOLE SELF TEST
Test the DSS/BLF Console for proper lamp operation
per the following procedure:
1.Disconnect the console line cord p!ug from the line.
2.Press and hold console key Cl0 while
reconnecting the line cord plug to the line.
NOTE: The companion station will b8 disabled during
rh8 rim8 that rh8 COnSOl is being diSCOnn8Cr8d
and reconnected.
3.Release console key ClO, and note that the BLF
indicators will each 
turn on in sequence...

FAILURE
P
ISOLATEFAILED LINE
FROM KSU - DISCONNECTCORRESPONOING TELCOIPBX LINE
INPUT 10 KSUPNOMACSUPPLV
FORlMNUlE-I
CONNECT 
TELCOlPBXINPUT FOR FAILED
LINE TO
UNUSED 
TELCO/PBXLINE PORT ON K$UfR~~sOf31~M
ASSIGNMENT)
1INO
J
Figure 4-l. Failure Analysis Flow Chart 

DESKMlALL REVERSAL
AND WALL MOUNTING
(22Line/Feature Ke
KeyseYset and Single-Line, Only)
CONVERSION
To convert a station from a standard desk model to
one 
which can be hung on the wall, follow the
procedure outlined below.
1.
2.
3.
Remove and discard the pull out directory (22
Line/Feature Keyset, Only)
Remove the lower housing of the station, and
rotate it 180 degrees.
The PWB contains circultty which Is
sensltlve to static electricity discharge. Be
sure that your body and the workplace are
properly...

Wall Plate - Or -  Screws
/:I:Latching Le
ver
Push In 
70 Latch
Pull Out T
0
Housing Screws 
’.. _. -. . .._.(4 Places)
Figure 4-2 Statlon’ Wall Mounting Details
(22 Line/Feature Keyset shown - Slngfe-Line Keyset slmllar)
‘nlatch 

PUBLICATION INDEXAA-Lead Control Device Connections............2-4
....zndone d Hold Timeout Period..............3-Q
AG Power Connection....................2-2
AccessDenied......................3-12AIlCall
 An&Or Zone Paging...............3-l 2AmaPagingInMrface-LinePort.............
.2-SAmaPagingInterface-StationPAPort...........2-5
Auto&l AndDynamic Line Button Assignment......3-13
Automatic Hold......................
3-l 1
Automatic Privacy Release................3-12...