Comdial Executech 1432B KSU Instructions Manual

Voltage CheckGeneral Check
Make the following voltage measurements at the
station connector blocks under the following conditions:
l Bridging clips installed
l AC power connected to the KSU
Measure the voltage across one voice line and one
data line and then across the other voice line and the
other data line for each even and odd station. The
measured voltage must be per the following chart.
Variant readings can indicate a possible wiring,
station, or KSU problem.
1.Check the red light emitting diode...

CHAPTER 3
SYSTEM PROGRAMMINGGENERAL INFORMATION
Class Of Service (COS) programming consists of
the following major categories: General System
COS, Toll Table Entry, Line COS, and Station COS.
Class of service programming can be performed
from 
either station port 10 or station 11. In addition,
a 
32-button DSS/BLF console must be installed in
the adjunct port 10 or 11 respectively.
l When programmlng from station port 10,
employ an LCD Speakerphone and take note of
the following important condition: The...

REUSED 8 LINE BLF KEYSET
Even though an 8 Line BLF Keyset is physically
connected to only one station port, it appears to the
system as two data-paired stations. Special
programming is required to enable proper operation of
a reused 8 Line BLF 
Keyset.
The station port to which it is connected must be
programmed for a 3 and 8 Line 
Keyset.
The paired station port must be programmed for an
8 Line BLF 
Keyset atthough it can not be connected
to any equipment.
When the 8 Line BLF 
Keyset is connected to...

SYSTEM COS PROGRAMMING PROCEDURE
SYSTEM DEFAULTSRecall/Flash Time = 2 Seconds
Intercom Signatling = Voice First
Pause Time = 1 Second
Central Message Desk 
- Not Assigned
Timed Hold Recall Time 
= 60 Seconds
Unanswered Call Transfer 
= 20 Seconds
Printer Baud Rat8 = 1200 baud, 7-bit Data
Print 
Length -40 Column
Port Assignments:
- All Station Ports= 22 Line/Feature Keyset
- All Adjunct Ports = 40.button DSS/BLF Consoles
- Station And Adjunct Ports 10 Atways Defautt
1.
2.
3.Press 
ITCM f 7 4 6 +k (base...

8.Set recall time for unanswered call transfer.
l Press program button 87 (Bl , A7, Bl on LCD
Speakerphone).
l Press keypad buttons for time.
1-10sec.6 =60 sec.
2=20sec.7 -90 sec.
3
=25sec.8=120sec.
4=30sec.9=180 sec.
5=45sec.0 =240 sec.
l Press Yc to return to base level.
9.Specify station type for each adjunct port.
l Press console button to identify adjunct port.
C43 = adjunct port 11C44-adjunct port
 12
C45-adjunctpott 13
l Press console button to specify equipment type.
C46 - 8-Line BLF Keyset
C47 =...

SYSTEM COS PROGRAMMING REFERENCE IABLE
l Shading denotes system default conditions.l
Check off values chosen for system being programmedEASE LEVEL 
@ (Iti> (7 (4 (6 a
3PAUSE TIMEHOLD RECAU. TIMEB3 
ID1 U B1LCDPnOriEi1BAUD 
RlTE FOR COS AND SMOR DATA
86 (BlA6LCDPHONE,
6
RECk,.TIME UNANSWERED CULTFUNSFER
887 (8’A7 81 LCDPHONE,II, -‘YEI E&-n”
9ST*TIONADJUNCT PORTTIPEB LINE SLFKEYSETOS/ELF CONSOLEII
3-5 

TOLL RESTRICTION PROGRAMMINGIn order for toll restriction to take effect, the following
three-fold process must occur:
One or more toll tables must be entered.
Toll tables must be assigned to all appropriate lines.
Toll tables must be assigned to all appropriate stations
Only the toll table(s) which are entered and assigned
to both a line and a station using that line will involk
any toll restriction. Toll tables 1 and 2 have entries
defauted in them and these tables are assigned to all
lines by default....

TOLL RESTRICTION PROGRAMMING REFERENCE TABLES
RESTRICTION TABLE 1
‘PE ALLOW
DENY x
II IIII,, , , ,I I
TABLE ASSIGNMENT LINES u STATIONS
RESTRICTION TABLE 3
TYPE ALLOW
UENY
II IIII II II II
41 I I I I I I I I I ! I 1TABLE ASSIGNMENT LINES -STATIONS
RESTRICTION TABLE 7
TYPE: ALLOW
DENYI
II 1I 1IIIII I I 1I I I 1I II I1 I1 II I II I I
TABLE ASSIGNMENT. LINES -TABLE ASSIGNMENT. LINES -STATIONS STATIONSRESTRICTION
TABLE 2TYPE ALLOW 
xDENY
ENTRYENTRY NUMBER (16 MAXIMUM)
12345 6 7 6g101112
13
1415
16RESTRICTION...

Toll Restriction Tables - continuedRESTRICTION TABLE 9RESTRICTION TABLE 10
TYPE ALLOW
DENYTYPE: ALLOWDENY
NTRY 1ENTRY NUMBER 116 MAXIMLJMII
I1112 13 14tS16 17 1619TABLE ASSIGNMENT. LINES 
-STATIONS
ENTRYENTRY NUMBER (16 MAXIMUM)
12345676810111213141516
1I IIII I III I
IRESTRICTION TABLE 11
I IRESTRICTION TABLE 12
TYPE: ALLOW
DENYTYPE. ALLOW
DENY
NTRY IENTRY NUMBER 116 MAXIMUMII
I~12~13~14/15~16~I
1
2
3
4
I ITABLE ASSIGNMENT. LINES -STATIONS
NTRYENTRY NUMBER (16 MAXIMUM)
112 13...

LINE COS PROGRAMMINGLINE DEFAULTS
Line Type = TELCO
Line Groups 
= None Assigned
Dial Mode 
= DTMF
Privacy Status 
= Private
Toll Tables 
= None Assigned
Abandoned Hold Timeout 
= 50 Msec.
PROCEDURE1. PresslTCM+k7466.
2. Choose line to be programmed.
l Press Al -A14= Line 1 - 14.
l Group 3 = C36
l Group 4 = C37
5. Select dialing mode.
l Pulse/tone = C26
l Tone only = C27
8. Select privacy mode
l Private = C28
l Non-private = C29
3. Select line type.
l Disabled = C46
l Auxiliary = C47. 
COlPBX = C48...