Comdial Executech 1432B KSU Instructions Manual

ProgrammingIMI 66-074LINE COS PROGRAMMING REFERENCE TABLE
l Shading denotes line defauk conditions.l
Check off values chosen for lines being programmedBASE LEVEL 
ammamaLINE PROGRAMMING MODE 
0-a
-
34
5-5
-7
e-PROGRAMMED
LINE NUMBER
FEATURE
1i214i5718It0111112I13I14LINE
GROUPS
-DI,
MODE
PRIVACY
MODE
TOLL
RESTRICTION
rABLE
4SSIGNMENT
14I I I I I I I I I I I I I15,.
ABANDONED C4:! 300MSECI I I I II I II,:43
:OIPBX NUMBERS4ND STATIONASSIGNMENTS’ Power Fail 
Lmer (1. 2. and 3)*’ A-Lea.3 Control Lmer (7 and...

L cg Lb; /h?vvSTATION COS PROGRAMMING
STATION DEFAULTS
PA Port - Disabled
Executive Override 
= Disabled
Ringing Line Preference 
= Disabled
Prfme Line/group = None
Personal Ringing Tone = Tone 1
Single Line 
Keyset Accesses Intercom
Ringing Assignment 
= All Lines Ring on Stations 10,
17,39, And 41
Line Access Denied 
= None
Toll Tables 
= None Assigned
Origination Denied 
= None
Idle Line Preference 
= None
Night Transfer 
= All Lines Ring On Stations 10,17,39
 And 41
All-Call Receive 
= Enabled...

12. Set ringing line preference.
l 85 (Bl, A5, Bl on LCD Speakerphone)
- enabled
l 84 (Bl, A4, Bl on LCD Speakerphone)
= disabled
13. Select ringing assignments
RINGING
l Press program button C42 (clears previous
settings).
l Choose lines: Al - Al4 = lines 1 - 14
DELAYED RINGING
l Press program button C43 (clears previous
settings).
l Choose lines: Al - Al4 = lines 1 - 14
14. Select Night Transfer (ringing)
l Press program button C44 (clears previous
settings).
l Choose lines: Al - Al4 P lines 1 - 14
15....

22. Specify flexible button/function assignment
(non-square configuration)
3 AND 8 LINE KEYSET LINE ASSIGNMENT
a. Press program button 86 (Bl, A6, Bl on LCD
Speakerphone).
b. Select button to be programmed.Bl
 - B8 (Bl, Al - A8, Bl on LCD
Speakerphone).
c. Select line: Al - Al4 = lines 1 - 14OR-
Press TAP button to disable line appearance.
d. Repeat steps a 
- c for’each line assigned, then
go to step 23.
22 LINEIFEATURE KEYSET LINE ASSIGNMENT
a. Press program button B6 (Bl, A6, Bl on LCD
Speakerphone)....

BLOCK PROGRAMMINGA group of stations can be programmed with the same
COS as a previously programmed station.1. 
PresslTCM*7466
1. Press HOLD HOLD.
2. Specify model station port.
l ClO-C41 -stationponlO-41.
3. Specify first station port.
l ClO-C41 =stationportlO-41.
4. Specify last station port.
l ClO-C41=stationporllO-41.
NOTE: Flexible buttorvfunction assignments for stationpelt
 10 or 11 cannot be changed by block
programming.
5.Press +ff MNTR (SPKR) to end programming.THROUGH-DIALING
WITH AN OPX BOX...

HUNT GROUP PROGRAMMINGStation ports can be assigned to intercom hunt
groups. When a station assigned to a hunt group is
busy, a call to it will ring at the next idle station in the
group. Typical hunt groups operate as follows:
TERMINAL HUNTING
Assume that a terminal hunt group is formed as
follows:
- Station port 013 is linked to station port 014
- Station port 014 is linked to station port 015
- Station port 015 is linked to station port 016.
If station port 013 and 014 are busy when an intercom
call...

5. Choose next station port in link. (Choose first
station port in link if circular link is desired.)
l Cl0 - C41 = station port 10 - 41.
6. Press TAP.
7.Press * and repeat steps 2 - 6 until all station
ports 
are linked as desired.
OR-
Press 
* MNTR (SPKR) to end.
EXAMPLE 1
EXAMPLE 2
(proper link)
(proper links)
To clear a hunt group link,1. 
PresslTCM*7466.
2. Press B8 (Bl, A8, Bl on LCD Speakerphone).
3.Select station port to be unlinked.
l ClO-041 =stationportlO-41.
4.Press 88 (Bl, A8, Bl on LCD...

STATION COS PROGRAMMING REFERENCE TABLE
(Copy this page as required for additional reference sheets)l Shading denotes station default conditions.l Check off or enter values chosen for stations being
programmedIMPORTANT NOTE. To choose B-field programming buttons on 
LCD Speakerphones. pressBl then press Al through A8 to represent B-be/d bunons.
BASELEVEL@aaa@aSTATION ID fREF SYSTEM COS CHART,
STATION PROGRAMMING MODE (B8)POST
ST. T”DE
r
L, 

IMI 66-074COS 
AND SMDR PRINTOUT
COS PRINTOUT
When a data printer is connected to the system, it can
be commanded, from the programming station, to print
the class of service (COS) programming configuration.
Partial or complete printouts can be obtained. When
the printer is being used to obtain a COS printout, the
Station Message Detail 
ecording (SMDR) function is
temporarily halted. SMDR data collection is continued
by the system during 
a COS printout operation;
however, if more than two calls are...

40 COLUMN
PRINTOUT
LINES(SEE NOTE 21
2
1.
2.
2.CARRIAGE RETURN AND LINE FEED IMMEDIATELY
FOLLOW LAST PRINTED CHARACTER ON EACH LINE.ALSO SEE NOTE 2
ILLUSTRATED PRINTOUT IS 40 COLUMN, 
TWOUNEFORMAT. ON 80 COLUMN ONE-UNE PRINTOUT
FORMAT, CARRIAGE RETURN AND LINE FEED
CHARACTERS AT END OF LINE 1 ARE REPLACED BYTWO SPACES FOLLOWED BY ENTIRE CONTENTS OF
LINE 2.
OUfOOlWGCALLMUBTBEOFF-tKXXFOR20SECONDS MINIMUM OR NO RECORDING OCCURS.STATION NUMBER
LINE NUMBER
rANSWER TIME-MINUTES. TENTHS
(INCOMING CALLS...