Comdial Dsu II Non-LCD Telephone Reference Manual

9.6 Response Message Programming
This program lets you set up a button to be used for making a
non-verbal response to a SOHVA or an intercom call. The response
appears in the display of the calling station.
·To assign a button for non-verbal response:
1. PressINTERCOMSS1.
2. Press the programmable button you want to use for
message access.
3. Dial5.
4. Dial a message number (0through9).
NOTE: The preprogrammed messages are created by the
attendant.
5. PressSPEAKERto end.
9.7 Automatic Redial Programming...

9.8 Assist Button Programming
With this feature you can program an “assist” button on your telephone
that will let you send a message to an LCD speakerphone. By pushing
this button you can let a party at another station know, with a tone and a
station message display, that you need assistance with a call.
Then, after receiving the tone and the display message, that person can
join the call or monitor it through executive override or service
observing.
·To program an assist button,
1. PressINTERCOMSS1.
2....

9.10 Subdued Off-Hook Voice Announce
(SOHVA) Button Programming
You can program a button at your station that may be pressed to enable
the delivery of a SOHVA call. With this SOHVA enable button you can
decide, after hearing a busy signal, whether the called party should be
interrupted in a SOHVA manner. If so, you can press the button and
complete the SOHVA call.
·To program a SOHVA button,
1. PressINTERCOMSS1.
2. Press desired programmable button.
3. Dial8.
4. PressSPEAKERto end programming.
9.11 Group...

This page remains blank intentionally. 

Operating Your Telephone
With A DSS/BLF Console
10.1 Operating Your Telephone
With A DSS/BLF Console
The IB24X, IB48X, and IB64X consoles have additional buttons and
status lights that extend the memory button capability of your
telephone. You can program the buttons for automatic dialing (speed
dial) or direct station selection (DSS) with busy lamp field (BLF) using
instructions provided in chapter 9,Programming Your Telephone.
When the installer assigns a DSS/BLF console to a station port, the
system...

10.1.1 Accessing The Button Levels
The IB24X and IB48X DSS/BLF consoles have four levels of buttons,
quadrupling the consoles’ button capacity. The four buttons at the
bottom of each console allow you to select which button level is
currently active. To change button levels, press one of the buttons at the
bottom of the console. The leftmost button activates level 1, the next
button activates level 2, etc. A light beside the appropriate button lights
to indicate which level is currently active. You can...

Troubleshooting
Your Telephone
Should yourImpacttelephone fail to operate properly, or if you do not
understand why it is operating in a certain manner, review the following
list of symptoms and causes for help.
SYMPTOM POSSIBLE CAUSE
INTERCOM light is
flashing.Your messaging is set. Dial
INTERCOM,then#02andhangup.
HOLD or MESSAGE light
is flashing.Another telephone has activated your
message waiting light.
PressINTERCOMand then press
HOLDorMESSAGEto retrieve
message. This action will call the party
who...

This page remains blank intentionally. 

Glossary
A
All-call paging:Paging through the intercoms of all stations in the
system.
Assist button:A button that you can program that will let you send a
message requesting assistance to the LCD of another telephone.
Automatic callback:System will ring a calling telephone when a busy
called telephone becomes idle.
Automatic dialing (or Autodialing):Using programmable buttons to
store numbers for one- or two-button dialing.
Automatic redialing:Turning on a program that automatically redials
the last...

Departmental station operation:The operation of stations that are
organized into departments.
Direct Inward Station Dialing (DISD):This feature allows an outside
party to call an intercom station directly without an attendant’s assistance.
Direct Station Selection/Busy Lamp Field (DSS/BLF):Using one
button to place intercom calls; the button is sometimes referred to as a
DSS button. Busy lamp field or BLF is a term for a light that identifies
current call status of DSS station.
Do not disturb:A mode that...