Comdial Dsu II Digital Telephone System Instructions Manual

SOHVA Tone Burst Quantities
Description:Use this procedure to set the number of SOHVA tone bursts that sounds at the system
stations. You can choose from one to six tone bursts, and the choice that you make here
affects all stations that receive SOHVA calls.
To Program:1. Dial17.“SYSTEM FEATURES ”
2. Dial03.“SOHVA TONES n ”
3. Select the quantity of tone bursts.
—Dial1–6or pressA1–A5, A8(LED On = enabled)
4. DialSfor configuration mode.
5. PressSPEAKERto end.
To change setting, repeat procedure and make...

3.7.24 Service Observing
You can give selected stations the capability to monitor, in an un-announced manner, an active call at
another station.
Assign Service Observing
Description:Select stations to have the service observe feature using this programming.
NOTE:Since this feature requires the executive override feature to function, the
system automatically enables that feature for the station when you enable
service observing.  You can also arrange selected stations so that they cannot
be service...

3.7.25 Station Disable
Description:You can disable station ports on a per station basis.
To Program:1. Dial59.“DISABLE STATIONS”
2. Select station ports to be disabled (LED On = Disabled)
— Station 10–57: Dial10–57or pressC10–C57.
3. DialSfor configuration mode.
To enable station, repeat procedure and make opposite selection.
3.7.26 Station Name
Description:You can assign individual names or category names to stations. These names will then be
displayed by LCD speakerphones when they are called by the...

Character Code Table
Character Code Character Code Character Code
A 21 a 24 Space 12
B22b 25
-15
C23c 26
;17
D31d 34
/18
E32e 35
“19
F33f 36
.27
G41g 44
,28
H42h 45
:29
I 43 i 46 1 01
J 51 j 54 2 02
K 52 k 55 3 03
L 53 l 56 4 04
M 61 m 64 5 05
N 62 n 65 6 06
O 63 o 66 7 07
P 71 p 74 8 08
Q 11 q 14 9 09
R 72 r 75 0 00
S73s 76
T81t 84
U82u 85
V83v 86
W91w 94
X92x 95
Y93y 96
Z13z 16
DSU II Digital Telephone System IMI66–132
Programming The DSU II System  3 – 73 

3.7.27 Station To Station Port Reassignment
Description:Use this procedure to reassign the programming attributes for a station connected to a
particular station port to a different station port (logical to physical reassignment). This
feature allows you to automatically exchange all software attributes for a station (logical
assignment) connected at one station port with those attributes assigned to another station
at a different station port without physically relocating the stations (physical...

3.7.28 System Alarm Report Stations
You can program the system to report any system alarms to designated stations.
Enable Alarm Reporting
Description:If you arrange the system to report alarms, also use this programming feature to enable
stations to display alarm reports after the station user takes appropriate action.
To Program:1. Dial28.“ALARM REPORTS ”
2. PressA1to toggle between enable and disable (LED On = Enable)
—OR—
dial1to enable
dial2to disable.
3. DialSfor configuration mode.
To change...

3.7.29 Voice Announce Blocking
Description:This feature allows a station user to block voice-signaled intercom calls.
To Program:1. Dial53.“STATION FEATURES”
2. Dial04.“VOICE BLOCK”
3. Select station ports (LED On = Selected).
—Station 10–57 = Dial10–57or pressC10-C57.
4. DialSfor next station feature
— OR—
dialSSfor configuration mode.
To clear current setting, repeat procedure.
3.7.30 Block Programming
Description:You can use this station configuration procedure to assign those features that you have...

3.8 Button Mapping The Stations
(Non-Square System Configuration)
You can assign (map) every programmable button at each digital station to be line-select buttons so that
they provide access to outside lines; to be direct station select (DSS) buttons so that they provide quick
access to system stations; to be special purpose buttons so that they provide telephone users with
one-button access to features; or to be idle buttons so that they provide autodial locations for the station
user.
Three idle...

3.8.1 Account Code Button
Description:Press the account code button and then dial an account code to record a call into a
particular category without interrupting the call.
To Program:1. Dial56.“BUTTON MAPPING”
2. Dial17. “ASSIGN ACCT KEY ”
3. Select button to be programmed
—PressA1–A14, B1–B10.
4. Select station ports (LED On = Selected)
—Station 10–57 = Dial10–57or dialC10–C57.
5. DialSfor further ACCOUNT CODE button assignment
—OR—
dialSSfor next button mapping feature
—OR—
dialSSSfor next...

3.8.3 Blank Buttons
Description:Blank those buttons that you want to be dynamic line buttons or autodial buttons.
NOTE:When blanking buttons, be sure a previously assigned button is idle (feature
not selected by user) before you blank it.
To Program:1. Dial56.“BUTTON MAPPING”
2. Dial04.“BLANK/AUTODIAL”
3. Select all buttons to be programmed
—PressA1–A14,B1– B10.
4. Dial #.
5. Select station ports (LED On = Selected).
—Station 10–57 = Dial10–57or pressC10-C57.
6. DialSfor further button blanking
—OR—...