Home > Cisco Systems > Communications System > Cisco Systems Active Voice Repartee Unity R2 4 Installation Guide

Cisco Systems Active Voice Repartee Unity R2 4 Installation Guide

Here you can view all the pages of manual Cisco Systems Active Voice Repartee Unity R2 4 Installation Guide. The Cisco Systems manuals for Communications System are available online for free. You can easily download all the documents as PDF.

Page 121

113
WHAT’S NEXT
You have completed the installation and preliminary setup 
tasks. If you are continuing the Unity setup, see the Unity Sys-
tem Administration Guide to:
Work with the system administrator to make decisions 
about system configuration.
Customize system settings.
Define classes of service.
Add subscribers.
Create distribution lists.
Set up restriction tables.
Set up routing tables.
Back up the system.
Train subscribers.
If ActiveFax was installed as part of the Unity installation,...

Page 122

UNITY INSTALLATION GUIDE114 

Page 123

APPENDIX A
Voice and fax boards5
In this chapter...
Dialogic D/41D  voice board .................................................................................... 116
Dialogic D/41E PCI voice board .............................................................................. 119
Dialogic D/41ESC voice board................................................................................. 121
Dialogic D/41ESC-Euro voice board ...................................................................... 124...

Page 124

UNITY INSTALLATION GUIDE116
Dialogic 
D/41D  
voice board

Switch block SW1Jumpers JP5 and JP6
Side view To p  v i e w
Jumper JP7 Jumper JP1
Voice board backplate Connection pinouts
The D/41D uses 
RJ-14 connectors.
Lines 1 & 2
Lines 3 & 4
Pin 1: Second port tip
Pin 2: First port tip
Pin 3: First port ring
Pin 4: Second port ring 

Page 125

APPPENDIX A: Voice and fax boards117
Hardware settings
Do the following procedures as you install voice boards.
To set switch block SW1 and jumpers JP5, JP6, 
and JP7
The switch block SW1 and jumper JP6 settings identify the voice 
board’s memory address, which in turn specifies which voice 
messaging ports are on which board. The jumper JP7 setting 
specifies which board is in the first slot.
aSet SW1 switches on each board:
Turnkey systemSet SW1 switches as shown below.
Component systemSet SW1 switches...

Page 126

UNITY INSTALLATION GUIDE118
Dialogic D/41D  
Continued
voice boardSoftware settingsDuring Unity Setup, do the following procedure when the Dia-
logic Board Configuration dialog box appears.
To enter Dialogic settings during Unity Setup
aChange the value of “Number of boards” to the number of 
Dialogic D/41D boards in the server.
bChange the value of “IRQ” to “5.”
cIn the Board Addresses list, select one address for each 
D/41D board in the server:
Turnkey systemStart with “0xD0000” and select consecu-...

Page 127

APPPENDIX A: Voice and fax boards119
Dialogic 
D/41E PCI 
voice board
Continued
Jumpers
JP2–JP5Jumpers 
JP6–JP7Switch
SW1Switch 
SW2
Voice board backplate
Line 1
Line 2
Connection pinouts
The D/41E PCI uses 
RJ-11 connectors.
Line 3
Line 4
Side view
Pin 4: Unused Pin 3: Ring Pin 2: Tip
Pin 1: Unused 

Page 128

UNITY INSTALLATION GUIDE120
Dialogic D/41E PCI 
Continued
voice boardHardware settingsDo the following procedures as you install voice boards.
To  s e t  t h e  S W 1  s w i t c h
For each Dialogic PCI voice board that has a rotary switch, 
set the rotary switch to a unique value starting with 1 and 
continuing in sequence.
For example, set the rotary switch on the first three PCI 
voice boards in the Unity server as shown below. This is also 
the order in which you install the boards in the server. 
To...

Page 129

APPPENDIX A: Voice and fax boards121
Dialogic 
D/41ESC 
voice board
Continued
0
Vo i c e  b oa r d  b a c k p l a t e
SC bus connector Switch SW1 Switch block SW2
To p  v i e w
Side view
Pin 4: Unused
Connection pinouts
The D/41ESC uses 
RJ-11 connectors.
Line 1
Line 2
Line 3
Line 4
Pin 1: Unused
Pin 2: Tip
Pin 3: Ring 

Page 130

UNITY INSTALLATION GUIDE122
Dialogic D/41ESC 
Continued
voice boardHardware settingsDo the following procedures as you install voice boards.
To  s e t  t h e  S W 1  s w i t c h
For each Dialogic ISA voice board that has a rotary switch, 
set the rotary switch to a unique value starting with 0 and 
continuing in sequence. 
For example, set the rotary switch on the first three ISA 
voice boards in the Unity server as shown below. This is also 
the order in which you install the boards in the server. 
To...
Start reading Cisco Systems Active Voice Repartee Unity R2 4 Installation Guide

Related Manuals for Cisco Systems Active Voice Repartee Unity R2 4 Installation Guide

All Cisco Systems manuals