Cisco Systems Active Voice Repartee Unity R2 4 Installation Guide

APPPENDIX A: Voice and fax boards143
Hardware settings
Do the following procedure as you install fax boards.
WARNING!Do not remove the cover from the server or expansion 
chassis while the power is on, if a CPD/220 fax board is already 
installed. The voltage level from the board can cause injury.
WARNING!Never connect a loop-start phone line to a DID fax 
port. The voltage in the loop-start line will damage the fax board. If 
you are unsure whether the line is a loop-start line, test it with a 
volt...

UNITY INSTALLATION GUIDE144
Dialogic 
GammaLink 
CPi/200 
fax boardLED status indicators
Fax board backplate
Pin 3: First fax line tip Pin 2: First fax line ring
Connection pinouts
The CPi/200 uses an 
RJ-14 connector.
Lines 1 & 2
Pin 1: Second fax line tip
Pin 4: Second fax line ring
Switch block SW1Side view 

APPPENDIX A: Voice and fax boards145
Hardware settings
Do the following procedure as you install fax boards.
To  s e t  s w i t c h  b l o c k  S W 1
The switch block SW1 settings determine the fax ports’ I/O 
addresses.
The CPi/200 board contains two fax ports. Depending on the 
configuration of the Unity server, you can install up to two 
CPi/200 boards.
Set the SW1 switches on each board as shown below.
LED status indicators
There are two LED status indicators for each fax port. The fol-
lowing table...

UNITY INSTALLATION GUIDE146
Dialogic 
GammaLink 
CPi/200 PCI 
fax board
LED status indicators
Fax board backplate
Pin 3: First fax line tip Pin 2: First fax line ring
Connection pinouts
The CPi/200 PCI uses 
an RJ-11 connector.
Lines 1 & 2
Pin 1: Second fax line tip
Pin 4: Second fax line ringRotary switch
Side view To p  v i e w 

APPPENDIX A: Voice and fax boards147
Hardware settings
Do the following procedure as you install fax boards.
To set the rotary switch
The rotary switch setting identifies the fax board and specifies 
which fax ports are on which board. 
The CPi/200 PCI board contains two fax ports. Depending on the 
configuration of the Unity server, you can install up to four 
CPi/200 PCI boards.
Set the rotary switch on each board as shown below.
LED status indicators 
There are two LED status indicators for each fax...

UNITY INSTALLATION GUIDE148
Dialogic 
GammaLink 
CPi/400 PCI 
fax board
LED status indicators
Pin 3: First fax line tip Pin 2: First fax line ring
Connection pinouts
The CPi/400 PCI uses 
RJ-11 connectors.
Pin 1: Second fax line tip
Pin 4: Second fax line ringRotar y switch
Pin 3: Third fax line tip Pin 2: Third fax line ring
Pin 1: Fourth fax line tip
Pin 4: Fourth fax line ring
Fax board backplate
Lines 3 & 4
Lines 1 & 2
Side view To p  v i e w 

APPPENDIX A: Voice and fax boards149
Hardware settings
Do the following procedure as you install fax boards.
To set the rotary switch
The rotary switch setting identifies the fax board and specifies 
which fax ports are on which board. 
The CPi/400 PCI board contains four fax ports. Depending on 
the configuration of the Unity server, you can install up to eight 
CPi/400 PCI boards.
Set the rotary switch on each board as shown below.
LED status indicators
There are two LED status indicators for each fax...

UNITY INSTALLATION GUIDE150
Natural 
MicroSystems 
AG 2000 
voice and fax 
boardSwitch SW1H.100 bus connector
Voice boar d b ac kp la te
Lines 1 & 2
Lines 3 & 4
Lines 7 & 8
Pin 1: Not used
Pin 2: Tip 2
Pin 3: Ring 1
Pin 4: Tip 1
Pin 5: Ring 2
Pin 6: Not used
Connection pinouts
The AG 2000 uses 
RJ-14 connectors.
Lines 5 & 6
Side view 

APPPENDIX A: Voice and fax boards151
Using AG 2000 boards
AG 2000 boards can be used for both voice and fax ports. 
The number of ports that are dedicated to fax is determined by 
the Unity system key. If you want more or fewer fax ports, you 
must upgrade the system key. For more information, see “Sys-
tem key upgrades,” on page 112.
A fax port can only send and receive faxes. It cannot answer 
voice calls.
If the AG 2000 boards are used for both voice and fax, voice 
ports are assigned first, beginning...

UNITY INSTALLATION GUIDE152
Natural 
MicroSystems 
AG 2000 
Continued
voice and fax boardHardware settings
Do the following procedure as you install voice boards.
To set the DIP switch that controls H.100 bus 
termination
The setting on the DIP switch on the AG 2000 board depends on 
how many boards you are installing:
One board  Set all switches to “Off.”
Two boar ds  Set all switches on both boards to “On.”
Three or more boards  Set all switches on the first and last 
boards to “On,” and set all...