Cisco Systems Active Voice Repartee Unity R2 4 Installation Guide

APPPENDIX A: Voice and fax boards153
Software settings
During Unity Setup, do the following procedure when the NMS 
Country Selection dialog box appears. 
To enter AG 2000 settings during Unity Setup
aSelect a country.
bClick “OK” to continue. 
cWhen the NMS Configurator dialog box appears, click “OK” 
to close it. 
dReturn to the procedure that you were doing when the NMS 
Country Selection dialog box appeared. 

UNITY INSTALLATION GUIDE154
Natural 
MicroSystems 
AG-T1 
voice board

	


I/O address DIP switch
T1 trunk interfaceSide view
Pin 1: R – Receive from network
Pin 2: T – Receive from network
Pin 3: No connection
Pin 4: R1 – Transmit to network
Pin 5: T1 – Transmit to network
Pin 6: No connection
Pin 7: Optional shield (not used)
Pin 8: Optional shield (not used)
Voice board 
backplate Connection pinouts
The AG-T1 uses an RJ-48C connector.
LED status
indicators
T1 trunk
interface 

APPPENDIX A: Voice and fax boards155
Hardware settings
Do the following procedure as you install voice boards.
To set the I/O address DIP switch
Use these settings as you install the AG-T1 voice boards accord-
ing to the Natural MicroSystems documentation.
Set the I/O address DIP switch on each board as shown 
below.
Software settings
During Unity Setup, do the following procedure when the NMS 
Configurator dialog box appears. 
To enter AG-T1 settings during Unity Setup
aSelect a country.
bChange the...

UNITY INSTALLATION GUIDE156
Natural 
MicroSystems AG-T1 
Continued
voice board
gThe value you specify in the Protocol list depends on the 
type of phone system you are connecting the Unity server to.
hIn the ISA section, in the Address list, click the I/O address 
that matches the DIP switch setting for this board. For a list 
of settings, see “To set the I/O address DIP switch,” on 
page 155.
iClick “OK” to close the Configure Board dialog box. The NMS 
Configurator dialog box reappears. 
jTo add more...

APPPENDIX A: Voice and fax boards157
Natural 
MicroSystems 
AG Dual T1 
voice board
Continued
Side view
Pin 1: R – Receive from network
Pin 2: T – Receive from network
Pin 3: No connection
Pin 4: R1 – Transmit to network
Pin 5: T1 – Transmit to network
Pin 6: No connection
Pin 7: Optional shield (not used)
Pin 8: Optional shield (not used)
Voice board 
backplate Connection pinouts
The AG-T1 uses RJ-48C connectors.
LED status
indicators
T1 trunk
interface
H.100 bus connector 

UNITY INSTALLATION GUIDE158
Natural 
MicroSystems AG 
Continued
Dual T1 voice boardHardware settingsNone.
Software settings
During Unity Setup, do the following procedure when the NMS 
Configurator dialog box appears. 
To enter AG Dual T1 settings during Unity setup
aSelect a country.
bSelect the first board in the list.
cClick “Configure board.” The Configure Board dialog box 
appears.
dIn the Board Type list, confirm that the value is “AG Dual 
T1.”
eIn the TAPI Lines list, confirm that the value is...

APPPENDIX A: Voice and fax boards159
lClick “OK” to close the Configure Board dialog box. The NMS 
Configurator dialog box reappears.
mIf more than one AG Dual T1 board is installed, select the 
next board in the list of boards, and repeat steps c 
throughl for each board.
nIf the Unity server also contains AG-T1 boards, do the proce-
dure “To enter AG-T1 settings during Unity Setup,” on 
page 155. 
Otherwise, click “OK” to close the NMS Configurator dialog 
box, and return to the procedure that you were...

UNITY INSTALLATION GUIDE160
Voice 
Technologies 
Group 
VoiceBridge 
2000 
feature-set 
board
Side view To p  v i e w
SC bus connector
Voice board backplate 

APPPENDIX A: Voice and fax boards161
Use the Voice Technologies Group VoiceBridge 2000 feature-set 
board with the Dialogic D/160SC voice board to provide fea-
ture-set integration on Mitel SX-200 and SX-2000 phone sys-
tems.
All of the D/160SC and VoiceBridge 2000 boards that you are 
installing must be in the same box because they all must be con-
nected with an SC bus cable. If there are not enough slots in the 
Unity server, then you must put all of the boards into an expan-
sion chassis.
Hardware...

UNITY INSTALLATION GUIDE162
Voice Technologies 
Group VoiceBridge 
2000 feature-set 
Continued
board
fClick the Bus Settings tab.
gIf this is board number 1, click “Master.” 
If this is any other board, click “Slave.”
hTo accept the settings for the board, click “OK.” 
iIf more than one VoiceBridge board is installed, click the 
next board in the list of installed VoiceBridge 2000 boards, 
and repeat steps c throughh.
jTo save the configuration, click “Save” on the File menu.
kOn the VoiceBridge 2000...