Cisco 6500e Manual

1-63
Catalyst 6500 Series Switches Installation Guide
OL-5781-08
Chapter 1      Removal and Replacement Procedures
  Removing and Installing the DC-Input Power Supplies
Figure 1-44 Handling a DC-Input Power Supply without IPM
Figure 1-45 Handling a DC-Input Power Supply with IPM
191308
RUNINSTALL
CISCO SYSTEMS, INC1
2
34
INPUT OKFAN
OKOUTPUT
FAIL
RUNINSTALL
CISCO SYSTEMS, INC1
2
34
INPUT OKFAN
OKOUTPUT
FAIL 

1-64
Catalyst 6500 Series Switches Installation Guide
OL-5781-08
Chapter 1      Removal and Replacement Procedures
  Removing and Installing the DC-Input Power Supplies
Installing a 6000 W DC-Input Power Supply
NoteWith the PWR-6000-DC power supply, you have the option of installing an Input Power Module (IPM) 
(previously removed) with the DC-input wires and the ground wires still connected. You can then install 
your power supply and insert the fully-wired IPM. Read through this procedure carefully...

1-65
Catalyst 6500 Series Switches Installation Guide
OL-5781-08
Chapter 1      Removal and Replacement Procedures
  Removing and Installing the DC-Input Power Supplies
NoteYou should allow a minimum of 2.5 to 3 inches (63.5 mm to 76.2 mm) of space between the side of the 
power supply and any obstructions (such as the side of an enclosed equipment rack). This space is needed 
to install and secure the DC-input power cables correctly. Incorrectly routing the DC-input power cables 
can cause airflow...

1-66
Catalyst 6500 Series Switches Installation Guide
OL-5781-08
Chapter 1      Removal and Replacement Procedures
  Removing and Installing the DC-Input Power Supplies
Figure 1-47 6000 W DC-Input Power Supply Front Panel
WarningPower supply captive installation screws must be tight to ensure protective grounding continuity. 
Statement 289
NoteWith the PWR-6000-DC power supply, you have the option of installing an Input Power Module 
(IPM) (previously removed) with the DC-input wires and the ground wires...

1-67
Catalyst 6500 Series Switches Installation Guide
OL-5781-08
Chapter 1      Removal and Replacement Procedures
  Removing and Installing the DC-Input Power Supplies
Step 4Remove the two A4 screws securing the outer terminal block cover, and remove the cover from the power 
supply (Figure 1-47).
Step 5Attach the appropriate lugs to the DC-input wires and ground wire. The wires should be sized according 
to local and national installation requirements. Use only copper wire.
Note6000 W power supplies...

1-68
Catalyst 6500 Series Switches Installation Guide
OL-5781-08
Chapter 1      Removal and Replacement Procedures
  Removing and Installing the DC-Input Power Supplies
Step 6Wire for 2800 W (left side of power supply bay) as follows:
a.From the left side of the power supply, connect the ground wire to the ground (Figure 1-48).
Figure 1-48 DC-Input Wire Connections for 2700-W DC-Input Power Supply for Left Side of Power 
Bay
b.
From the left side of the power supply, connect each of the DC-input wires to...

1-69
Catalyst 6500 Series Switches Installation Guide
OL-5781-08
Chapter 1      Removal and Replacement Procedures
  Removing and Installing the DC-Input Power Supplies
Figure 1-49 DC-Input Wire Connections for 4000-W DC-Input Power Supply for Left Side of Power 
Bay
b.
From the left side of the power supply, connect each of the DC-input wires to the terminal block in 
this order (see Figure 1-47 and Figure 1-49): 
Negative (-) 
Positive (+) 
NoteWhen you tighten the terminal nuts, make sure they are...

1-70
Catalyst 6500 Series Switches Installation Guide
OL-5781-08
Chapter 1      Removal and Replacement Procedures
  Removing and Installing the DC-Input Power Supplies
Figure 1-50 DC-Input Wire Connections for 6000-W DC-Input Power Supply for Left Side of Power 
Bay
b.
From the left side of the power supply, connect each of the DC-input wires to the terminal block in 
this order (see Figure 1-47 and Figure 1-50):
Negative (-) 
Positive (+) 
NoteWhen you tighten the terminal nuts, make sure they are...

1-71
Catalyst 6500 Series Switches Installation Guide
OL-5781-08
Chapter 1      Removal and Replacement Procedures
  Removing and Installing the DC-Input Power Supplies
Figure 1-51 DC-Input Wire Connections for 2700-W DC-Input Power Supply, Right Side of Power 
Bay
b.
From the right side of the power supply, connect the DC-input wires to the terminal block (see 
Figure 1-47 and Figure 1-51) in this order:
Negative (-) 
Positive (+) 
NoteWhen you tighten the terminal nuts, make sure they are snug. Do not...

1-72
Catalyst 6500 Series Switches Installation Guide
OL-5781-08
Chapter 1      Removal and Replacement Procedures
  Removing and Installing the DC-Input Power Supplies
NoteFor multiple DC input power supply, each DC input must be protected by dedicated circuit 
breaker or fuse. The circuit breaker or fuse should be sized according to the power supply input 
rating and local or national electrical code requirements.
Step 10Wire for 4500 W (right side of power supply bay) as follows:
a.From the right side...