Cisco 6500e Manual

1-13
Catalyst 6500 Series Switches Installation Guide
OL-5781-08
Chapter 1      Removal and Replacement Procedures
  Removing and Installing the AC-Input Power Supplies
Installing the 1000 W, 1300 W, 2500 W, 3000 W, 4000 W, 6000 W, and 8700 W AC-Input Power 
Supplies
CautionUse both hands to install and remove power supplies. Each Catalyst 6500 series AC-input power supply 
weighs between 14.5 pounds (6.6 kg) and 40 pounds (18.14 kg).
To install an AC-input power supply, follow these steps:
Step 1Ensure...

1-14
Catalyst 6500 Series Switches Installation Guide
OL-5781-08
Chapter 1      Removal and Replacement Procedures
  Removing and Installing the AC-Input Power Supplies
Step 9Connect the other end of the power cord to an AC-input power source.
CautionIn a chassis with dual power supplies or power supplies with multiple AC inputs, connect each AC power 
cord to a separate input source. In case of a power source failure, the alternate input source should still 
be available.
Step 10On 8700 W power...

1-15
Catalyst 6500 Series Switches Installation Guide
OL-5781-08
Chapter 1      Removal and Replacement Procedures
  Removing and Installing the DC-Input Power Supplies
Removing and Installing the DC-Input Power Supplies
This section covers the DC-input power supply removal and installation procedure for the Catalyst 6500 
series switches and is divided into the following topics:
Removing and Installing a 950 W DC-Input Power Supply, page 1-15
Removing and Installing a 1300 W or 2500 W DC-Input Power...

1-16
Catalyst 6500 Series Switches Installation Guide
OL-5781-08
Chapter 1      Removal and Replacement Procedures
  Removing and Installing the DC-Input Power Supplies
Removing a 950 W DC-Input Power Supply
WarningBefore performing any of the following procedures, ensure that power is removed from the DC 
circuits. To ensure that all power is removed, locate the circuit breakers or fuses on the DC power 
lines that service the DC circuits. Turn OFF the DC power line circuit breakers and remove the DC...

1-17
Catalyst 6500 Series Switches Installation Guide
OL-5781-08
Chapter 1      Removal and Replacement Procedures
  Removing and Installing the DC-Input Power Supplies
Figure 1-9 950 W DC-Input Power Supply Captive Installation Screws
Figure 1-10 Catalyst 6503 Switch—Handling a DC-Input Power Supply
63183
INPUT
OKFA N
OKOUT
PUT
FAIL
Captive installation screws
Status LEDs
63032
IN
PUT
O
KF
AN
OKO
UTPUT
F
AIL
INP
UT
O
KFA
N
OKOUTPU
T
FAILPower Supply 2
(redundant)
Power
Supply 1 

1-18
Catalyst 6500 Series Switches Installation Guide
OL-5781-08
Chapter 1      Removal and Replacement Procedures
  Removing and Installing the DC-Input Power Supplies
Installing a 950 W DC-Input Power Supply
WarningBefore performing any of the following procedures, ensure that power is removed from the DC 
circuits. To ensure that all power is removed, locate the circuit breakers or fuses on the DC power 
lines that service the DC circuits. Turn OFF the DC power line circuit breakers and remove the DC...

1-19
Catalyst 6500 Series Switches Installation Guide
OL-5781-08
Chapter 1      Removal and Replacement Procedures
  Removing and Installing the DC-Input Power Supplies
Removing and Installing a 1300 W or 2500 W DC-Input Power Supply
This section covers the power supply removal and installation procedures for the 1300 W and the 
2500 W DC-input power supplies and is divided into the following topics:
Required Tools, page 1-19
Removing a 1300 W or 2500 W DC-Input Power Supply, page 1-19
Installing a 1300...

1-20
Catalyst 6500 Series Switches Installation Guide
OL-5781-08
Chapter 1      Removal and Replacement Procedures
  Removing and Installing the DC-Input Power Supplies
Step 4Disconnect the source DC cable lugs from the terminal block (see Figure 1-13 for the 1300 W DC power 
supply or Figure 1-14 for the 2500 W DC power supply) in this order:
1.Positive (+)
2.Negative (–)
3.Ground
NoteThe terminals on the 1300 W DC power supply DC power cable terminal block are labeled (from 
top to bottom) +, –,...

1-21
Catalyst 6500 Series Switches Installation Guide
OL-5781-08
Chapter 1      Removal and Replacement Procedures
  Removing and Installing the DC-Input Power Supplies
Figure 1-12 DC-Input Power Supply Front Panel (WS-CDC-2500W)
Figure 1-13 DC-Input Wire Connections on the Terminal Block (WS-CDC-1300W)
INPUT
OKFA N
OKOUTPUT
FA I L
I
0
85906
Power
switch DC power cable
terminal blockTerminal block
cover
Status LEDs
Captive installation
screw
INPUT
OKFA N
OKOUTPUT
FAIL
I
0
18736
Power leads attached
to...

1-22
Catalyst 6500 Series Switches Installation Guide
OL-5781-08
Chapter 1      Removal and Replacement Procedures
  Removing and Installing the DC-Input Power Supplies
Figure 1-14 DC-Input Wire Connections on the Terminal Block (WS-CDC-2500W)
INPUT
OKFA N
OKOUTPUT
FA I L
I
0
85907
Power leads
attached to
terminal block
( - )  Negative
(+)   Positive
(   )  Ground
Captive 
installation
screw
Power
switch
DC-input cable