Cisco 6500e Manual

1-3
Catalyst 6500 Series Switches Installation Guide
OL-5781-08
Chapter 1      Removal and Replacement Procedures
  Removing and Installing the AC-Input Power Supplies
NoteThe following power supply restrictions exist for the Catalyst 6500 series chassis:
The 6000 W and the 8700 W power supplies are limited to 4000 W when they are installed in the 
Catalyst 6506, Catalyst 6509, and Catalyst 6509-NEB chassis. 
The 8700 W power supply is limited to 4500 W when it is installed in a Catalyst 6509-NEB-A...

1-4
Catalyst 6500 Series Switches Installation Guide
OL-5781-08
Chapter 1      Removal and Replacement Procedures
  Removing and Installing the AC-Input Power Supplies
To remove a power supply, follow these steps:
Step 1Turn the power switch to the Off (0) position on the PEM for the power supply that you are removing. 
Figure 1-1 shows the location of the AC-input PEMs on the Catalyst 6503 and Catalyst 6503-E switch 
chassis. 
Step 2Disconnect the power cord from the power source. Do not touch the metal...

1-5
Catalyst 6500 Series Switches Installation Guide
OL-5781-08
Chapter 1      Removal and Replacement Procedures
  Removing and Installing the AC-Input Power Supplies
Figure 1-3 Handling an AC-Input Power Supply
Installing a 950 W or 1400 W AC-Input Power Supply
To install an AC-input power supply, follow these steps:
Step 1Ensure that the system (earth) ground connection has been made. 
For ground connection instructions, see the “Establishing the System Ground” section on page 1-52.
Step 2If...

1-6
Catalyst 6500 Series Switches Installation Guide
OL-5781-08
Chapter 1      Removal and Replacement Procedures
  Removing and Installing the AC-Input Power Supplies
Step 6Connect the other end of the power cord to an AC-input power source.
CautionIn a system with dual power supplies, connect each power supply to a separate input source. In case 
of a power source failure, the second source should still be available.
Step 7Turn the PEM power switch to the On (|) position.
Step 8Verify the power supply...

1-7
Catalyst 6500 Series Switches Installation Guide
OL-5781-08
Chapter 1      Removal and Replacement Procedures
  Removing and Installing the AC-Input Power Supplies
Removing a 2700 W AC-Input Power Supply
To remove a 2700 W AC-input power supply, follow these steps:
Step 1Turn the power switch to the off (0) position on the power supply you are removing. 
Step 2Disconnect the power cord from the power source. Do not touch the metal prongs on the power cord 
while it is still connected to the power...

1-8
Catalyst 6500 Series Switches Installation Guide
OL-5781-08
Chapter 1      Removal and Replacement Procedures
  Removing and Installing the AC-Input Power Supplies
Figure 1-5 Handling a 2700 W AC-Input Power Supply
Step 6
If the power supply bay is to remain empty, install a blank power supply filler plate (Cisco 
part number 800-16727-01) over the opening and secure it with the captive installation screws. 
Installing a 2700 W AC-Input Power Supply
WarningThis product requires short-circuit...

1-9
Catalyst 6500 Series Switches Installation Guide
OL-5781-08
Chapter 1      Removal and Replacement Procedures
  Removing and Installing the AC-Input Power Supplies
Step 6Plug the power cord into the power supply AC-in receptacle.
Step 7Connect the other end of the power cord to the AC-input power source.
CautionIn a system with dual power supplies, connect each power supply to a separate source circuit. In case of 
a power source failure, the second source will most likely still be available.
Step...

1-10
Catalyst 6500 Series Switches Installation Guide
OL-5781-08
Chapter 1      Removal and Replacement Procedures
  Removing and Installing the AC-Input Power Supplies
Removing the 1000 W, 1300 W, 2500 W, 3000 W, 4000 W, 6000 W, and 8700 W AC-Input Power 
Supplies
WarningHazardous voltage or energy is present on the backplane when the system is operating. Use caution 
when servicing. Statement 1034
To remove an AC-input power supply, follow these steps:
Step 1Turn the power switch to the off (0)...

1-11
Catalyst 6500 Series Switches Installation Guide
OL-5781-08
Chapter 1      Removal and Replacement Procedures
  Removing and Installing the AC-Input Power Supplies
Figure 1-6 AC-Input Power Supply Front Panel
Step 6
Grasp the power supply handle with one hand, and slide the power supply part of the way out of the 
chassis. Place your other hand underneath the power supply, as shown in Figure 1-7, and slide the power 
supply completely out of the chassis.
Step 7If the power supply bay is to remain...

1-12
Catalyst 6500 Series Switches Installation Guide
OL-5781-08
Chapter 1      Removal and Replacement Procedures
  Removing and Installing the AC-Input Power Supplies
Figure 1-7 Handling an AC-Input Power Supply
48133
FA N
S TAT US
1
2
3
4
5
6
7
8
9
8 PORT GIGABIT ETHERNET
WS-X64081LIN
KSTATUS2
3
4
5
6
7
8L
IN
KLINKLINKLIN
KLINKLINKLIN
K
8 PORT GIGABIT ETHERNET
WS-X64081LINKSTATUS2
3
4
5
6
7
8LINKLIN
KLINKLINKLIN
KLINKLINK
8 PORT GIGABIT ETHERNET
WS-X64081LINKSTATUS2
3
4
5
6
7
8LIN
KLINKLINKLINKLIN...