Christie Projector Mirage WU-L User Manual

							Mirage WU-L User ManualA-1020-100774-01 Rev. 2 (4-2012)
A Interconnect Drawing 
						

							                                                                                                                                                                                                                                                                       Appendix A: Interconnect Drawing
Mirage WU-L User ManualA-1
020-100774-01 Rev. 2 (4-2012)A.1 INTERCONNECT DRAWING 
						

							Mirage WU-L User ManualB-1020-100774-01 Rev. 2 (4-2012)
Appendix B: Web User Interface
B.1 Logging On
IMPORTANT: Before logging on to the system, ensure that you select the appropriate language 
required. Your language selection only affects the web user interface. The language used by the 
projector’s on-screen display (OSD) is not affected. See Figure B-1. 
1. Open your web browser and type the IP address (in the address bar) assigned to your projector.
2. Select the appropriate language from the Language drop-down list, located in the upper left-hand 
corner. See Figure B-1.
3. Type your user name and password in the User Name and Password (see Figure B-2) fields 
respectively. Both entries are case-sensitive.
4. Click the Login button. The Main window (see Figure B-3) appears.
Figure B-3 Main window Figure B-1 Language drop-down list Figure B-2 Login
A
C
B
D
GH
I
J
K
EF 
						

							B-2Mirage WU-L User Manual020-100774-01 Rev. 2 (4-2012)
Appendix B: Web User Interface
The following table describes each area found in the Main window. See Figure B-3.
B.2 Navigating the Web User Interface
NOTICE: Internet Explorer V6.0 has known performance issues and is not recommended to be used as the 
primary web browser for the web user interface. It is recommended that you use Internet Explorer V7.0.
It is not recommended that you use the web browser’s navigation functionality (i.e. the Back and Forward 
functions) as this will cause you to lose your web connection. It is recommended that you navigate using the 
application interface and related functionality detailed in this section.
B.2.1 Help Text
You can move your mouse pointer over most buttons or 
fields to display related help information. See Figure B-4. 
To disable this feature, click Admin > System > To o l t i p :  
Hide. NOTE: Help text is not available for a disabled 
buttons.
When working with the projector menu system on the Tools 
tab, highlight the menu option and press “h”.
ASecondary Tabs (specific to a 
primary tab) located along the 
bottom of the Main window.BSecondary Input Active Input 
Window and Main Active 
Input Window sections are 
read-only.CThese sections provide drop-
down list selections (refer to 
Section 3, Operation for more 
details).
DPrimary Tabs located along the 
top of the Main window.ECurrent Status Bar provides 
information messages according 
to the current status of the 
projector.FProjector Information section 
is read-only.
GStatus Indicator displays the 
overall status of the projector, 
based on the 12 categories of 
information available. NOTE: 
Click the Status Indicator LED 
to display the Sta tus window 
and obtain more information 
about any current errors and 
warnings. See Section B.3.2 
Main Tab - Status.HLogout button (located at the top 
right corner of the web browser) 
is used to logout you off of the 
web user interface and the 
projector. IPower section contains an On 
and Off button. Only one is 
enabled depending on the 
current powered state of the 
projector.
JShutter section contains an 
Open and Close button. Only 
one is enabled depending on the 
current state of the projector’s 
shutter.KOSD (On Screen Display) 
section contains an On and Off 
button. Only one is enabled 
depending on the current state of 
the projector’s on-screen display.
Figure B-4 Help Mouse Over Example 
						

							Appendix B: Web User Interface
Mirage WU-L User ManualB-3020-100774-01 Rev. 2 (4-2012)
B.3 Basic Operation
This section discusses the primary tabs located along the top of the application window. Each primary tab also 
has related secondary tabs which are located along the bottom of each tab as follows:
B.3.1 Main Tab - General
Under the Main tab, select the General secondary tab to view general information about Inputs, Channels, 
Projector Information, Test Pattern, and Color Enable (see Figure B-3). For detailed information refer to 
Section 3 Operation.
B.3.2 Main Tab - Status 
Under the Main tab, select the Sta tus secondary tab to view the 12 Category LED status lights which indicate 
the projector’s highest critical state. See Figure B-5. The LED color of the category indicates that it is in one of 
the following states:
• Green = Good
• Yellow = Warning
• Red = Error
For more information about each LED, click an LED button for details.
Figure B-5 Category Status Example
Main
• General
• StatusTo o l s
• Virtual OSDAdmin
•System
• UsersAbout
•Version
•License 
						

							B-4Mirage WU-L User Manual020-100774-01 Rev. 2 (4-2012)
Appendix B: Web User Interface
B.3.3 Tools Tab - Virtual OSD 
The To o l s tab defaults to the Virtual OSD secondary tab. See Figure B-6.
Figure B-6 Tools Window
 The following table describes each area found in the To o l s window. See Figure B-6.
AVirtual OSD tab presents the 
Main Menu (refer to Appendix 
A, Menu Tree for more details).BThe Maximize/Minimize button 
toggles depending on the current 
state of the projector. When 
maximized, the Virtual OSD 
displays over the entire page so 
that subsequent menus can be 
viewed without scrolling. No 
access to tabs when maximized.CHelp button presents a pop-up 
window which provides 
information to help you navigate 
within the current menu.
DOSD section contains an On and 
Off button. Only one is enabled 
depending on the current state of 
the OSD. Control of the OSD is 
always available through the 
remote.EAuto Setup button uses the 
manufacture’s default settings 
(refer to Section 3, Operation for 
more details).
A
B
C
D
E 
						

							Appendix B: Web User Interface
Mirage WU-L User ManualB-5020-100774-01 Rev. 2 (4-2012)
Virtual OSD Menu
Selecting an option from a menu displays its associated 
window, showing related information and input fields. To 
return to the previous menu, click the menu’s title bar (see 
Figure B-7). 
To return to a previous menu, click on the current menu’s title 
bar or press ESC. NOTE:
 Click the Maximize button to view 
the full screen size.
Various types of menu elements (Figure B-8 and Figure B-9) 
allow you to define projector settings. 
These include:
• Field entries
• Drop-down lists
• Check boxes
• Sliders
NOTE: When a menu option is modified through the Virtual OSD menu, the projector setting takes effect 
immediately.
Entering a number in a numeric field
1. Position your mouse pointer within the numeric field that you wish to edit.
2. Click to highlight the field entry. NOTE: If you click the menu option, the field cannot be edited.
3. Edit the field entry.
4. Press Enter to save your changes.
Figure B-8 Select Numeric Field
Figure B-7  View Previous Menu 
						

							B-6Mirage WU-L User Manual020-100774-01 Rev. 2 (4-2012)
Appendix B: Web User Interface
Selecting an option from a drop-down list
1. Click the option drop-down arrow to open the drop-down list. 
2. Locate and select the desired option.
Figure B-9 Types of Menu Elements
Selecting or clearing a check box
To select or clear a check box, click the check box with your mouse pointer. This enables or clears the option 
respectively.
Clock setting
1. Click within the field (i.e. Lamp Regeneration Start Time option) to allow access.
2. Change the Hour, Minute, and Seconds fields (double-digit field entry) as required. 
Figure B-10 Dates 
						

							Appendix B: Web User Interface
Mirage WU-L User ManualB-7020-100774-01 Rev. 2 (4-2012)
B.3.4 Admin Tab - System
Under the Admin tab, select the System secondary tab to upgrade, upload, backup and restore specific files, 
change the Logo position, background color, gamma properties, and interrogate the projector (creating a zip 
file of information).
Figure B-11 Admin window
The following table describes each area found in the Admin window. See Figure B-11.
ARestore section allows you 
to select the file and file type 
that you wish to restore. BBackup section allows you 
to select the file and file type 
that you wish to backup.C Upload section allows you to 
select the file and file type that 
you wish to upload.
DLogo Position and 
Background Color section 
is enabled when you select a 
Logo file type from the 
Upload section.EGamma Properties section 
is enabled when you select a 
Gamma file type from the 
Upload section. FSync button is used to set the 
projector date and time to 
match that on your computer.
GUpload, Backup, Restore, 
and Interrogator buttons 
perform their respective 
functions, after the setting for 
the function have first been 
selected from the drop-down 
lists, and other fields on the 
left. HUpgrade button, refer to the 
Visual Environments 
Projector Software Upgrade 
instruction sheet, P/N 020-
100443-xx. This button is 
disabled if the projector is 
not in Standby mode.IHide button allows you to 
disable the display of the help 
text.
A
C
B
DEF
I
H
G