Christie Projector Mirage WU-L User Manual

Section 3: Operation
Mirage WU-L User Manual3-63020-100774-01 Rev. 2 (4-2012)
Connecting One Stereo 3D Sync Output 
Connect the GPIO 3D Stereo Sync Cable output to your stereo 3D sync emitter or 3D passive filter system, 
PZE device. The L/R switching of the device can then be synchronized according to the controlling signal of 
choice—either the source input signal or the projector’s internally generated signal—as set in the projector’s 
3D Settings menu.
3.6.3 Active and Passive Stereo 3D...

3-64Mirage WU-L User Manual020-100774-01 Rev. 2 (4-2012)
Section 3: Operation
IR Emitter/3D Passive Filter System: In response to an incoming sync signal, the emitter emits L/R infrared 
signals to a receiver in active 3D shutter glasses, causing the L/R shutters to alternately open and close for 
active stereo 3D applications. Likewise, a 3D passive filter system placed in front of the lens responds to an 
incoming sync signal and alternately polarizes the L/R frames viewed with passive glasses for...

Section 3: Operation
Mirage WU-L User Manual3-65020-100774-01 Rev. 2 (4-2012)
3D Mode: Select the mode of your 3D operation.
•Off: 3D operation is disabled.
•Native: All content is shown at a native frame rate of 96 - 120 Hz input and output.
•Frame Doubled 3D: 3D Content from a single 48-60Hz signal (24/30Hz per eye) are displayed twice to 
provide a 3D content to be viewed at 96-120Hz.
•Dual Input 3D: Content from two independent 48-60Hz ‘passive’ frame locked sources are interleaved into 
a native...

3-66Mirage WU-L User Manual020-100774-01 Rev. 2 (4-2012)
Section 3: Operation
Frame Locking: Enable or disable Frame Lock. When set to Frame Lock, if possible 
output image frames are locked to the input. When Locked, the output is always locked 
to the primary input and never the secondary image, when using Dual input 3D. Free Run 
sets the output to close to 60Hz for all sources. This control must be set to locked if a 3D-Stereo signal is used.
Set Frame Delay: Delays the output signal timing relative...

Section 3: Operation
Mirage WU-L User Manual3-67020-100774-01 Rev. 2 (4-2012)
9. If your emitter has a reverse setting ensure it is set to the Off position.
10. Set all projectors to 3D Sync Input A (or B) depending on your selection in steps 6 & 7.
11. Apply the 3D test pattern to all projectors.
12. Put on your 3D glasses.
13. When 3D is setup correctly, a small set of L’s are visible by closing your right eye and a small set of Rs are 
visible when closing your left eye. 
14. If necessary, adjust the...

3-68Mirage WU-L User Manual020-100774-01 Rev. 2 (4-2012)
Section 3: Operation
Figure 26  Example of 3D Multiple Display Setup
Setup 1
Stereo 
Sync
D/A
Setup 2
Setup 3
Source 
Signal
PCPC
Stereo 
Sync
Source 
Signal
Source 
SignalEmitter
Distribution Amp
EmitterEmitter
Setup 1Stereo Sync is split using a distribution amplifier
Each projector sees the same Stereo Sync
Any projector can send Output Sync to the EmitterSetup 2Stereo Sync from the source is only sent to the 
first projector in the system
Each...

Mirage WU-L User Manual4-1020-100774-01 Rev. 2 (4-2012)
4 Menu Tree 

Contents
Mirage WU-L User Manual4-3020-100774-01 Rev. 2 (4-2012)4.1 MENU TREE
Main Menu
1. Size & Position
2. Image Settings
3, Channel Setup
4. Configuration
5. Reserved
6. Status
7. Secondary Input & 
Switching
8. Language
9. Test PatternSize & Position
1. Resize Presets
2. Size
3. Vertical Stretch
4. Pixel Track
5. Pixel Phase
6. H-Position
7. V-Position
8. Keep Aspect on Auto Setup
9. BlankingBlanking       
Active Input Window
1. Top Blank
2. Bottom Blank
3. Left Blank
4. Right Blank
Channel Setup...

Contents4-4Mirage WU-L User Manual
020-100774-01 Rev. 2 (4-2012)
4.1.1 MENU TREE CONTINUED - CONFIGURATION
Main Menu
1. Size and Position
2. Image Settings
3, Channel Setup
4. Configuration
5. Reserved
6. Status
7. Secondary Input & 
Switching
8. Language
9. Test PatternConfiguration
1. Language
2. Output Options
3. Reserved
4. Power Management
5. Date & Time
6. Menu Preferences
7. Communications
8. Geometry & Color
9. Diagnostics & Calibration
10. Service
11. Option Card Settings
12. Reserved
13....