Christie Projector Mirage WU-L User Manual

Section 3: Operation
Mirage WU-L User Manual3-53020-100774-01 Rev. 2 (4-2012)
Array Status Filter 
Use this option to specify which projectors are included in the ArrayLOC Status report.
•Group, Min Capability includes projectors in the array that meet targets.
•Group includes all projectors in the ArrayLOC group.
•None includes all the projectors detected in the ArrayLOC network.
ArrayLOC Configuration
• ArrayLOC Network
Select the projector-to-projector communication 
network configuration for all...

3-54Mirage WU-L User Manual020-100774-01 Rev. 2 (4-2012)
Section 3: Operation
•PHM Network: All Ethernet messages related to ArrayLOC flow through the PHM Network port of the 
PHM.
 Figure 3-21  Projectors in a PHM Network
Synchronize Keys, Test Pattern, Color Enable
Use the Synchronized option to set the projector to listen for remote keystrokes through the ArrayLOC 
network and the master projector. All synchronized projectors respond to the same keystrokes. Double key 
strokes may not register...

Section 3: Operation
Mirage WU-L User Manual3-55020-100774-01 Rev. 2 (4-2012)
Minimum Array Frame Delay
Indicates the largest minimum frame delay reported for the ArrayLOC group. The value is the largest of 
the reported minimum frame delay required to render the display without tearing artifacts on each 
projector in the ArrayLOC group.
Synchronize RGB Brightness
Use the Synchronized option to synch the RGB brightness for all the synched projectors in the ArrayLOC 
group.
Change this setting for each...

3-56Mirage WU-L User Manual020-100774-01 Rev. 2 (4-2012)
Section 3: Operation
Adjust Projected White and Primary Colors for the Array
User-defined target color spaces allow color primaries and white points to be adjusted independently. For 
example, you can select the target color space User 1, copy the values from the target color space Factory, 
leave the color primaries, and adjust only the white point. All the settings for a user-defined color space are 
editable.
1. Navigate to Main Menu >...

Section 3: Operation
Mirage WU-L User Manual3-57020-100774-01 Rev. 2 (4-2012)
Fine-tune Whites, White Brightness, or Primary 
Colors
 
Projector Color Adjustment lets you fine-tune color 
or brightness for individual projectors that don’t quite 
match the array. For more information, see  Projector 
Color Adjustment, on page 3-41.
These steps outline color adjustments using projector 
color settings until the colors appear to match the rest of 
the projectors in the array. Color adjustments are...

3-58Mirage WU-L User Manual020-100774-01 Rev. 2 (4-2012)
Section 3: Operation
7. To adjust color primary settings (repeat for each projector that needs adjusting):
a. Press P
ROJ,  on the remote. The remote directs commands to the specified projector.
b. Adjust the XXX Part of YYY controls where and YYY is the color being adjusted, and XXX and 
YYY are not the same color (ie. non-dominant colors). Negative values for the non-dominant colors 
are permitted. Adjusting XXX Part of XXX adjusts the color’s...

Section 3: Operation
Mirage WU-L User Manual3-59020-100774-01 Rev. 2 (4-2012)
3.4.6 Main Menu > Status
Access the read-only Status window from the Main menu. It lists a variety of details about the standard and 
optional components detected in the projector. See the Sta tus  menu for versions of hardware and software 
installed, the hours logged in total and for a specific period (such as a rental period), and for your projector 
model name and serial number. In addition, the Sta tus menu identifies the...

3-60Mirage WU-L User Manual020-100774-01 Rev. 2 (4-2012)
Section 3: Operation
Secondary Video Options
The controls adjust the secondary image in the same fashion as the main image controls, see Video Options 
Menu on page 3-20. 
Secondary Input Levels
The controls adjust the secondary image in the same fashion as the main image controls, see Input Levels 
Menu on page 3-22. 
Secondary Advanced Image Settings
The controls adjust the secondary image in the same fashion as the main image controls, see...

Section 3: Operation
Mirage WU-L User Manual3-61020-100774-01 Rev. 2 (4-2012)
3.5 How Color Settings Interact in a Mirage WU-L Array
Image Settings > Color Space tells the projector how to interpret video data coming in. See Color Space on 
page 3-20. 
Image Settings > Advanced Image Settings > Color Settings adjusts the color temperature. Use ArrayLOC 
color and color temperature settings instead. When enabled, ArrayLOC overrides the settings on the Color 
Settings menu. See Color Settings on page...

3-62Mirage WU-L User Manual020-100774-01 Rev. 2 (4-2012)
Section 3: Operation
• A source, usually a computer with a stereo 3D graphics card capable of displaying progressive scan 
(alternating frames) of OpenGL quad buffered stereo 3D applications. Suggested video cards include ATI or 
NVIDIA. 
• Emitter for controlling active shutter glasses.
• An appropriate qualified device that mounts in front of the lens of the projector that will process the light 
from the lens into a passive polarized light....