Christie Projector Mirage WU-L User Manual

Contents
Mirage WU-L User Manual4-5020-100774-01 Rev. 2 (4-2012)4.1.2 MENU TREE CONTINUED - GEOMETRY AND COLOR
Main Menu
1. Size and Position
2. Image Settings
3, Channel Setup
4. Configuration
5. Reserved
6. Status
7. Secondary Input & 
Switching
8. Language
9. Test Pattern
Array Color Target
1. Target Color Space
Array Capability
2. Target Red x
3. Target Red y
4. Target Green x
5. Target Green y
6 Target Blue x
7. Target Blue y
8. Target White x
9. Target White y
10. Copy Color Space From
11. Select...

Contents4-6Mirage WU-L User Manual
020-100774-01 Rev. 2 (4-2012)
4.1.3 MENU TREE CONTINUED - ARRAYLOC
Main Menu
1. Size and Position
2. Image Settings
3, Channel Setup
4. Configuration
5. Reserved
6. Status
7. Secondary Input & 
Switching
8. Language
9. Test Pattern
See Page 4-4 for:
1. Language
2. Output Options
4. Power Management
5. Date & Time
6. Menu Preferences
7. Communications
8. Geometry & Color
9. Diagnostics & Calibration
10. Service
11. Option Card Settings
Configuration
1. Language
2. Output...

Mirage WU-L User Manual5-1020-100774-01 Rev. 2 (4-2012)
5Maintenance
5.1 Safety Warnings and Guidelines
Installers, service trained operators and all users must maintain a safe operating environment at all times. Read 
this section in its entirety and understand all warnings and precautions before operating the projector. 
5.2 Maintaining Proper Cooling
Air vents are located around the projector to keep it at a consistent operating temperature. Make sure that the 
empty space around these vents (“stay...

5-2Mirage WU-L User Manual020-100774-01 Rev. 2 (4-2012)
Section 5: Maintenance
5.3.2 LABELS AND MARKINGS
Observe and follow all warnings and instructions marked on the projector.
The exclamation point within the equilateral triangle tells the user of 
important operating and maintenance (servicing) instructions in the 
literature accompanying the projector.
The lightning flash and arrowhead symbol within the equilateral triangle 
tells the user of “dangerous voltage” not insulated within the projector’s...

Section 5: Maintenance
Mirage WU-L User Manual5-3020-100774-01 Rev. 2 (4-2012)
If any of the following conditions exist, immediately disconnect the projector from the power outlet and 
consult a Christie accredited service technician.
• The power cord is damaged.
• The internal cooling fans do not turn ON when the projector is first powered up. 
• Liquid is spilled into the projector.
• The projector is exposed to excessive moisture.
• The projector is not operating normally or performance has...

5-4Mirage WU-L User Manual020-100774-01 Rev. 2 (4-2012)
Section 5: Maintenance
5.4 Light Module Replacement
 Do not service the projector while it is still connected. There are exposed 
voltages that could cause severe physical injuries and possibly death. 
Always disconnect the projector and wait 2 minutes to allow the power 
supply capacitors to electrically discharge before removing the projector 
covers. 
 Power should always be disconnected from the illumination module before 
servicing, to avoid...

Mirage WU-L User Manual6-1020-100774-01 Rev. 2 (4-2012)
6 Troubleshooting
If the projector is not operating properly, record the symptoms and use this section as a guide. If a solution to 
the problem cannot be found, contact your dealer for assistance. 
NOTE: A Christie accredited service 
technician is required when opening an enclosure to diagnose any “probable cause”.
6.1 Troubleshooting Guidelines
Read, understand and observe all warnings and precautions when diagnosing and servicing the projector....

6-2Mirage WU-L User Manual020-100774-01 Rev. 2 (4-2012)
Section 6: Troubleshooting
System Errors
Shows that a serious malfunction exists and must be reported to the manufacturer as soon as possible. The 
projector will no longer operate. Reset the projector by powering it off and on again, cooling when necessary. 
6.2.1 LED Status Display On the Projector
Projector status is indicated by a single three-color LED adjacent to a 2-digit status display. Refer to Table 6.1 
for a description of LED variations...

Section 6: Troubleshooting
Mirage WU-L User Manual6-3020-100774-01 Rev. 2 (4-2012)
6.2.2 Error Codes
If the status display window shows one of the codes in the Error Codes table you may need a Christie 
accredited service technician to repair the component identified by the error code.
Error codes are displayed in a three phase format: 
• First 2 digits represent the component or error category
• Second 2 digits represent the specific problem
• Display off
This cycle repeats. The LED will be red while...

6-4Mirage WU-L User Manual020-100774-01 Rev. 2 (4-2012)
Section 6: Troubleshooting
6.3 Power
6.3.1 Projector Does Not Power ON
1. Ensure that the projector is plugged in.
2. Ensure that cables are connected and not damaged.
Projector Head Module (PHM) Sensors
SP01 PHM FD sensor 1 overtemp (not connected)
02 PHM FD Air inlet overtemp or sensor not functioning
03 PHM QDPC board overtemp or sensor not functioning
04 PHM FD DMD overtemp or sensor not functioning
05 PHM QDPC board overtemp or sensor not...