Christie Projector Mirage 4K35 User Manual

   Adjust the Image
Mirage 4K35 User Manual51
020-101377-03 Rev. 1 (07-2015)
2. Loosen the lens mount stabilization screw (D).
3. Loosen the vertical lock screw (A).
4. Extend the lens focus (B) completely.
5. Adjust the  Focus knob to retract the lens. Watch the imag e at the top edge of the screen until 
it comes into focus. If the entire screen is in focus, proceed to step 8.
6. Continue retracting the lens.
a. If the bottom edge of the image comes into fo cus before the lens is completely retracted,...

   Adjust the Image
Mirage 4K35 User Manual52
020-101377-03 Rev. 1 (07-2015)
Lock the lens offsets
The lens locking feature reduces image vibration.  For most applications lens locking is not 
necessary.
1. Use the touch panel controller (TPC) or manually adjust the lens offsets to the required position.
2. Unpack and install the three lens offset locking screws.
3. Tighten each locking screw until each screw contacts the lens offset collar.
4. With equal pressure, tighten each locking screw against the...

   Adjust the Image
Mirage 4K35 User Manual53
020-101377-03 Rev. 1 (07-2015)
5. Disconnect the lens motor communication cable.
Adjust DMD convergence
A convergence problem occurs when one or more  projected colors (red, green, blue) appears 
misaligned when examined with a convergence te st pattern. Normally, the three colors should 
overlap precisely to form pure white lines throug hout the image and one or more poorly converged 
individual colors may appear adjacent to some or all of the lines....

   Adjust the Image
Mirage 4K35 User Manual54
020-101377-03 Rev. 1 (07-2015)
Adjusting color by precise chromaticity values
1. On the touch panel controller, tap  Menu > Configuration  > Color Correction  > Select 
Color Adjustment .
2. From the list, select Custom .
3. Tap  Color Adjustments by X,Y .
4. Adjust the precise hues of each primary color component.
Adjust color by saturation
1. On the touch panel controller, tap  Menu > Configuration  > Color Correction  > Select 
Color Adjustment .
2. From...

   Adjust the Image
Mirage 4K35 User Manual55
020-101377-03 Rev. 1 (07-2015)
• Adjust the screw on the lamp side to move the image left or right.
    
image
image
3mm
hex
driver
Base of projector
FRONT 

Mirage 4K35 User Manual56
020-101377-03 Rev. 1 (07-2015)
Operation
This section provides information and procedures for operating the projector.
Projector LED status indicators
The table identifies the LED state colors and meaning.
Turn the projector on
1. Set the all the breaker switches on the lamp power supply to their on positions.
2. Set the breaker switch on the projector baseplate to the on position.
3. When the projector reaches standby, on the touch panel controller, tap  Home > Power .
For more...

   Operation
Mirage 4K35 User Manual57
020-101377-03 Rev. 1 (07-2015)
LED expected behavior on power up
The following table shows the expected behavior  of the projector LED and the MCPU board power 
LED on power up:
At approximately one minute and 15 seconds, the TP C indicates that it is connected and shows the 
home page.
Turn the projector off
1. On the touch panel controller, tap the  Home tab.
2. Tap  Power.
Work with lamps
This section provides information and procedures  for optimizing lamp...

   Operation
Mirage 4K35 User Manual58
020-101377-03 Rev. 1 (07-2015)
3. Tap  OK.
Adjust the lamp position with LampLOC
Use LampLOC™ to configure the lamp position and geom etry when installing a new lamp in the 
projector or at any other time when the lamp performance needs to be optimized. Before adjusting 
LampLOC, make sure the following criteria is met:
• Make sure the lamp is on and the douser (shutter) is open during adjustment. 
Christie recommends a 10-minute warm-up.
• Perform the LampLOC
™...

   Operation
Mirage 4K35 User Manual59
020-101377-03 Rev. 1 (07-2015)
7. For a finer adjustment, repeat steps 5 and 6 but  take the readings at the center of the screen 
instead of at the lens.
View lamp information
To view a history of all previously installed lamps, on the touch panel controller, tap  Menu > Lamp 
>  Lamp History .
Track lamp intensity with LiteLoc
Use the LiteLoc feature to maintain a constant level of brightness over the lifetime of the lamp.
1. On the touch panel controller, tap...

   Operation
Mirage 4K35 User Manual60
020-101377-03 Rev. 1 (07-2015)
4. Tap  Continue .
Add lamp end-of-life indicator
Specify the number of hours remaining before i ssuing an end-of-life indicator for the lamp.
1. On the touch panel controller, tap  Menu > Lamp  > Lamp life warning at (hours).
2. To specify the number of hours remaining before  issuing an end-of-life indicator, enter a value 
or use the plus and minus buttons to increase or decrease the value.
A value of zero disables the feature.
3....