Christie Projector Mirage 4K35 User Manual

   Installation and Setup
Mirage 4K35 User Manual31
020-101377-03 Rev. 1 (07-2015)
5. Slide the selector switch to the  400V location.
6. Re-attach the front panel.
Adjust the projector tilt and level
Adjust the projector tilt to fill the maximum am ount of screen while minimizing keystone. Lens 
offset can be used to center the image in the center of the screen..
1. Secure a safety lifting strap ra ted to handle the projector weight at the rear of the projector.
2. Hoist up the projector.
3. To adjust...

   Installation and Setup
Mirage 4K35 User Manual32
020-101377-03 Rev. 1 (07-2015)
4. Once the required adjustment  is made, tighten the lock nut 
against the bottom of the projector (B).
The projector provides 4 inches   of adjustment at the front and 
11.5 inches of adjustment at the rear. 
5. If the vertical or horizontal posi tion of the projector requires more 
adjustment than the standard feet allow, two 6-inch extension 
rods can be installed to increase the amount of available 
adjustment....

   Installation and Setup
Mirage 4K35 User Manual33
020-101377-03 Rev. 1 (07-2015)
4. Adjust the TPC angle for optimal viewing, then  tighten the mounting arm lock securely so that 
the TPC is held in place at the required location.
 
Connect external exhaust ducting
Connect the existing outside-venting duct to the 8-inch 
diameter exhaust port on the top of the projector. Make sure 
there are no obstructions or bends in the ducting or air 
intakes and the vane switch at the exit duct moves freely.
The...

   Installation and Setup
Mirage 4K35 User Manual34
020-101377-03 Rev. 1 (07-2015)
Add an extractor or a booster if there is insuffic ient airflow. Do not mount the extractor on the 
projector as this may introduce some vibration into the image.
Remove the projector shroud
The lens side shroud must be removed to gain access to the lens. The other shroud must be 
removed when connecting the AC power cord into the front face of the projector.
1. Use finger pressure to push down on the sh roud clips located...

   Installation and Setup
Mirage 4K35 User Manual35
020-101377-03 Rev. 1 (07-2015)
Set up the lens
1. Remove the projector shroud. 
2. Make sure the lens locking lever is in the up position.
3. If attached, remove the rear lens cap from the lens.
4. Slide the lens into the lens mount, aligning all connections. 
5. Secure the lens with the lens locking lever (down position).
6. Calibrate the lens motors. 
For more details, see  Work with lenses on page 60, Remove the projector shroud  on page 34, and...

   Installation and Setup
Mirage 4K35 User Manual36
020-101377-03 Rev. 1 (07-2015)
The mounting frame must be designed to acco mmodate the weight and mounting provisions of 
the projector.
3. Remove the projector feet.
4. Attach the projector to the mounting frame using the four M12 holes (normally used for  projector feet) on the bottom side of the projector. 
Mounting bolts must be grade 8.8 or higher and torqued to 60 ft-lbs.
5. Perform a lamp alignment.
3D setup for Mirage projectors
The Mirage...

   Installation and Setup
Mirage 4K35 User Manual37
020-101377-03 Rev. 1 (07-2015)
• Emitter for controlling active shutter glasses
or 
A qualified device that mounts in front of the lens  of the projector to process the light from the 
lens into a passive polarized light. Contact your Immersive dealer for more information.
Software and content requirements
Note the following software and content requirements for stereo 3D applications:
• Any 3D computer software that supports 3D stereo on a supported...

   Installation and Setup
Mirage 4K35 User Manual38
020-101377-03 Rev. 1 (07-2015)
Passive stereo 3D configuration
The following diagram shows the typical hardware  configuration for passive stereo 3D systems:
3D system timing
Consult the documentation for your glasses or polari zation filter and keep their specifications in 
mind when configuring the projec tor for 3D operation. The projected video must be optimized for 
the glasses’ shutter speed or polarization filter  performance to prevent obvious...

   Installation and Setup
Mirage 4K35 User Manual39
020-101377-03 Rev. 1 (07-2015)
3D input video configurations
The stereo 3D input video stream may be supplied  from the video server to the projector in two 
configurations: Direct-Input 3D or Dual-Input 3D.
Set up a single Mirage 4K to display 3D content
The projector must be installed co rrectly to display 2D content (lamp installed, optically aligned, 
focused, and so on) before completing the following steps to display the 3D content:
1. Confirm the...

   Installation and Setup
Mirage 4K35 User Manual40
020-101377-03 Rev. 1 (07-2015)
2. To select the correct EDID timing, tap  Main > Configuration  > EDID Timing Select  and 
select the required EDID timing.
3. Connect all the required cables betw een the 3D source and the projector.
4. Configure your 3D source.