Christie Projector Mirage 4K35 User Manual

Mirage 4K35 User Manual41
020-101377-03 Rev. 1 (07-2015)
Connect Devices
This section provides information and procedures  for connecting external devices to the projector.
Communication and input ports are located on the projector side input panel, accessed by removing 
the input panel cover. When connecting devices, you can route cables through the opening in the 
frame to the side input panel or directly to the video option cards and MCPU. The image below 
shows the video option card slot numbers and...

   Connect Devices
Mirage 4K35 User Manual42
020-101377-03 Rev. 1 (07-2015)
Four-Port: DDIC card
The following table shows the video quadrant mappings for the DDIC Four-Port input configuration:
Two-Port: TDPIC card
The following table shows the video quadrant mappings for the TDPIC Two-Port input configuration:
Two-Port: DDIC card
The following table shows the video quadrant mapp ings for the DDIC Two-Port input configuration:
Slot 21-In Top right3
Slot 2 2-In Bottom right4
Four-Port 
input...

   Connect Devices
Mirage 4K35 User Manual43
020-101377-03 Rev. 1 (07-2015)
Connect a video source using DisplayPort
The Twin DisplayPort input card (TDPIC) accepts di gital video data from the DisplayPort sources. 
The input configurations listed below are supported.
For information on the video quadrant mapping for Four-Port and Two-Port configurations, see  Two-
Port: TDPIC card  on page 42 and for limitations of one card use for One-Port Dual-Input 3D, see 
Mirage signal connectivity  on page 88....

   Connect Devices
Mirage 4K35 User Manual44
020-101377-03 Rev. 1 (07-2015)
For information on the video quadrant mapping for Four-Port and Two-Port configurations, see  Two-
Port: TDPIC card  on page 42 and for limitations of one card use for One-Port Dual-Input 3D, see 
Mirage signal connectivity  on page 88.
Connect a video source using HDMI
The Twin HDMI input card (THIC) accepts digi tal video data from HDMI sources. The input 
configurations listed below are supported.
Input...

   Connect Devices
Mirage 4K35 User Manual45
020-101377-03 Rev. 1 (07-2015)
For information on the video quadrant mapping for Four-Port and Two-Port configurations, see  Two-
Port: TDPIC card  on page 42 and for limitations of one card use for One-Port Dual-Input 3D, see 
Mirage signal connectivity  on page 88.
Connect a video source using DVI
The Dual Link DVI input card (DDIC) accepts digi tal video data from DVI sources. It does not 
support incoming analog signals. The inpu t configurations listed...

   Connect Devices
Mirage 4K35 User Manual46
020-101377-03 Rev. 1 (07-2015)
1. On the TPC, select  Input > Channel.
2. Scroll the list of channels until you find the channel that best matches your configuration.
3. Tap the channel. An image appears on the screen. If an image does  not appear on the screen, repeat steps 1 to 
3, selecting a different channel.
Connect devices to the 3D Sync ports
The 3D Sync Input and Output ports located on  the MCPU faceplate provide a convenient method 
for interfacing...

   Connect Devices
Mirage 4K35 User Manual47
020-101377-03 Rev. 1 (07-2015)
Set up Ethernet
Ethernet is setup to obtain an IP address automa tically if a DHCP server is on the network. To 
modify IP settings, or manually enter an address.
1. On the touch panel controller, tap  Menu > Configuration  > Ethernet Settings  > Modify 
IP Settings .
2. Set the network information for the projector: • To obtain information automatically from the network, tap  Automatic.
• To manually enter the network...

Mirage 4K35 User Manual48
020-101377-03 Rev. 1 (07-2015)
Adjust the Image
This section provides information and proc edures for adjusting the projector image.
Select screen image orientation
The projector supports front projection, rear pr ojection, front projection inverted, and rear 
projection inverted.
1. On the touch panel controller, tap  Menu > Configuration  > Screen Image Orientation .
2. Select the required orientation from the list.
Maximize light output
To ensure optimal operation, use...

   Adjust the Image
Mirage 4K35 User Manual49
020-101377-03 Rev. 1 (07-2015)
Adjust offset
Always adjust offset before adjusting boresight.
1. Project an image with the primary lens. 2. Select a framing test pattern.
3. Adjust the vertical (A) and horizontal (B) offsets to display a square image on the screen, with  minimal projector aiming error.
 
Adjust horizontal boresight
The purpose of boresight adjustment is to balance the tile of the lens mount to compensate for 
screen-to-projector tilt.
i
For...

   Adjust the Image
Mirage 4K35 User Manual50
020-101377-03 Rev. 1 (07-2015)
1. Loosen the lens mount stabilization screw (D).
2. Loosen the horizontal lock screw (A).
3. Extend the lens focus (B) completely.
4. Adjust the  Focus using the focus knob to retract the lens. Watch the image at the left edge of 
the screen until it comes into focus. If the entire screen is in focus, proceed to step 7.
5. Continue retracting the lens.
a. If the right side of the image comes into fo cus before the lens is...