Christie Projector Mirage 4K35 User Manual

Mirage 4K35 User Manual21
020-101377-03 Rev. 1 (07-2015)
Installation and Setup
Learn how to install, connect, and optimize the projector display.
Site requirements
To safely install and operate the projector, the inst allation location must have restricted access for 
authorized personnel only and meet these minimum requirements.
Physical operating environment
Provides specifications for the operating environment.
• Maximum ambient temperature (operating) 35°C (95°F)
• Minimum ambient temperature...

   Installation and Setup
Mirage 4K35 User Manual22
020-101377-03 Rev. 1 (07-2015)
Tools required for installation
• 12” screwdrivers: Phillips #2 (magnetic) and flat
• 19 mm and 7/8” wrenches
• Assorted Allen keys (metric)
• Christie approved protective safety clothing if working with the lamp
• Lens cleaning tissue and solution
Projector components
IDItemDescription
A Touch panel controller (TPC) A touch-sensitive scre en used to control and monitor operation. For 
information about TPC controls and...

   Installation and Setup
Mirage 4K35 User Manual23
020-101377-03 Rev. 1 (07-2015)
Lamp power supply components
E Exhaust duct and vane switch Extracts heated air fro m the lamp compartment. The vane switch mounted 
inside the rigid port  monitors airflow. See Site requirements  on page 21.
F Liquid cooling air filter cover 
and air filter Filters air before it circulates to co
ol the heat exchanger. For replacement 
instructions, see Replace the laminar airflow device filter  on page 75.
G Shroud...

   Installation and Setup
Mirage 4K35 User Manual24
020-101377-03 Rev. 1 (07-2015)
Position the projector
1. Position the projector at an appropriate th row distance (projector-to-screen distance) and 
vertical position. Ideally, center the projector  with the screen. If space is limited, aim the 
projector slightly off-center. This increases side keystoning, but reduces the horizontal lens 
offset required.
Keep the projector lens as perpendicular to the  screen as possible, even if significantly above...

   Installation and Setup
Mirage 4K35 User Manual25
020-101377-03 Rev. 1 (07-2015)
Install the lamp power supply in a rack stand
1. Remove the right (operators side) panel of the rack stand.
2. Remove the cross bar.
3. Insert the lamp power supply  (LPS) support into the rack stand and align the pins with the 
holes.
4. Lift the LPS into the frame.
5. Remove the bottom 10 panels from the back of the rack stand.
6. Assemble the three-piece airflow duct (supplie d with LPS). First snap the two L shaped...

   Installation and Setup
Mirage 4K35 User Manual26
020-101377-03 Rev. 1 (07-2015)
10. When installing other components in the rack st and allow at least two inches of clearance above 
the LPS handles for ease of servicing.
11. Wire all components within the rack stand and replace the side panel.
Connect the lamp power supply
Danger!  Failure to comply with the followin g results in death or serious injury.
In a multi-projector installa tion there is a risk of a Fire Hazard if the high current DC cables...

   Installation and Setup
Mirage 4K35 User Manual27
020-101377-03 Rev. 1 (07-2015)
1. Ensure the power is disconnected from the lamp power supply (LPS).
2. Loosen three screws to remove the rear lens-side cover.
3. Connect the LPS communication cables:
a. Connect one end of the RS232 cable to the lower port on the LPS labeled RS232 .
b. Connect one end of the Interlock cable to the upper port on the LPS labeled  Interlock.
c. Connect the projector end of the cable to the port labeled  RS232, located on...

   Installation and Setup
Mirage 4K35 User Manual28
020-101377-03 Rev. 1 (07-2015)
g. Connect the negative (-) black lamp lead to the negative (-) igniter terminal, left 
terminal. Connect the positive (+) red lamp lead to the positive (+) igniter terminal, right 
terminal. 
h. Tighten the strain reliefs.
i. Replace the igniter door.
j. Replace the rear lens-side cover.
5. Ensuring AC power is off at the supply, connect the AC directly to the LPS AC input terminal  block according to your region.
• For...

   Installation and Setup
Mirage 4K35 User Manual29
020-101377-03 Rev. 1 (07-2015)
8. If using a Christie extractor, connect  the line cord to the LPS connector labeled  Extractor 
ONLY .
9. Verify the LPS to projector connections by making  sure that all cables connected to the LPS are 
connected to the same projector. 
10. Set the three LPS breakers to their on positions.
11. Set the projector breaker, located on the basepl ate below the projector AC receptacle, to the on 
position.
Configuring ballast...

   Installation and Setup
Mirage 4K35 User Manual30
020-101377-03 Rev. 1 (07-2015)
4. Tighten the screw to secure the harness in place.
Ensure the wire insulation is not crimped under the screw.
5. Slide the selector switch to the  200V location.
6. Re-attach the front panel.
Configuring ballast settings for 400 VAC operation
1. Unplug the LPS from power.
2. Remove the front panel using a Philips screwdriver.
3. Insert the convenience outlet harness (black) wi re into the second position on the terminal...