Christie Digital Systems Lx400 User Manual

59
NETWORK Menu
NETWORK Menu (continued)
Item Description
INFORMATIONSelecting this item displays the NETWORK -INFORMATION- dialog 
for confirming the network settings.
• The PROJECTOR NAME is displayed.
• Nothing (blank) is shown in the “PROJECTOR NAME” field until 
you setup the item (
57).
• When the voltage level of the battery for the built in clock 
decreases, the set time may become incorrect even though accurate 
date and time are input. Replace the battery suitably
 (64).
• IP ADDRESS, SUBNET...

60
Maintenance 
Maintenance
A lamp has finite product life. Using the lamp for long periods of time could cause 
the pictures darker or the color tone poor. Note that each lamp has a different 
lifetime, and some may burst or burn out soon after you start using them. 
Preparation of a new lamp and early replacement are recommended. To prepare 
a new lamp, contact your dealer and tell the lamp type number.
Lamp
Type number = 003-002118-01 (DT00873)
1.Turn the projector off, and unplug the power cord....

61
Maintenance
Lamp warning
Lamp (continued)
 HIGH VOLTAGE HIGH TEMPERATURE HIGH PRESSURE
►The projector uses a high-pressure mercury glass lamp. The 
lamp can break with a loud bang, or burn out, if jolted or scratched, handled 
while hot, or worn over time. Note that each lamp has a different lifetime, and 
some may burst or burn out soon after you start using them. In addition, when 
the bulb bursts, it is possible for shards of glass to fly into the lamp housing, and 
for gas containing mercury to...

62
Maintenance
Filter cover
Filter cover knobs
Filter unit
 Filter coverFilter frame
Filter (finer meshed)
Filter (larger meshed)
Please check and clean the air filter periodically. When the indicators or a 
message prompts you to clean the air filter, comply with it as soon as possible. 
The air filter has two kinds of filters inside. Replace the filters when they are 
damaged or too soiled. To prepare the new filters, make contact with your dealer 
and tell the following type number.
Type number =...

63
NOTE  • Please reset the filter time only when you have cleaned or replaced 
the air filter, for a suitable indication about the air filter.
• The projector may display the message such as “CHECK THE AIR FLOW” or 
turn off the projector, to prevent the internal heat level rising. 
Maintenance
Air filter (continued)
(1) Press the MENU button to display a menu.
(2)  Point at the “FILTER TIME” using the ▼/▲ button, then press the ► 
button. A dialog will appear.
(3)  Press the ▲ button to select RESET on the...

64
Maintenance
Consumption of the battery makes the clock not to work correctly. When the clock is wrong 
or it has stopped, please replace the battery according to the following procedures.
Internal clock batter y 
1.Turn the projector off, and unplug the power cord. Allow the 
projector to cool sufficiently.
2.After making sure that the projector has cooled adequately, 
slowly turn over the projector, so that the bottom is facing.
3.Turn the battery cover fully in the direction indicated “OPEN” 
using a...

65
Maintenance
Other care
In order to ensure the safe use of your projector, please have it cleaned and 
inspected by your dealer about once every year.
1.Turn the projector off, and unplug the power cord. Allow the projector to cool 
sufficiently.
2.After making sure that the projector is cool adequately, lightly wipe the lens 
with a commercially available lens-cleaning wipe. Do not touch the lens 
directly with your hand. If the lens is flawed, soiled or fogged, it could cause deterioration of display...

66
Troubleshooting
Troubleshooting
Related messages
When the unit's power is on, messages such as those shown below may be 
displayed. When any such message is displayed on the screen, please follow the 
instructions described below. If the same message is displayed after the remedy, 
or if a message other than the following appears, please contact your dealer or 
service company.
Although these messages will be automatically disappeared around several 
minutes, it will be reappeared every time the...

67
Troubleshooting
Regarding the indicator lamps
Lighting and flashing of the POWER indicator, the LAMP indicator, and the TEMP 
indicator have the meanings as described in the table below. Please follow the 
instructions within the table. If the same indication is displayed after the remedy, 
or if an indication other than the following is displayed, please contact your dealer 
or service company.
(Continued on next page)
POWER 
indicatorLAMP 
indicatorTEMP 
indicatorDescription
Lighting
In 
Orange...

68
Troubleshooting
Regarding the indicator lamps (continued)
• When the interior portion has become overheated, for safety 
purposes, the power source is automatically turned off, and the indicator lamps 
may also be turned off. In such a case, press the “” (OFF) side of the power 
switch, and wait at least 45 minutes. After the projector has sufficiently cooled 
down, please make confirmation of the attachment state of the lamp and lamp 
cover, and then turn the power on again. NOTE
POWER 
indicatorLAMP...