Christie Digital Systems Lx400 User Manual

9
Setting up
Adjusting the projector's elevator
When the place to put the projector is slightly uneven to the left or right, use the 
elevator feet to place the projector horizontally.
Using the feet can also tilt the projector in order to project at 
a suitable angle to the screen, elevating the front side of the 
projector within 8 degrees.
This projector has 2 elevator feet and 2 elevator knobs. An elevator foot is 
adjustable while pulling up the elevator knob on the same side as it.
1.Holding...

10
Setting up
Connecting your devices
Be sure to read the manuals for devices before connecting them to the projector. 
Make sure that all the devices are suitable to be connected with this product, and 
prepare the cables required to connect.
Please refer to the following illustrations to connect them.
►Do not disassemble or modify the projector.
►Be careful not to damage the cables, and do not use damaged cables.WARNING
►Turn off all devices and unplug their power cords prior to 
connecting them to...

11
Setting up
Connecting your devices (continued)
• Be sure to read the manuals for devices before connecting them to the projector, 
and make sure that all the devices are suitable to be connected with this product. Before 
connecting to a PC, check the signal level, the signal timing, and the resolution.
-  Be sure to consult to the administrator of the network. Do not connect LAN port to any 
network that might have the excessive voltage.
- Some signal may need an adapter to input this projector.
-...

12
Setting up
Connecting power supply
1.Connect the connector of the power cord to the AC inlet of the projector.
2.Firmly plug the power cord's plug into the outlet. 
►Please use extra caution when connecting the power cord, as 
incorrect or faulty connections may result in fire and/or electrical shock.
• Only use the power cord that came with the projector. If it is damaged, contact 
your dealer to newly get correct one.
• Only plug the power cord into an outlet whose voltage is matched to the power...

13
Remote control
Remote control
Laser pointer
This remote control has a laser pointer in place of a finger or rod. The laser beam 
works and the LASER INDICATOR lights while the LASER button is pressed.
►The laser pointer of the remote control is used in place of 
a finger or rod. Never look directly into the laser beam outlet or point the laser 
beam at other people. The laser beam can cause vision problems.WARNING
►Use of controls or adjustments or performance of procedures 
other than those specified...

14
Approx.
3 m  30º
30º
30º
30º
Approx.
3 m 
20º
20º
Approx.
3 m 
Remote control
About the remote control signal
The remote control works with the projector’s remote sensors. This projector has 
three remote sensors on the front, on the top, and on the back.
The sensors can be respectively turned active or inactive using the “REMOTE 
RECEIV.” in the SERVICE item of OPTION menu (
46). Each sensor senses the 
signal within the following range when the sensor is active.
The front and top sensors:
60...

15
Remote control
Using as a wired remote control
The accessory remote control works as a wired remote control, 
when the wired control port at the bottom of the remote control 
connects with the REMOTE CONTROL port on the back of the 
projector via an audio cable with 3.5 diameter stereo mini plugs.
When the remote control signal is hard to reach surely to 
the projector in the environment, this function is effective.
• To connect the remote control with the projector, use an audio cable 
with 3.5...

16
1.Make sure that the power cord is firmly and 
correctly connected to the projector and the outlet.
Power on/off
Turning on the power
2.Remove the lens cover, and set the power switch 
to the ON position (marked “ I “).  
The power indicator will light up in steady orange 
(
67). Then wait several seconds because the 
buttons may not function for these several seconds. 
3.Press the STANDBY/ON button on the projector or 
the remote control.
• Turn the power on/off in right order. Please power on the...

17
(*)        RGB 1          RGB 2          HDMI   
          
VIDEO  S-VIDEO  COMPONENT (Y, CB/PB, CR/PR)
Operating
Operating
1.Press the VOLUME button on the remote control. 
A dialog will appear on the screen to aid you in adjusting the volume.
Adjusting the volume
 ESC  MENU  RESET
  
 POSITION  AUTO 
 
 MAGNIFY 
MY BUTTON VOLUME
 ON  1
MUTE
PUSH ENTER
 PAGE UP   PAGE DOWN
  
 POSITION  AUTO 
 
 MAGNIFY 
MY BUTTON VOLUME
 ON  1
     MUTE
 OFF  2
 FREEZE  KEYSTONE  SEARCH
 STANDBY/ON VIDEO  RGB...

18
Operating
1.Press the VIDEO button on the remote control to select an 
input for video signal.  
Each time you press the button, the projector switches its 
video input port as below.  Selecting an input signal (continued)
●  If the VIDEO button is pushed (when switching from RGB to VIDEO signals) 
when TURN ON is selected for the AUTO SEARCH item in the OPTION menu 
the projector will check the COMPONENT (Y, C
B/PB, CR/PR) port first. If no input 
is detected at the port, the projector will check...