Canon Wux450, Wx520 Multimedia Projector Users Manual

							
221
Using the Projector in Direct Mode
Networked Multi-Projection
Operation in Each Mode
(7) IP addressTo connect to projectors in another s ubnet, enter the projector’s IP address 
here and click (8).
(8) Find projectors Find the projector with the IP address entered in (7). Results of projector 
searching are shown in (9).
(9) Projector information Indicates the name, installation location, and IP address of the projector 
selected in the list or found after searching by IP address.
(10) Password Passwords for projectors on which [NMPJ Password] on the projector’s 
settings screen has been configured ( P182) must be entered here before 
projection.
(11) Start Start projection by the selected projector. During projection, this button is 
labeled [Stop projecting] and can be  clicked to stop projection.
(12) Switch primary/secondary monitor A number is shown here only when secondary  monitor connectivity is activated 
on the computer. Clicking the number will switch between the primary and 
secondary monitor.
(13) Blank the projector Pause projection. Click again to resume projection.
(14) Settings Display the settings window. ( P268)
(15) Projection status Indicates the projection status. 
						

							
222
Using the Projector in Meeting Mode
In meeting mode, multiple computers are connected to multiple projectors. This 
mode is intended for group meetings where multiple computers are used. Up to ten 
computers and six projectors can be connected.
Creating a Session
1In the mode selection menu, select [Meeting Mode].
2The session selection menu is displayed. Click [New]. 
						

							
223
Using the Projector in Meeting Mode
Networked Multi-Projection
Operation in Each Mode
3The projector selection menu is displayed. In the list of projectors at left, 
click the projector to connect to.
You can select up to 6 projectors. Selected projectors are listed at right.
4Click [Next].
• If the [NMPJ Password] setting has been c onfigured on the projector’s settings screen 
( P182 ), the password is now requested. Enter the password.
• To clear a selected projector, click   in the upper right of that projector listing.
• For details on the projector selection menu, refer to “Using the Projector Selection  Menu” ( P254). 
						

							
Using the Projector in Meeting Mode
224
5A window for creating the session is displayed. Specify a session name, 
password, nickname, and desktop (primary or secondary monitor for 
projection), and then click [OK].
6The Meeting Mode window is displayed. Select a projector to control from 
the pull-down list.
• If you choose to set a session password, other users must enter that password to join 
the session. To set a password, click [Set] and enter the password.
• Desktop selection is only available with computers that have dual monitor support. 
						

							
225
Using the Projector in Meeting Mode
Networked Multi-Projection
Operation in Each Mode
7In the list at right, select a computer to use with your designated 
projector. Drag the computer to a desired position in the layout area.
You can arrange up to four computers as desired in the layout area.
8Drag the computers for use in projection in the layout area to rearrange 
them, as needed.
During projection, screens of each comput er will be arranged according to their 
position in the layout area. 
						

							
Using the Projector in Meeting Mode
226
9Click [Start projecting].
Images are now projected from the computers in the layout area.
10To end the session, click   or   in the upper right. 
• To stop projection, click [Stop projecting].
• To rearrange the layout during projection, click [Start projecting] again. Note that if you 
simply rearrange the layout, the new layout will not be applied to projection. 
						

							
227
Using the Projector in Meeting Mode
Networked Multi-Projection
Operation in Each Mode
11The following confirmation message is displayed. To end the entire 
session, click [Close]. To leave the session, click [Exit].
Return to the mode selection menu.
[Exit] is not shown unless other computers are connected. 
						

							
Using the Projector in Meeting Mode
228
Joining a Session
1In the mode selection menu, select [Meeting Mode].
2The session selection menu is displayed. Click [Enter] next to the session 
to join.
To join a session in another subnet, click   and enter the projector’s IP address to 
locate the projector. The application will search for sessions in the other subnet. For 
details, refer to “Using the Session Selection Menu” ( P252). 
						

							
229
Using the Projector in Meeting Mode
Networked Multi-Projection
Operation in Each Mode
3A session login window is displayed. Specify the session password, your 
nickname, and desktop (primary or secondary monitor for display), and 
then click [OK].
4The Meeting Mode window is displayed. Next, follow the instructions 
starting with step 6 in “Creating a Session” ( P222).
Desktop selection is only available with computers that have dual monitor support. 
						

							
Using the Projector in Meeting Mode
230
Meeting Mode Window
(1) Help
View application help.
(2) Back to mode selection Return to the mode selection menu.
(3) Compact display View the window at a compact size. ( P270)
(4) Minimize Minimize the window to the taskbar. To view the window again, click the 
taskbar icon.
(5) Exit Return to the mode selection menu.
(6) Projector list View a list of projectors.
(1) (2) (3) (4) (5)
(6) (7)
(9)
(10)
(14) (15) (8)
(16)
(13)
(11)
(12)