Canon Wux450, Wx520 Multimedia Projector Users Manual

							
211
Networked Multi-Projection
Networked Multi-Projection Overview
From Startup to Shutdown
The procedure from application startup to shutdown is as follows. Example 
windows shown here are from Direct mode.
1Select [Start] > [All Programs] > [Canon NMPJ] > [Network Multiple 
Projection].
If startup is not possible and a message is displayed indicating that NMPJSystem.dll 
could not be found, uninstall the application. If restarting is requested, always restart the 
computer. Reinstall the application and try again. (Do not attempt to install the application 
over an existing installation. Be sure to uninstall it first.)
Windows Firewall
The following alert may be displayed the first time you start the application, depending on 
your Windows Firewall settings. 
To enable communication with projectors, sele ct all check boxes and click the [Allow 
access] button.
 (Screen from Windows 7) 
						

							
From Startup to Shutdown
212
2If the computer is equipped with multiple network adapters, a selection 
window is displayed. Click [OK] next to the desired network adapter.
3On the mode selection window, click the desired mode.
(1) Direct Mode When one computer is connected to one projector. ( P220)
(2) Meeting Mode When multiple computers are connected to multiple projectors. Useful when 
showing multiple computer screens during meetings or other events. ( P230)
The same three buttons are shown in the upper right of this window and subsequent 
windows. (Additional buttons are shown on some windows.)
[ ] View application help.
[ ] Minimize the window to the taskbar. To view the window again, click the taskbar 
icon.
[ ] Close the window.
(1)
(3) (2)
(4) 
						

							
213
From Startup to Shutdown
Networked Multi-Projection
Networked Multi-Projection Overview
(3) Classroom ModeWhen multiple computers are connected to multiple projectors. Gives a single 
presenter control over the specific co mputer and projector used for projection. 
( P241 )
(4) Broadcast Mode When a single computer is connected to multiple projectors. Useful when 
multiple projectors are installed at vari ous positions in an auditorium to project 
the same image. ( P248)
4Depending on the mode, you can create, join, or select a projection 
session.
5Click [Start projecting].
Click [Start projecting] on th e window to start projection.
6To stop projection, click [Stop projecting]. 
						

							
From Startup to Shutdown
214
7To return to the mode selection menu, click   or   in the upper right.
8After a confirmation message is displayed, click [Return to menu].
9To exit the application, click   in the upper right of the mode selection 
menu. 
						

							
215
From Startup to Shutdown
Networked Multi-Projection
Networked Multi-Projection Overview
■Projection Sessions
A session consists of all the comput ers and projectors used in projection.
In Meeting and Classroom modes, the first user must create a session for the 
computers and projectors involved. Other users join the session by selecting it from 
a list of sessions. In Broadcast mode, user s can create a session automatically by 
selecting a projector. 
						

							
216 
						

							
217
Table of Contents
Safety Instructions
Before Use
Operation
Projecting an Image
Useful Functions Available 
During a Presentation
Setting Functions from 
Menus
Installation and Maintenance
Installation
Connecting to a Network
Maintenance
Networked Multi-Projection
Networked Multi-Projection 
Overview
Operation in Each Mode
Functions in All Modes
AppendixOther Information
Index
Operation in Each 
Mode 
						

							
218
Using the Projector in Direct Mode
In this mode, one computer is connected to one projector over the network.
Procedure
1In the mode selection menu, select [Direct Mode].
2The Direct Mode window is displayed. Click  .
To connect to projectors in another subnet, enter the projector’s IP address in the [PJ IP 
address] field and click  . 
						

							
219
Using the Projector in Direct Mode
Networked Multi-Projection
Operation in Each Mode
3The projector selection menu is displayed. Click the projector to connect 
to.
4The Direct Mode window is displayed again. Click [Start projecting].The computer screen is now projected.
For details on the projector selection menu, refer to “Using the Projector Selection Menu” 
( P254 ).
• If the [NMPJ Password] setting has been c onfigured on the projector’s settings screen 
( P182 ), the password is now requested. Enter the password.
• To stop projection, click [Stop projecting].
• A BUSY icon ( ) indicates that the projector is not available, whether it is off, in use  by other computers, or unavailable fo r other reasons. The   icon is not updated 
automatically. To view updated projector status, select or search for projectors again. 
						

							
Using the Projector in Direct Mode
220
Direct Mode Window
(1) Help
View application help.
(2) Back to mode selection Return to the mode selection menu.
(3) Compact display View the window at a compact size. ( P270)
(4) Minimize Minimize the window to the taskbar. To view the window again, click the 
taskbar icon.
(5) Exit Return to the mode selection menu.
(6) Projector list View a list of projectors.
(1) (2) (3) (4) (5)
(6) (7)
(8)
(9)
(10)
(12)
(11)
(13) (14) (15)