Canon Wux450, Wx520 Multimedia Projector Users Manual

							
111
Customizing System Operation (System Settings)
Operation
Setting Functions from Menus
Assigning a Channel 
for Remote Control
> [System settings] > [Remote 
control channel]
When using multiple projectors at 
the same time (maximum 4), you can 
assign a different channel to each 
remote control so that each operates 
independently.
Selecting the Projector Channel
Press the  OK button to accept your 
setting and then press the  MENU 
button or  EXIT button.
• The factory default is [Independent] for both 
projector and remote control.
• After changing the channel on the menu, be  sure to change the channel of the remote 
control too.
• If a cable is connected, it is not necessary  to perform remote control channel setting.
To Unlock Key Lock Function
Turn off the projector and unplug the 
power plug. Hold down the  OK button on 
the main unit and plug in the power cord, 
as you continue to hold down the  OK 
button. In a moment, a beep will sound, 
and the controls will be unlocked.
HDMIComponentLAN
Digital PCAnalog PCUSB
Ch1
Ch2
Ch3
Ch4 Select the remote control 
channel to use with this 
projector.
Independent Remote controls set to any 
channel can be used. 
						

							
112
Customizing System Operation (System Settings)
Selecting a Channel on the 
Remote control
You can change the channel on the 
remote control as follows.
Reducing Motion 
Blur
> [System settings] > [Motion blur 
reduction]
Motion blur is blurring that occurs 
during video playback. Motion blur 
reduction can make this blurring 
less noticeable. This function is 
available in [Presentation] or 
[Dynamic] image modes ( P95).
Press the  OK button to accept your 
setting and then press the  MENU 
button or  EXIT button.
• [Off] is the factory default.
• If motion blur reduction generates 
distracting image noise, select [Off].
• Effects of motion blur reduction cannot be  checked during menu display.
• Especially effective for motion of computer  graphics and similar high-resolution 
images.
Ch1
Press and hold the  OK 
button and [ ] button at the 
same time for 3 seconds.
Ch2 Press and hold the  OK 
button and [ ] button at the 
same time for 3 seconds.
Ch3 Press and hold the  OK 
button and [ ] button at the 
same time for 3 seconds.
Ch4 Press and hold the  OK 
button and [ ] button at the 
same time for 3 seconds.
Independent Press and hold the  OK 
button and   button at the 
same time for 3 seconds.
HDMIComponentLAN
Digital PCAnalog PCUSB
Off Motion blur reduction is not 
performed.
On
Motion blur reduction is performed. 
						

							
113
Customizing System Operation (System Settings)
Operation
Setting Functions from Menus
Specifying HDMI Input
> [System settings] > [HDMI In]
Set the type of equipment which is 
connected to the HDMI port.
Press the OK button to accept your 
setting and then press the  MENU 
button or  EXIT button.
• [Auto] is the factory default.
Selecting a Display 
Language
> [System settings] > [Language]
You can select the language in which 
the menus are displayed.
Use the [ ] / [ ] / [ ] / [ ] buttons to 
select the menu language, then press 
the OK button.
HDMIComponentLAN
Digital PCAnalog PCUSB
Auto Select when AV equipment will 
be connected. Image 
processing, menu displays, 
and other elements are 
adjusted for video equipment.
Computer Select when a computer will be 
connected. Image processing, 
menu displays, and other 
elements are adjusted for a 
computer.HDMIComponentLAN
Digital PCAnalog PCUSB
English
German
French
Italian
Spanish
Portuguese
Swedish
Russian
Dutch
Finnish
Norwegian
Tu r k i s h
Polish
Hungarian
Czech
Danish
Arabic
Chinese 
(Simplified)
Chinese 
(Traditional)
Korean
Japanese 
						

							
114
Customizing System Operation (System Settings)
When the setting is completed, press 
the OK button to accept your setting 
and then press the  MENU button or 
EXIT  button.Requiring a Password 
for Operation
> [System settings] > [Other settings] > 
[Password settings ]
Disables the projector unless the 
correct password is entered.
Press the OK button to accept your 
setting and then press the  MENU 
button or  EXIT button.
• [Off] is the factory default.
• You cannot set [On] unless you have 
completed [Register password].
Once you set a password, the 
password entry screen appears at 
power-on.
Enter a 4 digit password.
Enter the password using the [ ] / [ ] / 
[ ] / [ ] buttons.
If the password is valid, the projection 
starts. If you enter a wrong password 
three times, the power will be turned off.
• The power is also turned off if no password 
is input for 3 minutes.
HDMIComponentLAN
Digital PCAnalog PCUSB
Off The projector can be used even if no 
password is entered.
On The projector cannot be used unless 
you enter your password. 
						

							
115
Customizing System Operation (System Settings)
Operation
Setting Functions from Menus
Setting a Password
> [System settings] > [Other settings] >
[Register password]
You can register a password for 
starting projection.
Press the OK button after selecting 
[Register password], and the following 
screen for registering a password 
appears.
Enter a 4 digit password.
Enter the password using the [ ] / [ ] / 
[ ] / [ ] buttons.
The 4-digit password is entered from 
the left to right digits. When the final 
digit is entered, the password is 
automatically registered.
Press the  MENU button to abort the 
registration.
To Cancel the Password
Turn off the projector and unplug the 
power plug.
Hold down the  MENU button on the side 
control and connect the power plug. 
Make sure to keep holding down the 
MENU  button until a beep sounds. When 
the beep sounds, the password is 
canceled. (The entered password is also 
reset.)
To forcibly cancel the password from the 
remote control, in standby state press the 
MENU  button 3 times, then press the 
POWER  button.
HDMIComponentLAN
Digital PCAnalog PCUSB 
						

							
116
Customizing System Operation (System Settings)
Restoring Original 
Gamma Settings
> [System settings] > [Other settings] >
[Gamma restore]
This function is used when changing 
and turning of the tone 
characteristics and achromatic color 
is noticed over a long period of time.
Gamma restore can only be used 
when the lamp has been on for 
approximately 30 minutes or longer.
• If Gamma restore is performed, the 
projected image will be adjusted for a 
period of approximately 150 seconds.
• To stop Gamma restore, press the  POWER 
button or the  EXIT button.
HDMIComponentLAN
Digital PCAnalog PCUSB
Off Returns to the factory default without 
performing Gamma restore.
AdjustPerforms Gamma restore and applies 
the result.
OK Gamma restore is performed.
CancelGamma restore is not 
performed.
If Gamma restore is performed, the 
tone characteristics and achromatic 
color will be restored as close as 
possible to the condition when the 
projector was purchased, however it is 
not possible to restore it completely to 
the original condition. So the changing 
and turning color cannot be eliminated 
completely. 
						

							
117
Customizing System Operation (System Settings)
Operation
Setting Functions from Menus
Resetting the Lamp 
Counter
> [System settings] > [Other settings] >
[Lamp counter]
You can reset the lamp counter that 
indicates the time for lamp 
replacement.
Select [Lamp counter] and press the 
OK button to display the lamp counter.
Select [Reset] and press the  OK button.
Select [Yes] on the screen for 
confirmation and press the  OK button 
to reset the lamp counter.
Press the  MENU button or  EXIT button.
■About the Display of the 
Lamp Counter
The lamp counter displays the hours of 
use of the lamp in the following way.
Less than 2,700 hours
Displayed as a  green bar.
2,700 hours to less than 3,000 hours
Displayed as a  green and yellow  bar.
When the lamp hours are 2,700 hours 
to less than 3,000 hours, the message 
“Obtain a new lamp.” appears when 
power is turned on.
Over 3,000 hours
Displayed as a  green, yellow and red  
bar.
The message “Replace with the new 
lamp.” appears when power is turned 
on.
HDMIComponentLAN
Digital PCAnalog PCUSB
Do not reset the lamp counter 
except when you have replaced 
the lamp. Otherwise, the lamp 
counter cannot indicate the 
correct timing for replacing the 
lamp.
For details of lamp replacement, 
refer to  page 197 . 
						

							
118
Customizing System Operation (System Settings)
Resetting the Air Filter 
Counter
> [System settings] > [Other settings] > 
[Air filter counter]
This resets the counter which 
reminds you of the time for cleaning 
and replacing the air filter.
To view the air filter counter, press the 
OK  button when [Air filter counter] is 
selected.
Select [Reset] and press the  OK button.
To reset the air filter counter, select 
[Yes] on the confirmation screen and 
press the  OK button.
Press the  MENU button or  EXIT button.
Updating the 
Firmware
> [System settings] > [Other settings] > 
[Firmware]
Use a firmware update program 
stored on a USB flash drive to 
update the projector firmware.
Download firmware updates from the 
Canon website and store them at the 
root directory on the USB flash 
drive.
Select [Firmware], press the  OK button, 
and check the firmware version 
displayed. Selecting [OK] will display an 
update confirmation screen. To update 
the firmware, select [Yes].
Firmware updating takes about three 
minutes. During the update, the LED 
indicator will flash in red. Do not turn off 
the projector while the LED is flashing.
After the update, the projector will 
automatically turn itself off and enter 
standby mode.
HDMIComponentLAN
Digital PCAnalog PCUSB
For details about how to replace or 
clean the filter, refer to  page 195.
HDMIComponentLAN
Digital PCAnalog PCUSB
• In some cases, it may not be 
possible to download the update. If 
so, contact the Canon Customer 
Support Center.
• This firmware version is for 
illustration only, and the actual 
number will be different. 
						

							
119
Customizing System Operation (System Settings)
Operation
Setting Functions from Menus
Resetting to the 
Default Setting
> [System settings] > [Other settings] > 
[Factory defaults]
You can reset the menu item settings 
and restore the system settings to 
the factory defaults.
Select [Factory defaults] and press the 
OK  button. The following screen for 
confirmation appears.
• This function does not reset the values for 
[Lamp counter], [Language], [Remote 
control], [Input signal], [Network settings], 
[Air filter counter], [Professional settings] 
([Micro-digital image shift], [Registration], 
[Fan mode], [Vertical projection], and [Edge 
blending]) and [Create profile].
• For factory defaults settings, refer to  P300 - 
P307 .
• The contents of the user memory return to 
the conditions at the time it was saved. 
(P96 )
HDMIComponentLAN
Digital PCAnalog PCUSB
OK Settings are reset to default.
Cancel Settings are not reset to default. 
						

							
120
Checking Projector Information
> [Information]
You can check information about the 
signal types of the images projected 
and other information.
Information shown
* Not displayed when network functions are [Off].
HDMIComponentLAN
Digital PCAnalog PCUSB
ItemExplanation
Model name WUX450 / WX520
Input signal Details of the input signal currently selected 
Information such as the type, resolution, and frequency of 
the signal is displayed.
FirmwareCurrent firmware version
Serial no. Serial number unique to this projector
E-mail sender 
address* Sender e-mail address used for sending error mails 
(
P183 )
E-mail recipient 
address* Displays [Already set] or [Not set] to show whether a 
recipient e-mail address has been set for receiving error 
mails. (
P183)
Projector name* Name which identifies this projector on the network
Location* Location where the projector is installed
System information 
ID System information. Normally this is not displayed.