Canon scanner imageFORMULA ScanFront 300P User Manual

							
3-12
Chapter 3   ScanFront Setup
❏ Display Language Setting
You can select the language displayed on touch panel. If 
you change this setting, restart the scanner.
Hint
The display language setting can also be configured in 
[Language/Timezone] on the Web Menu (Administrator Mode) 
(see p. 6-30) .
❏Network Test
Confirm whether communication is enabled between the 
ScanFront and other devices on the network. Enter the IP 
address of a device and press the [Execute] button to ping 
the specified IP address and confirm whether 
communication with the device is enabled.
❏Switch to Web Application Mode (from 
Standard Mode of ScanFront 330 Only)
Switch to Web Application Mode when using the 
ScanFront 330 in Standard Mode.
If you execute switching to Web Application Mode, 
ScanFront restarts and switches to Web Application Mode.
IMPORTANT
There is no data compatibility between Standard Mode and 
Web Application Mode. Before switching to Web 
Application Mode, back up the data as a safety precaution. 
						

							Chapter 4   ScanFront Service
1. About ScanFront Service ................................. 4-2
2. Installing ScanFront Service ............................ 4-3
System Requirements ...........................................4-3
Installation .............................................................4-3
3. ScanFront Service Setup ................................. 4-6
ScanFront Settings................................................4-6
Changing the Port Number Used for 
Communication .....................................................4-6 
						

							4-2
Chapter 4   ScanFront Service
1.About ScanFront Service
ScanFront Service is software that supplements the network functions of the ScanFront. To use this software, install it on a computer 
connected to the same network as the ScanFront. (The computer on which ScanFront Service is installed will be herein referred to 
as the “ScanFront Service Server”.)
By configuring a ScanFront Service Server, you can send 
scanned images to locations on the network, such as the 
following, where direct transfer from the ScanFront is 
disabled.
●Destinations (folders on computers, printers, etc.) 
located on a different network segment
●Printers on the network
●Shared folders on a computer that is specified by IP 
address
●Certain NAS (network-attached storage)
Scanned images from the ScanFront are sent via the 
ScanFront Service Server to the user specified destination.
Up to 100 ScanFront scanners can be connected to a single 
ScanFront Service Server. However, only up to 15 ScanFront 
scanners can communicate with the ScanFront Service Server 
at any one time. 
						

							4-3
Chapter 4   ScanFront Service
2.Installing ScanFront Service
❏System Requirements
Install ScanFront Service on a computer that is connected 
to the same network as the ScanFront, and that meets the 
following requirements.
Operating System
●Windows XP (32 bit/64 bit)
●Windows Server 2003 (32 bit/64 bit)
●Windows Vista (32 bit/64 bit)
●Windows Server 2008 (32 bit/64 bit)
●Windows Server 2008 R2
●Windows 7 (32 bit/64 bit)
●Windows 8 (32 bit/64 bit)
●Windows Server 2012 (64 bit)
❏Installation
1.Insert the application disc into the computer.
2.Start the ScanFront Service installer.
Use Windows Explorer, for example, to locate the installer 
in the following folder on the disc, and double-click the 
installer to start it.
Q: \ScanFrontService\setup.exe 
(“Q” is the letter assignment for the disc drive)
3.Click [Next].
4.Select “I accept the terms of the license agreement” 
and then click [Next].
A screen for selecting the installation folder appears. 
						

							4-4
Chapter 4   ScanFront Service
5.Click [Next].
A screen for entering account information appears.
6.Enter the account information, and click [Next].
Use an administrator account on the computer on which 
the service will be installed.
 When entering a local account on the computer, include 
“./” at the beginning of the account name.
 If the computer is part of a domain and you are entering 
the domain account here, enter the account in one of the 
following formats.
IMPORTANT
Make sure to specify an administrator account. In addition, be 
aware that ScanFront Service will not function properly with 
accounts for which a password is not configured.
A screen for specifying whether to start the service 
immediately appears.
7.Specify [Execute now] if you want to start the service 
immediately, or [Execute later] if you want to start the 
service after restarting the computer, and then click 
[Next].
An install confirmation screen appears.
Entry Format Example
\area1\SFUser
@[email protected] 
						

							4-5
Chapter 4   ScanFront Service
8.Click [Install].
Installation starts. When installation is complete, a screen 
indicating that installation is complete appears.
9.Click [Close].
Notes on Installing ScanFront Service
 ScanFront Service creates log files during operations. As 
a result, these log files and the install destination folder 
will not be deleted, even after ScanFront Service is 
uninstalled. 
						

							4-6
Chapter 4   ScanFront Service
3.ScanFront Service Setup
❏ScanFront Settings
You must configure the following setting on the ScanFront 
to send scanned images using the ScanFront Service 
Server.
1.Log in to the Web Menu in Administrator Mode (see 
p. 6-5).
2.Click [Server Settings], and then [ScanFront Service 
Server].
3.Enter the host name (address) of the ScanFront 
Service Server.
IMPORTANT
 ScanFront Service uses port number 50000 to communicate 
with the ScanFront. Do not change the port number value from 
50000.
 To use ScanFront Service, you must start the ScanFront 
Service Server before turning ON the ScanFront.
❏Changing the Port Number Used for 
Communication
If port number 50000 is already in use, for example, and 
you want to use a different port number for 
communication with the ScanFront, modify the following 
ini file before specifying the new port number.
Folder: 
C:\Program Files\Canon Electronics Inc\ScanFront 
Service\etc
File name: 
ScanFront.ini
Area to be modified: 
Replace the port number that appears in “port=50000” 
with the port number you want to use.
Settings for Environments with Firewalls
If a firewall is installed on the computer on which 
ScanFront Service is installed and the firewall is enabled, 
ScanFront Service will not run. In such cases, you must 
change the firewall settings and restrictively open the port 
used by ScanFront Service. For details, refer to the 
operating instructions for your firewall. 
						

							Chapter 5   Operating Procedures
1. Flow of Scanner Operations ............................. 5-2
2. Turning the Power ON and OFF ...................... 5-3
Turning the Power ON .......................................... 5-3
Turning the Power OFF ........................................ 5-3
3. Login Screen .................................................... 5-4
Login Screen Types.............................................. 5-4
When Using Server Authentication....................... 5-4
List Type Login ..................................................... 5-5
Key in Type Login ................................................. 5-6
Fingerprint Authentication 
(Only Available with the ScanFront 300P) ............ 5-7
4. Screen Displayed after Login ........................... 5-8
Home Screen........................................................ 5-8
Job Button Screen ................................................ 5-8
5. User Settings Screen ....................................... 5-9
Change Password ................................................ 5-9
Fingerprint Registration ........................................ 5-9
6. Fingerprint Registration 
(Only Available with the ScanFront 300P)...... 5-10
Fingerprint Authentication................................... 5-10
Registering a Fingerprint .................................... 5-11
7. Scanning Procedures ..................................... 5-13
Scanning From the Home Screen ...................... 5-13
Scanning From the Job Button Screen............... 5-14
Address Selection Screen .................................. 5-15
USB Memory Screen .......................................... 5-17
Print Settings Screen .......................................... 5-18
Scanning............................................................. 5-19
8. Registering and Editing Addresses ................ 5-23
Registering a New Address ................................ 5-23
Modifying an Address ......................................... 5-25
Copying an Address ........................................... 5-26
9. Scan/Delivery Options.................................... 5-27
Scan Settings ..................................................... 5-28
File Formats........................................................ 5-32
Security Settings for PDF Files........................... 5-33
Delivery Options ................................................. 5-34 
						

							5-2
Chapter 5   Operating Procedures
1.Flow of Scanner Operations
The procedure and screen transitions for the process from turning the scanner ON, to sending an image file are as follows. For 
descriptions of the various settings, refer to the appropriate reference pages. 
Turn the power ON
 (See p. 5-3.)
No user is registered
* When no user is registered and only 
the Shared Address Book and Shared 
Job Button are used 
Home screen 
(See p. 5-8.)
* Set the screen that appears after login in the user settings.
* When you use server authentication, the user that logged in 
is registered automatically. 
Job Button screen 
(See p. 5-8.)
* Users restricted by [Use only Job 
Buttons] in the function 
restrictions cannot scan from the 
Home screen.
Scanning starts immediately after a 
job button is pressed. 
User Settings screen 
(See p. 5-9.)
* The User Settings screen enables 
setting a password for the user that 
logged in, and registration for the 
ScanFront 300P.
Scan/Delivery Options screen 
(See p. 5-27.)
Scan (The process after scanning differs depending on the Delivery Options) 
(See p. 5-34.)
Scanning finishes (A document confirmation message appears) 
(See p. 5-20.)
The document and 
image are not checkedAfter scanning of the 
document ends, the image is 
sent as is and the process 
ends. 
Send/Image Confirmation screen 
(See p. 5-21.)
Address Confirmation screen 
(See p. 5-22.)
The image is sent 
without the address 
being confirmed.
Send (The screen displayed after sending differs depending on the Delivery Options)
 (See p. 5-34.)
Home screen Job Button screen Login screenLogin screen 
(See p. 5-4.)
Address selection screen 
(See p. 5-15.) Password setting screen 
(See p. 5-9.)
Fingerprint registration screen 
(See p. 5-10.)
* Delivery Options 
settings are also applied 
to job buttons.
Users are registered (device/server authentication) 
						

							5-3
Chapter 5   Operating Procedures
2.Turning the Power ON and OFF
Use the power switch to turn the scanner ON, and press the [Power off] button on the touch panel to turn it OFF.
❏Turning the Power ON
Press the power switch to turn the scanner ON. The power 
indicator lights, and the Home screen or the login screen 
appears.
Hint
 It takes approximately 40 seconds for the Home screen to 
appear after the power switch is turned on. 
 If users have been registered, the login screen appears. (See 
“Login Screen” on p. 5-4.)
 When the power indicator is lit but nothing appears on the 
touch panel, Display Off has activated to turn the panel display 
off. You can touch the panel to restore the display. (See 
“Display Off” on p. 6-31.)
 When the power indicator is flashing but nothing appears on 
the touch panel, the Low Power mode has activated to 
temporarily stop scanner operations. To switch out of Low 
Power mode, press the power switch or touch the touch panel. 
(See “Low Power Mode” on p. 6-31.)
❏Turning the Power OFF
Press the [Power off] button displayed at the bottom left of 
the panel to turn the scanner OFF.
IMPORTANT
 When restarting the scanner, wait at least 5 seconds after 
turning the power OFF before turning it ON again.
 If the scanner stops responding, press and hold the power 
switch to shut down the system, and then press the power 
switch to turn the scanner ON again. In such cases, settings 
configured immediately before shutting down may be lost.
Home screen
Power 
indicator Power switch