Canon scanner imageFORMULA ScanFront 300P User Manual

							3-2
Chapter 3   ScanFront Setup
1.Before Setting Up the Scanner
Before setting up the scanner, you need to move it to the installation site, and connect the AC adaptor and network cable.
❏Installation Location
The performance of this scanner is affected by the 
environment in which it is installed. Make sure that the 
location where the scanner is installed meets the following 
environmental requirements.
●Provide adequate space around the scanner for 
operation, maintenance, and ventilation.
●Avoid installing the machine in direct sunlight. If 
this is unavoidable, use curtains to shade the 
scanner.
●Avoid locations where a considerable amount of 
dust accumulates.
●Avoid warm or humid locations, such as in the 
vicinity of a water faucet, water heater, or 
humidifier, and avoid locations where the fumes 
from ammonia, paint thinner, or other volatile 
chemicals may be present.
●Avoid locations that are subject to vibration.●Avoid exposing the scanner to rapid changes in 
temperature. If the room in which the scanner is 
installed is cold but rapidly heated, water droplets 
(condensation) may form inside the scanner. This 
may result in a noticeable degradation in scanning 
quality.
The following conditions are recommended for 
optimal scanning quality:
Room temperature: 10 °C to 32.5 °C (50 °F to 
90.5 °F)
Humidity: 20% to 80% RH
●Avoid installing the scanner near equipment that 
generates a magnetic field (e.g. speakers, 
televisions, or radios).
At least 
15.75 
(40 cm)
At least 
23.62 (60 cm) 
						

							3-3
Chapter 3   ScanFront Setup
❏Connecting the AC Adapter
Follow the procedure shown below to connect the AC adapter.
CAUTION
Make sure to use only the AC adapter and power cord included with the scanner.
aConnect the power cord and AC adapter.
bInsert the plug of the AC adapter into the power connector.
cConnect the power cord to the wall outlet.
❏Connecting the Network Cable
Insert the network cable connector (RJ-45) into the LAN port.
The shape of the power plug 
varies by country and region. 
						

							3-4
Chapter 3   ScanFront Setup
2.Turning the Power ON and OFF
Use the power switch to turn the scanner ON, and press the [Power off] button on the touch panel to turn it OFF.
❏Turning the Power ON
Press the power switch to turn the scanner ON. The power 
indicator lights, and the Home screen or the login screen 
appears.
IMPORTANT
 It takes approximately 40 seconds for the Home screen to 
appear after the power switch is turned on.
 When the power indicator is lit but nothing appears on the 
touch panel, Display Off has activated to turn the panel display 
off. You can touch the panel to restore the display. (See 
“Display Off” on p. 6-31.)
 When the power indicator is flashing but nothing appears on 
the touch panel, the Low Power mode has activated to 
temporarily stop scanner operations. To switch out of Low 
Power mode, press the power switch or touch the touch panel. 
(See “Low Power Mode” on p. 6-31.)
❏Turning the Power OFF
Press the [Power off] button displayed at the bottom left of 
the panel to turn the scanner OFF.
IMPORTANT
 When restarting the scanner, wait at least 5 seconds after 
turning the power OFF before turning it ON again.
 If the scanner stops responding, press and hold the power 
switch to shut down the system, and then press the power 
switch to turn the scanner ON again. In such cases, settings 
configured immediately before shutting down may be lost.
Home screen
Power 
indicator Power switch 
						

							3-5
Chapter 3   ScanFront Setup
3.Configuring the Scanner Settings
The scanner setup consists of configuring the initial network settings from the [Administrator setting] screen, and then configuring 
the settings needed to use the scanner as described in Chapter 6 “Web Menu (Administrator Mode)”.
❏Administrator Settings
The following items are available for administrator settings. For details, see “Configuring Administrator Settings” on p. 3-8.
Hint
Except for the scanner maintenance items (roller counter reset, touch panel adjustment, and initialization), the administrator setting items 
can be configured from the Web Menu (Administrator Mode). For details, see “Web Menu (Administrator Mode)” on p. 3-6 or Chapter 6 “Web 
Menu (Administrator Mode)”.
Setting ItemDescriptionAdministrator settingWeb Menu 
(Administrator Mode)
Network settingsSet the Device Name and IP Address needed to 
connect to the network.Ye s Ye s
Change administrator 
passwordSet the password required for logging in to 
[Administrator setting] and the Web Menu.Ye sYe s
Backup / Restore all 
settingsBack up or restore the scanner settings. Yes Yes
Login type settingSelect the login screen for users.Ye sYe s
Roller Counter Reset Reset the counter after replacing the feed roller. Yes No
Format ScanFrontUse to delete all of the current settings, such as 
when changing the operating environment of the 
scanner.Ye sNo
Touch panel adjustmentAdjust the touch panel when it does not operate as 
expected.Ye s N o
Display language settingSet the language displayed on the touch panel.Ye sYe s
Network TestConfirm whether communication is enabled 
between the ScanFront and other devices on the 
network.Ye s N o
Change to the web 
application mode 
(ScanFront 330 only)Switch to Web Application Mode when using the 
ScanFront 330 in Standard Mode.Ye sNo 
						

							3-6
Chapter 3   ScanFront Setup
❏Web Menu (Administrator Mode)
The following setting items are available from the Web Menu (Administrator Mode). For details, see Chapter 6 “Web Menu 
(Administrator Mode)”.
Hint
From the Web Menu (User Mode), which is available to all users, the configuration of some functions is restricted.
Setting ItemDescriptionWeb Menu 
(Administrator Mode)Web Menu 
(User Mode)
User AdministrationRegister new users and edit user settings. From 
User Mode, only the editing of user settings is 
available, and some settings cannot be edited.Ye s  (See p. 6-6)Yes, partially. (See 
p. 8-4)
Address Book Settings
Register and edit entries in the Shared Address 
Book. From User Mode, you can register and edit 
entries in the My Address Book.
Ye s  (See p. 6-14)Ye s  (See p. 8-9)
Job Button SettingsRegister and edit the Shared Job Button. From 
User Mode, you can register and edit the My Job 
Button.Ye s  (See p. 6-20)Ye s  (See p. 8-16)
Device ConfigurationConfigure the scanner settings.
Network SettingsConfirm the [Device Name] and [IP Address] 
settings of the scanner.Ye s  (See p. 6-30)No
Language/TimezoneSet the language displayed on the touch panel and 
the geographic region where it will be used.Ye s  (See p. 6-30)No
Device OperationSet the Auto Logout and Low Power Mode 
settings for users.Ye s  (See p. 6-31)No
Login OptionsSelect the login screen for users.Ye s  (See p. 6-31)No
Administrator SettingsRegister the password and e-mail address of the 
administrator.Ye s  (See p. 6-32)No 
						

							3-7
Chapter 3   ScanFront Setup
Setting ItemDescriptionWeb Menu 
(Administrator Mode)Web Menu 
(User Mode)
Server SettingsRegister the mail server, address book server and 
authorization server.
E-mail Server / Fax 
SettingsRegister the SMTP server to be used for sending e-
mail and faxes.Ye s  (See p. 6-34)No
Authentication ServerRegister a domain server that can search users with 
Active Directory.Ye s  (See p. 6-35)No
Address Book ServerRegister an LDAP server that can search e-mail 
address books.Ye s  (See p. 6-36)No
FTP ServerConfigure settings for saving image files to the 
FTP server.Ye s  (See p. 6-37)No
NTP ServerRegister an NTP server to enable automatic 
adjustment of the scanner’s clock.Ye s  (See p. 6-37)No
ScanFront Service 
ServerRegister the computer on the network on which 
ScanFront Service is installed.Ye s  (See p. 6-37)No
CertificatesImport the root certificate of the LDAP server to 
the ScanFront.Ye s  (See p. 6-37)No
System Settings Configure the settings for managing the scanner.
Backup / RestoreBack up or restore the scanner settings.Ye s  (See p. 6-40)No
Module Version 
InformationDisplay the version information, and update the 
version, of the ScanFront module.Ye s  (See p. 6-41)No
Log SettingsRecord usage statistics to a log file.Ye s  (See p. 6-42)No
Screenshot Saves the ScanFront screen display as a BMP file. Yes (See p. 6-43)No 
						

							3-8
Chapter 3   ScanFront Setup
4.Configuring Administrator Settings
Enter the administrator password and log in to configure administrator settings.
❏Logging In to the Administrator Settings
Follow the procedure below to configure the [Device 
name] and [IP address] needed to connect the scanner to a 
network.
1.Press [Administrator setting].
The [Administrator Password] input box appears.
2.Press [OK] to display the [Administrator setting] 
screen.
No administrator password is set by default.
3.Select the setting item to configure. 
						

							3-9
Chapter 3   ScanFront Setup
❏Network Settings
Under Network Settings, configure the device name and IP 
address needed to connect the scanner to a network.
IMPORTANT
 Configure network settings while the network cable is 
connected to the scanner. If the network cable is not 
connected to the scanner, you will not be able to verify or 
modify settings in the network settings screen.
 The device name is the name for the scanner used on the 
network. When changing this setting, make sure to select a 
unique name that is different from those of all other devices.
 The device name can be a combination of letters (A-Z, a-z), 
numbers (0-9), and hyphens (-) up to 15 characters long.
 The device name must begin with a letter. You cannot end the 
device name with a hyphen.
 When a DHCP server is not used to assign IP addresses, 
clear the [DHCP server Enable] check box, and enter a fixed 
address. For details, contact your network administrator.
 If the DHCP server is enabled and the DNS server and WINS 
server information is not obtained properly, clear the 
[Automatic retrieval of DNS (WINS) server] check box, and 
enter the appropriate server addresses. 
 To send image files to devices or shared folders on a different 
segment of the network, you must incorporate a computer on 
which ScanFront Service is installed onto the network.
❏Administrator Password
Set the password required to log in to [Administrator 
setting] and the Web Menu (Administrator Mode).
CAUTION
Be careful with the administrator password. If you forget the 
password, you will have to reformat the scanner, and all 
registered data will be lost. 
						

							3-10
Chapter 3   ScanFront Setup
❏Backup/Restore Setting Information
Back up/restore setting information using a shared folder 
on the network or USB memory device at the following 
times. 
When adding another ScanFront
When adding, for instance, another ScanFront, back up the 
setting information that was set on the first ScanFront, and 
then restore the setting information on the other 
ScanFront. 
When updating the version of the ScanFront
Back up the setting information before you update the 
version of the ScanFront, and then restore the setting 
information after the version update is finished. 
When submitting the ScanFront for repairs
Before you submit the ScanFront for repairs, back up the 
setting information of the ScanFront. 
IMPORTANT
Before you submit the ScanFront for repairs, back up the setting 
information and then initialize the ScanFront. (See “Initializing 
ScanFront” on p. 10-13.)
Hint
 Scanner setting information can be backed up to a folder on a 
USB memory device if the device is inserted when [Backup / 
Restore all settings] is pressed.
 Backup / Restore all settings can also be configured from the 
[System Settings] screen (see p. 6-39) of the Web Menu 
(Administrator Mode).
❏Select Login Type
Set the screen that appears when users log in.
For details, see “Login Screen” on p. 5-4. 
						

							3-11
Chapter 3   ScanFront Setup
❏Roller Counter Reset
Reset the counter after replacing the feed roller when the 
scanner no longer feeds properly. For details, see 
“Replacing the Rollers and Document Holding Guide” on 
p. 9-8.
❏Format ScanFront
Initialize the ScanFront clears all the settings registered to 
the ScanFront.
Initialize the ScanFront at the following times. For details, 
see “Initializing ScanFront” on p. 10-13.
When submitting the ScanFront for repairs
Before you submit the ScanFront for repairs, initialize the 
ScanFront to protect the saved user information. 
When changing the operating environment
Delete all the user information registered on the ScanFront 
when, for instance, the users have changed because you 
have changed the installation location.
❏Touch Panel Adjustment
You can adjust the touch panel when it does not operate as 
expected. For details, see “Adjusting the Touch Panel” on 
p. 10-11.