Canon Projector WUX4000 User Manual

121
Installing / Removing the Lens Unit
Installation Manual Installation
5Then turn the projector back over and remove the sleeve.
6Referring the following illustration, insert the  lens connector of the lens unit into the 
front right side of the projector slowly until it  contacts the end. At this time, pull out the 
lens cable shown in the illustration and fix it.
7Tighten the 4 screws to fasten the lens unit in place.
The 4 lens unit screws are attached to  the lens unit and cannot be removed.
Lens...

Installing / Removing the Lens Unit
122
8Insert the projector lens cable into the connector until a click sound is heard.
9Return the sleeve, cosmetic panel, and lamp cover to their original conditions.
When the power is first turned on after the l ens unit has been installed or replaced, lens shift 
initialization operation will be performed. It will  take approximately 1 minute for the initializa-
tion operation to start up. However, if the lens has been replaced with a lens of the same 
model number,...

123
Installing / Removing the Lens Unit
Installation Manual Installation
■Removing the Lens Unit
1Perform steps 1 to 5 of “Installing the Lens Unit” ( P119 – P121) and remove the 
sleeve.
2Disconnect the lens cable from the lens connector.
3Fix the lens cable as shown in the illustration and loosen the 4 screws to remove the 
lens unit.
The 4 lens unit screws are attached to  the lens unit and cannot be removed.
When pulling out (disconnecting) the lens cable, pr ess the buttons on both sides of the lens...

124
Setting Up the Projector
■Positioning the Projector in Front of the Screen
Place the projector in front of the screen.
■Relationship Between Image Si ze and Projecting Distance
The projected image size is determined by  the distance between the projector and the 
screen (projection distance) as well as the  zoom. Refer to the table below and decide the 
distance between the projector and screen.
• Be sure to place the projector parallel 
to the screen to ensure distortion-free 
projection.
 The...

125
Setting Up the Projector
Installation Manual Installation
* H1 and H2 are the distances when the lens shift is the default value (listed below).Standard Zoom Lens, Long Zoom Lens : Up / down +50%, left / right 0%
Short Fixed Lens: Up / down / left / right 0%
Lens unitDiagonal 
when 
16:10
(diagonal) Image size (cm) Projection distance Distance from optical 
axis when projection is perpendicular to screen* (cm)
16:10 16:9 4:3 Wide limit Tele limit
Width Height Width Height Width Height m (feet) m...

Setting Up the Projector
126
■Lens Shift Function
The projector includes a lens shift function.  Operation of the buttons slides the lens up, 
down, left, and right, moving the image posi tion. For the function operations, refer to 
“Adjusting the Image Position” ( P60).
The amount of lens shift is indicated as a percentage relative to the image height and 
width. The amounts of lens shift for the St andard Zoom Lens and Long Zoom Lens is 
+55% (up), -15% (down), and ±10% (left / ri ght). With the Short...

127
Setting Up the Projector
Installation Manual InstallationArea where lens movement is not possible
With the Standard Zoom Lens and Long Zoom Lens, when the shift exceeds 44% in the 
upward direction, the amount of  available shift in the left / right directions decreases. 
When the lens is shifted upward to the maxi mum (55%), the amount of available shift in 
the left / right direction is ±2%.
With the Short Fixed Lens, great er shift in the up / down direction reduces the available 
shift in the...

128
Connecting to AV Equipment
■Connectable Equipment and Input Terminals
HDMI Use this name to select the image inpu t. Direction of signal and data flow
HDMI IN  terminal The name of the terminal to which to 
connect equipment.
(
Pxxx ): indicates the page(s) to refer to.
Computer ( P40) AV equipment (
P42)
Digital video camera* ( P42)
Computer (
P39, P40 )
AV equipment ( P43)
( P132)
(P39 , P40 , 
P43 )
( P40 )
DVI-D IN terminal can 
only be used to connect  to a PC.
(P41 , P44 )
Computer (
P41)
*...

129
Connecting to AV Equipment
Installation Manual Installation
■Connection Terminal and Connection Cable
Input signal Input terminal Types of connection cables
HDMI HDMI cable (not included)
Digital PC DVI-D cable (not included)
Analog PC /
COMPONENT IN VGA cable (supplied item)
BNC cable (not included)
Component /
COMPONENT IN Component cable (not included)
BNC cable 
(not included)Mini D-sub 15-pin - BNC terminal 
converter cable (not included)
D terminal plug - RCA plug 
component converter cable...

130