Canon Projector WUX4000 User Manual

141
Network Settings on the Projector
Installation Manual Connecting to a Networ
k
TCP / IP Setting
[TCP/IP setting]
Configure the projector TCP / IP settings.
When [TCP/IP setting] is selected, the win-
dow shown below appears. Use the 
[] / 
[ ] buttons to select the IP address, then 
press the  OK button. Next, use the [ ] 
and [ ] buttons to select the digit and the 
[] / [ ] buttons to change the value. 
Press the  OK button, then set the subnet 
mask and gateway address in the same 
way. Finally,...

142
Configuring the Network From the Computer
■Displaying and Configuring the Network Configuration Screen
1Turn on the computer and projector.
2Launch a web browser, enter “http://(proje ctor IP address)” in the address bar, and 
press the Enter key.
The password input screen appears.
3Enter the user name and password on the password input screen, then click OK.
The factory defa ult user name is “root” an d the password is “system”.
The projector web screen appears in the web browser.
The factory...

143
Configuring the Network From the Computer
Installation Manual Connecting to a Networ
k
The following information is displayed.
4To configure, click [Settings]. 
The settings window appears.
Projector name The name of the projector on the network
Location The location of projector installation
MAC address The MAC address of the projector
IP address The IP address of the projector
Power Status The power status of the projector
Lamp Time Normal Mode Lamp operating time in [Normal] lamp mode
Lamp Time...

Configuring the Network From the Computer
144
5Select the function to set from the menu  (1), then enter the setting in the displayed 
field (2) and click [OK] (3).
6A confirmation window appears. Check the  contents and if they are correct, click 
[Apply].
The settings are applied to the projec tor and “Save completed” is displayed.
7Click [Back to top] to return the web screen to the initial page.
(2)
(1)
(3) 

145
Configuring the Network From the Computer
Installation Manual Connecting to a Networ
k
■Resetting to Factory Defaults
1Perform steps 1 - 3 of “Displaying and Conf iguring the Network Configuration Screen” 
(P142 ) to display the setting window.
2Click [Initialize].
3A confirmation window appears. Click [OK]. 
■Setting Errors
When a setting-related error occurs, the erro r name is displayed on the screen, and a 
“!” mark is displayed next to the input field which caused the error. 

Configuring the Network From the Computer
146
The error meanings are as shown below.
ErrorMeaning
Input error A setting outside the valid range was set on the 
setting screen.
Password setting error The set password and confirmation password did 
not match.
Invalid SMTP The SMTP server IP address has not been set.
System failed to connect SMTP 
server. Failed to connect to the SMTP server when send-
ing a test mail.
System failed to connect POP3 
server. Failed to connect to the POP3 server attempting to...

147
Installation Manual Connecting to a Networ
k
Setting Up the Network
■Setting Basic Information [Network]
From [Network] in the settings window, you can log into the web screen and set basic 
network information. For the setting proced ure, refer to “Displaying and Configuring 
the Network Configuration Screen” ( P142). 
ItemExplanationFactory default setting
Password
User  name When logging into the web screen, 
enter the user name in 1-byte 
alphanumeric characters and 
symbols (4 -15 characters)....

Setting Up the Network
148
■Setting Up Email [Mail]
From [Mail] in the settings window, you c an set the items necessary to send error 
mails and test mails. For the setting proce dure, refer to “Displaying and Configuring 
the Network Configuration Screen” ( P142). 
ItemExplanationFactory default setting
To: Enter the recipient address for error 
mails in 1-byte alphanumeric char-
acters and symbols (1 - 63 charac-
ters). MailUserAccount
Cc: Enter the CC address for error mails 
in 1-byte alphanumeric...

149
Setting Up the Network
Installation Manual Connecting to a Networ
k
■Mail Authentication Settings [Mail auth]
From [Mail auth] in the settings window,  you can configure the settings for authentica-
tion of mail that is sent when an error occ urs. For the setting procedure, refer to “Dis-
playing and Configuring the Network Configuration Screen” ( P142). 
ItemExplanationFactory default set-
ting
Mail  authentication Select the mail authentication method.  If OFF is selected, the other mail...

Setting Up the Network
150
■Sending a Test Mail [Send test mail]
From [Send test mail] in the settings wi ndow, you can send a test mail to the mail 
address that was set in [Mail]. The settings cannot be changed from this window.
■ SNMP Settings [SNMP]
From [SNMP] in the settings window, you can  configure the settings related to control 
of projectors which use SNMP (Simple Ne twork Management Protocol). For the set-
ting procedure, refer to “Displaying an d Configuring the Network Configuration...