Canon Projector WUX4000 User Manual

							141
Network Settings on the Projector
Installation Manual Connecting to a Networ
k
TCP / IP Setting
[TCP/IP setting]
Configure the projector TCP / IP settings.
When [TCP/IP setting] is selected, the win-
dow shown below appears. Use the 
[] / 
[ ] buttons to select the IP address, then 
press the  OK button. Next, use the [ ] 
and [ ] buttons to select the digit and the 
[] / [ ] buttons to change the value. 
Press the  OK button, then set the subnet 
mask and gateway address in the same 
way. Finally, select [Enter].
• The factory defaults are shown below.
IP address 192.168.254.254
Subnet mask 255.255.255.0
Gateway address 0.0.0.0
 Setting cannot be made when [DHCP]  (P140 ) is [On].
 If an invalid value is entered, the message  “Invalid entry” appears. If this occurs, 
enter a valid value.
Initializing Network Settings
[Network setting initialization]
You can initialize the projector network set-
tings.
When [Network setting initialization] is 
selected, the  window shown below 
appears. Select [YES] then press the  OK 
button.
 The following items are initialized.
Network Password setting
Register Network Password
PJLink
DHCP
IP address
Subnet mask
Gateway address
E-mail sender address
E-mail recipient address
Projector name
Location
Network Setting
TCP/IP setting
Network Setting
Network setting initialization 
						

							142
Configuring the Network From the Computer
■Displaying and Configuring the Network Configuration Screen
1Turn on the computer and projector.
2Launch a web browser, enter “http://(proje ctor IP address)” in the address bar, and 
press the Enter key.
The password input screen appears.
3Enter the user name and password on the password input screen, then click OK.
The factory defa ult user name is “root” an d the password is “system”.
The projector web screen appears in the web browser.
The factory default IP address is “192.168.254.254”. If DHCP settings are used, ask the net-
work administrator for the projector IP address.  It is possible to check the IP address from 
the projector menu. 
						

							143
Configuring the Network From the Computer
Installation Manual Connecting to a Networ
k
The following information is displayed.
4To configure, click [Settings]. 
The settings window appears.
Projector name The name of the projector on the network
Location The location of projector installation
MAC address The MAC address of the projector
IP address The IP address of the projector
Power Status The power status of the projector
Lamp Time Normal Mode Lamp operating time in [Normal] lamp mode
Lamp Time Quiet Mode Lamp operating time in [Quiet] lamp mode
Lamp Time Converted Lamp operating time (converted value)
Filter Time Filter operating time
Alert Error message (if an error has occurred)
Temperature abnormality
Faulty lamp
Faulty lamp cover
Faulty cooling fan
Faulty power supply
Faulty lens connector: Lens connector error
Faulty air filter unit: Filter error
Unknown error
To operate the projector from the computer, click [Projector control] ( P153). 
						

							Configuring the Network From the Computer
144
5Select the function to set from the menu  (1), then enter the setting in the displayed 
field (2) and click [OK] (3).
6A confirmation window appears. Check the  contents and if they are correct, click 
[Apply].
The settings are applied to the projec tor and “Save completed” is displayed.
7Click [Back to top] to return the web screen to the initial page.
(2)
(1)
(3) 
						

							145
Configuring the Network From the Computer
Installation Manual Connecting to a Networ
k
■Resetting to Factory Defaults
1Perform steps 1 - 3 of “Displaying and Conf iguring the Network Configuration Screen” 
(P142 ) to display the setting window.
2Click [Initialize].
3A confirmation window appears. Click [OK]. 
■Setting Errors
When a setting-related error occurs, the erro r name is displayed on the screen, and a 
“!” mark is displayed next to the input field which caused the error. 
						

							Configuring the Network From the Computer
146
The error meanings are as shown below.
ErrorMeaning
Input error A setting outside the valid range was set on the 
setting screen.
Password setting error The set password and confirmation password did 
not match.
Invalid SMTP The SMTP server IP address has not been set.
System failed to connect SMTP 
server. Failed to connect to the SMTP server when send-
ing a test mail.
System failed to connect POP3 
server. Failed to connect to the POP3 server attempting to 
send a test mail.
System doesnt support this auth 
type. An authentication type was set which is not sup-
ported by the server.
System failed to authenticate. Authentication failed attempting to send a test mail.
The system failed to send the test 
mail. Sending of test mail failed due to a connection fail-
ure with the SMTP server or an error which does 
not ordinarily occur.
Save Failed Mismatch in settings occurred when settings were 
changed at the same time from multiple comput-
ers. 
						

							147
Installation Manual Connecting to a Networ
k
Setting Up the Network
■Setting Basic Information [Network]
From [Network] in the settings window, you can log into the web screen and set basic 
network information. For the setting proced ure, refer to “Displaying and Configuring 
the Network Configuration Screen” ( P142). 
ItemExplanationFactory default setting
Password
User  name When logging into the web screen, 
enter the user name in 1-byte 
alphanumeric characters and 
symbols (4 -15 characters). root
New  password When logging into the web screen,  enter the password in 1-byte 
alphanumeric characters and 
symbols (4 -15 characters). system
Confirm new password For confirmation, enter the same  password that you entered in [New 
password]. system
TCP/IP
DHCP Select whether to turn the DHCP 
function on or off. If the function is 
on, because the IP address is 
acquired from the server, it is not 
possible to enter the [IP address], 
[Subnet mask], and [Default gate-
way]. OFF
IP address Enter the IP address of the projec- tor in 1-byte numbers. 192.168.254.254
Subnet mask Enter the subnet mask in 1-byte  numbers. 255.255.255.0
Default gateway Enter the default gateway IP  address in 1-byte numbers. 0.0.0.0
If settings related to TCP / IP were changed, it is necessary to disconnect and reconnect to 
the network. If the network subnet mask was 
changed, select [Subnet mask] in the above 
window and set the new subnet mask. 
						

							Setting Up the Network
148
■Setting Up Email [Mail]
From [Mail] in the settings window, you c an set the items necessary to send error 
mails and test mails. For the setting proce dure, refer to “Displaying and Configuring 
the Network Configuration Screen” ( P142). 
ItemExplanationFactory default setting
To: Enter the recipient address for error 
mails in 1-byte alphanumeric char-
acters and symbols (1 - 63 charac-
ters). MailUserAccount
Cc: Enter the CC address for error mails 
in 1-byte alphanumeric characters 
and symbols (1 - 63 characters). 
From: Enter the sender address for error 
mails in 1-byte alphanumeric char-
acters and symbols (1 - 63 charac-
ters). [email protected]
SMTP server IP address Enter the SMTP server IP address in  1-byte numbers. 0.0.0.0
SMTP server port number Enter the SMTP server port number  in 1-byte numbers (1 - 65535). 25
SNTP server IP address Enter the SNTP server IP address in  1-byte numbers. 0.0.0.0
Time zone Select the time zone where the pro-
jector is used. (GMT) Dublin, Lisbon, 
London
Mail resend interval Enter the interval for resending mail 
when an error occurred (units: sec-
onds) within the range of 0 - 59 sec-
onds using 1-byte numbers. 10
Mail resend times Enter the number of times to resend 
mail when an error occurred within 
the range of 0 - 255 using 1-byte 
numbers. 3
Error report Select whether to turn the error mail 
sending function on or off.  OFF 
						

							149
Setting Up the Network
Installation Manual Connecting to a Networ
k
■Mail Authentication Settings [Mail auth]
From [Mail auth] in the settings window,  you can configure the settings for authentica-
tion of mail that is sent when an error occ urs. For the setting procedure, refer to “Dis-
playing and Configuring the Network Configuration Screen” ( P142). 
ItemExplanationFactory default set-
ting
Mail  authentication Select the mail authentication method.  If OFF is selected, the other mail 
authentication settings cannot be 
changed. OFF
User name Enter the user name to use for mail  authentication in 1-byte alphanu-
meric characters and symbols (1 - 63 
characters). 
Password Enter the password for mail authenti- cation in 1-byte alphanumeric charac-
ters and symbols (1 - 63 characters). 
Confirm password  For confirmation, enter the same  password as you entered in [Pass-
word]. 
POP3 server IP address Enter the POP3 server IP address in  1-byte numbers. 0.0.0.0
POP3 server port number Enter the POP3 server port number in  1-byte numbers (1 - 65535). 110
POP before SMTP response time Enter the wait time from POP3 authen- tication to SMTP authentication (units: 
milliseconds) using 1-byte numbers 
(0 - 9999 milliseconds). 300 
						

							Setting Up the Network
150
■Sending a Test Mail [Send test mail]
From [Send test mail] in the settings wi ndow, you can send a test mail to the mail 
address that was set in [Mail]. The settings cannot be changed from this window.
■ SNMP Settings [SNMP]
From [SNMP] in the settings window, you can  configure the settings related to control 
of projectors which use SNMP (Simple Ne twork Management Protocol). For the set-
ting procedure, refer to “Displaying an d Configuring the Network Configuration 
Screen” ( P142). 
ItemExplanation
To :
The recipient address which was set from [Mail] in the settings window 
(
P148) is displayed.
Cc:
The CC address which was set from [Mail] in the settings window (P148) 
is displayed.
From:
The sender name which was set from [Mail] in the settings window 
(
P148) is displayed.
Subject:
The predetermined mail title “Canon Projector test” is displayed.