Canon projector LXMU800Z User Manual

85
Extension Pipe RS-CL08 / RS-CL09 (Optional)
Use an optional extension pipe (RS-CL08 / RS-CL09) according to the ce\
iling height. For details, 
contact our local agent.
RS-CL08
Outer/inner pipes and outer/inner covers
M5 screw (12 mm/0.5”): 4 pcs.
M3 screw (10 mm/0.4”): 1 pc.
The length is adjustable between 35 cm/1.1’
and 55 cm/1.9’ in steps of 5 cm/0.2’.
RS-CL09
Outer/inner pipes and outer/inner covers
M5 screw (12 mm/0.5”): 4 pcs.
M3 screw (10 mm/0.4”): 1 pc.
The length is adjustable between 55...

86
Distance from Ceiling to Lens Center (ℓ)
RS-CL15When RS-CL08 is used When RS-CL09 is used
24.6 cm / 0.8’59.6 cm / 2.0’ to 79.6 cm / 2.6’79.6 cm / 2.6’ to 119.6 cm / 3.9’
For more detailed information on the screen sizes and the projection dis\
tance, see “Relationship 
Between Image Size and Projecting Distance” on page 96.
Ceiling-mount Bracket
100 mm/ 3.9 100 mm
/ 3.9
80 mm / 3.1 80 mm
/ 3.1
100 mm / 3.9 100 mm
/ 3.9
80 mm
/ 3.1 80 mm
/ 3.1
Assembly and Installation
Installation to Flat and Level...

87
3. Turn the projector base up, and remove the two 
adjusting legs on front side.
4. Install the attached M4 screws at the six screw fastening 
positions on the Base bracket.
Caution:
 ■Make sure to remove the adjusting foot before attaching 
the screw to the front part of the projector.
 ■Be sure to keep the removed adjusting foot safely for 
later use.
5. Secure the terminal clamp of the Anti-fall wire with the 
attached M4 screw at (A) on the Base bracket.
Make sure to fasten and tighten the screw...

88
Installation to a High Ceiling
Use optional extension pipe RS-CL08 or RS-CL09 for high ceiling.
Preparation:
1. Remove the covers of outer and inner pipes by slightly 
sliding them and lift up as shown.
2. Remove four M5 screws from the sides of the outer 
pipe, adjust the inner pipe length according to the 
projector installation height, and then secure the four M5 
screws.
When attaching screws in step 2, insert the screws and 
leave an unused screw hole between them. When the 
extension pipe is...

89
1. Make a hole in the ceiling to install the ceiling-mount 
bracket and cables.
Caution:
 ■Mounting position varies on the projector used. Make 
sure that the template sheet (A) corresponding to the 
projector is used.
 ■When determining the hole position, use the supplied 
template sheet (A).
 ■The direction to the screen is indicated on the template 
sheet (A).
2. Use four M13 screws, to secure the ceiling-mount 
bracket to the ceiling with the arrow facing toward the 
screen.
 ■Before securing the...

90
7. Use the four M5 screws removed from the ceiling-mount 
bracket during preparation.
Direction to the 
screen
8. Hook the base bracket on the protrusion (A) of the joint 
fitting, and secure it temporarily using the four supplied 
M5 screws (B).
9. Mount the terminal clamp on the other end of anti-fall 
wire to the joint fitting (C), and secure it at the wire-
attaching position using M4 screw.
 ■Pull out the cables.
 ■Be sure to secure screws (B) tightly after making 
the adjustment discussed in...

91
Adjust the Projection Angle
Turn on the projector, project an image, and then adjust the projection angle and screen slan\
t angle.
Caution:
 ■After completion of adjustment, tighten the screws and check that every fitting is secured firmly.
 ■Be sure to hold the projector from falling until the ceiling-mount brack\
et and Base bracket are 
secured firmly.
Adjust the horizontal 
projection angle
Adjust the screen slant 
angleAdjust the vertical 
projection angle
A
D B
C
Adjust the Horizontal...

92
Specifications
RS-CL15
Adjustment range
Horizontal projection angle5° leftward or rightward
Vertical projection angle5° upward or 20° downward
Screen slant angle± 5°
Outer dimension of assembly 
(excluding projection) (W x D x H)460 x 490 x 152.6 mm (18.1 x 19.3 x 6.0 in)
Weight (Ceiling attachment only)6.9 kg (15.2 lbs)   

93
Troubleshooting
Image Problems
Problem: No image appears on the screen.
1. Check whether the projector is connected to the computer or AV equipment correctly.
2. Check whether the power cord is connected correctly.
3. Turn first the projector and then the computer off and then back on again.
Problem: The image is blurred.
1. Adjust the Focus on the projector.
2. Press the AUTO PC button on the remote control.
3. Ensure the projector-to-screen distance is within the specified range.
4. Check that the...

94
Specifications
Product Specifications
Model nameLX-MU800ZLX-MU600Z
Display system1-CHIP DLP™
Display device
TypeDMD
Size / Aspect ratio0.67”x1 / 16:10
Drive systemDLP™ x 1 chip
Number of pixels2,304,000 (1920 x 1200) x 1
Projection lens
 
(*1) (*2)
Zoom ratio / Focal length /  
F number
1.3x / f = 26 to 34mm / F = 1.64 to 1.86
Zooming / Focusing systemElectric / Electric
Lens shift (motorized)Adjust range:
V (down: 30% ~ up: 60%), H (left: 10% ~ right: 20%)
Optical performance guaranteed range:
V...