Canon printer Color imageCLASS MF9280Cdn User Manual

2-8
Paper Requirements
Originals and Print Media
To prevent paper jams, do not use any of the following:
Wrinkled or creased paper
Curled or rolled paper
Torn paper
Damp paper
Very thin paper
Paper which has been printed on using a thermal transfer printer (Do not copy on the reverse side.)
The following types of paper do not print well:
Highly textured paper
Very smooth paper
Shiny paper
Make sure the paper is free from dust, lint, and oil stains.
Be sure to test paper before purchasing large...

2-9
Printable Area
Originals and Print Media

Printable Area
The shaded area indicates the approximate printable area of LTR paper. Note that the 
margin widths listed are approximate and there may be slight variations in actual use. 

2-10
Loading Paper
Originals and Print Media

Loading Paper
This section describes how to load paper in the paper drawers and stack bypass tray.
Handle paper carefully not to cut your hands with the edges of the paper.When installing or removing cassettes, be careful not to get your fingers caught.
In the Paper Drawer
This section describes how to load paper in the paper drawer or in the optional paper drawer.
––
1 
Pull out the paper drawer until it stops.
2 
Hold the paper drawer with both hands 
and...

2-11
Loading Paper
Originals and Print Media

4 
Hold the lock release lever of the rear 
paper guides (A) and slide the guides to 
the mark for the size of the paper to be 
loaded.
Make sure to set the guides to the mark for the size of the paper to be loaded correctly. If the guides are positioned incorrectly, it may cause paper jams, dirty prints, etc.
5 
Fan the paper stack and even the edges.
6 
Load the paper stack of the appropriate 
size with the print side facing up. Align 
the rear edge of the...

2-12
Loading Paper
Originals and Print Media
7 
Hold the paper drawer with both hands 
and set it back into the machine.8 
Push the paper drawer as far as it will go.
For details on loading paper in the stack bypass tray, see “In the Stack Bypass Tray,” on p. 2-16.
In the Optonal Paper Drawer (Paper Drawer 2)
When the optional drawer is installed in the machine, follow the procedure described below.
●
1 
Pull out the optional paper drawer until it 
stops.
2 
Hold the optional paper drawer with both...

2-13
Loading Paper
Originals and Print Media

4 
Hold the lock release lever of the rear 
paper guides (A) and slide the guides to 
the mark for the size of the paper to be 
loaded.
Make sure to set the guides to the mark for the size of the paper to be loaded correctly. If the guides are positioned incorrectly, it may cause paper jams, dirty prints, etc.
5 
Fan the paper stack and even the edges.
6 
Load the paper stack of the appropriate 
size with the print side facing up. Align 
the rear edge of...

2-14
Loading Paper
Originals and Print Media

8 
Push the paper drawer as far as it will go.
For details on loading paper in the stack bypass tray, see “In the Stack Bypass Tray,” on p. 2-16. 

2-15
Loading Paper
Originals and Print Media

 
When prntng paper wth a letterhead or logo (preprnted paper) usng the paper 
drawer:
Load the paper in the proper orientation as follows.
Portrait orientationLandscape orientation
1-sided printing
(When  in  
is set to  (the 
default setting))
For details, see “Introduction of 
the Machine,” in the e-Manual.
(with the printing side facing up)(with the printing side facing up)
1-sided printing
(When  in  
is set to )
For details,...

2-16
Loading Paper
Originals and Print Media

In the Stack Bypass Tray
If you are making prints on transparencies, labels, nonstandard-sized paper, or envelopes, load them into the 
stack bypass tray.
Note the following points when using the stack bypass tray:Paper Quantity: one to approximately 100 sheets (20 lb (75 g/m2),)
Paper Size: 3" × 5" to 8 1/2" × 14" (76.2 × 127 mm to 216 × 356 mm )
Paper Weight: 16 to 47 lb (60 to 176 g/m
2)Paper which has been rolled or curled must be...

2-17
Loading Paper
Originals and Print Media

1 
Open the stack bypass tray.
If the paper size you are going to load into the stack bypass tray is different from the paper size stored in stack bypass tray Standard Settings, set stack bypass tray Standard Settings to ‘Off ’ in Common Settings (from the Additional Functions screen). (See “Setting Paper Size and Type,” on 
p. 2-22.)
2 
Adjust the slide guides to match the size 
of the paper.
If you are feeding large size paper, pull out the 
auxiliary...