Canon printer Color imageCLASS MF9280Cdn User Manual

Copying
4-4
Basic Copying Method

Basic Copying Method
This section describes the basic procedure for copying.
1 
Place originals on the platen glass or load 
it them in the feeder.
For details, see “Placing Originals,” on p. 2-4.
Close the feeder after placing your originals.
For originals you can copy, see “Originals 
Requirements,” on p. 2-
2.
When the display shows the message , enter the department ID and 
password. Then press  (Log In/Out) on the 
control panel. For details, see “Security” in the...

Copying
4-5
Basic Copying Method
: Reduces 
multiple originals to fit on one sheet of paper. 
(See “Multiple Originals onto One Sheet (N on 
1),” on p. 4-3
7.)
: Adjusts the contrast of 
the originals. (See “Adjusting Sharpness,” on 
p. 4-4
2.)
: Erases 
unnecessary shadows and lines. (See “Erasing 
Shadows/Lines,” on p. 4-4
4.) 
: Adjusts the color 
balance for the copy. (See “Adjusting Color 
Balance,” on p. 4-5
4.) 
: Sorts copies into sets. 
(See  “Collating Copies,” on p. 4-60.)
: Makes ID card...

Copying
4-6
Canceling Copy Jobs

Canceling Copy Jobs
You can cancel scanning or ongoing jobs.
If you cancel a copy job during scanning, make sure to remove the original.
1 
Press the left Any key to select .
The display will return to the Copy top screen.
 While the machine is scanning, printing, or waiting to print, you can cancel a copy job by pressing  (Stop).
2 
Press  (Main Menu) to return to the 
Main Menu screen. 

Copying
4-7
Selecting Color Mode

1 
Set originals.
For details, see “Placing Originals,” on p. 2-4.
2 
Press  (Main Menu).
3 
Use [▼], [▲] or  (Scroll Wheel) to select 
, then press [OK].
4 
Use [▼], [▲] or  (Scroll Wheel) to 
display , then 
press [OK].
5 
Use [▼], [▲] or  (Scroll Wheel) to select 
the color mode, then press [OK].
: For the automatic 
selection of color or B&W*
: For copies in full-color
: For black and white copies
*   Depending on the condition of the originals, 
the machine may not...

Copying
4-8
Selecting Color Mode
6 
Use – (numeric keys) to enter the 
desired copy quantity (1 to 99).
7 
Press  (Start).
If you want to copy multiple originals using the 
platen glass, set an original and press  (Start) 
once for each page.
8 
Press  (Main Menu) to return to the 
Main Menu screen. 

Copying
4-9
Selecting Paper Source

Selecting Paper Source
You can manually specify a paper source.  
The default setting is .
If you are copying an original with an image that extends all the way to the edges onto the same size paper at a copy ratio of 100%, the periphery of the original image may be cut off slightly on the copy. For details, see “Scanning Area,” on p. 11-4.The suffix  (such as in STMTR), used in paper size designations, indicates that the paper is loaded in a paper drawer or the stack...

Copying
4-10
Selecting Paper Source
5 
Use [▼], [▲] or  (Scroll Wheel) to select 
the desired paper source, then press [OK].
6 
Use – (numeric keys) to enter the 
desired copy quantity (1 to 99).
7 
Press  (Start).
If you want to copy multiple originals using the 
platen glass, set an original and press  (Start) 
once for each page.
8 
Press  (Main Menu) to return to the 
Main Menu screen. 

Copying
4-11
Selecting Paper Source

1 
Set originals.
For details, see “Placing Originals,” on p. 2-4.
2 
Press  (Main Menu).
3 
Use [▼], [▲] or  (Scroll Wheel) to select 
, then press [OK].
4 
Load the paper into the stack bypass tray.
5 
Use [▼], [▲] or  (Scroll Wheel) to select 
the desired paper size, then press [OK].
You can select from the following paper sizes:
, , , , , 
, , , , 
For details, see “Paper Requirements,” on p. 2-7.
The available paper sizes will vary depending on the country where...

Copying
4-12
Selecting Paper Source
6 
Use [▼], [▲] or  (Scroll Wheel) to select 
the desired paper type, then press [OK].
You can select from the following paper types:
, , , 
, , , , 
, 
For details, see “Paper Requirements,” on p. 2-7.
If you want to print the back side of the printed paper, press the right Any key to select .
7 
Press [OK] to select .
The selected paper size is displayed next to 
.
8 
Use – (numeric keys) to enter the 
desired copy quantity (1 to 99).
9 
Press  (Start).
If you want...

Copying
4-13
Selecting Paper Source

1 
Set originals.
For details, see “Placing Originals,” on p. 2-4.
2 
Press  (Main Menu).
3 
Use [▼], [▲] or  (Scroll Wheel) to select 
, then press [OK].
4 
Load the paper into the stack bypass tray.
5 
Use [▼], [▲] or  (Scroll Wheel) to select 
, then press [OK].
6 
Press [OK] to select the horizontal length 
.
Using Stack Bypass Tray with Irregular Sizes of Paper
This section describes how to copy onto non-standard-sized paper using the stack bypass tray.
If...