Canon printer Color imageCLASS MF8350Cdn User Manual

							
xv
telephone company. The REN for this product is part of the 
product identifi er that has the format US: AAAEQ##T XXXX. The 
digits represented by ## are the REN without a decimal point 
(e.g., 10 is a REN of 1.0).
An FCC compliant telephone line cable and modular plug is 
provided with this equipment. This equipment is designed to 
be connected to the telephone network or premise wiring us-
ing a compatible modular jack that is Part 68 compliant.
This equipment may not be used on coin service provided by 
the telephone company. Connection to party lines is subjected 
to state tariff  s.
In Case of Equipment Malfunction
Should any malfunction occur which cannot be corrected 
by the procedures described in this guide or the e-Manual, 
disconnect the equipment from the telephone line cable and 
disconnect the power cord.
The telephone line cable should not be reconnected or the 
main power switch turned ON until the problem is completely 
resolved. Users should contact Canon Authorized Service 
Facilities for servicing of equipment, Information regarding 
Authorized Service Facility locations can be obtained by calling 
Canon Customer Care Center (1-800-OK-CANON).
Rights of the Telephone Company
If this equipment (Color imageCLASS MF8350Cdn/MF8050Cn) 
causes harm to the telephone network, the telephone 
company may temporarily disconnect service. The telephone 
company also retains the right to make changes in facilities 
and services that may aff   ect the operation of this equipment. 
When such changes are necessary, the telephone company is 
required to give adequate prior notice to the user.
However, if advance notice is not possible, the telephone 
company will notify the customer as soon as possible. Also, 
the customer will be advised of his/her right to fi  le a complaint 
with the FCC if he/she believes it is necessary.
     WARNING     
The Telephone Consumer Protection Act of 1991 makes it 
unlawful for any person to use a computer or other electronic 
device, including FAX machines, to send any message unless 
such message clearly contains in a margin at the top or bottom 
of each transmitted page or on the fi  rst page of the transmis-
sion, the date and time it is sent and an identifi  cation of the 
business or other entity, or other individual sending the mes-
sage and the telephone number of the sending machine or 
such business, other entity, or individual.
(The telephone number provided may not be a 900 number or 
any other number for which charges exceed local or long-dis-
tance transmission charges.)
    NOTE 
In order to program this information into your machine, you 
should complete the procedure for registering your name, 
unit’s telephone number, time, and date in the Starter Guide.
6TFST
JO
$BOBEB
Pre-Installation Requirements for Canon Facsimile Equipment
A. Location
Supply a suitable table, cabinet, or desk for the machine. 
See Chapter 11, “Appendix,” for specifi  c dimensions and 
weight.
B. Order Information 1. A single telephone line (touch-tone or rotary) should be used.
2. Order a CA11A modular jack, which should be installed  by the telephone company. If the CA11A jack is not 
present, installation cannot occur.
3. Order a normal business line from your telephone  company’s business representative. The line should be 
a regular voice grade line or an equivalent one. Use one 
line per unit.
DDD (Direct Distance Dial) line
-or-
IDDD (International Direct Distance Dial) line if you com-
municate overseas
    NOTE 
Canon recommends an individual line following industry 
standards, i.e., 2,500 (touch-tone) or 500 (rotary/pulse dial) 
telephones. A dedicated extension off    a PBX (Private Branch 
eXchange) unit without “Call Waiting” can be used with your 
facsimile unit. Key telephone systems are not recommended 
because they send nonstandard signals to individual tel-
ephones for ringing and special codes, which may cause a 
facsimile error.
C. Power Requirements
The power outlet should be a three-prong grounded re-
ceptacle (Single or Duplex). It should be independent from 
copiers, heaters, air conditioners, or any electric equipment 
that is thermostatically controlled. The rated value is 115 
volts and 15 amperes. The CA11A modular jack should be 
relatively close to the power outlet to facilitate installation.
Notice This product meets the applicable Industry Canada technical 
specifi  cations.
The Ringer Equivalence Number is an indication of the 
maximum number of devices allowed to be connected to 
a telephone interface. The termination of an interface may 
consist of any combination of devices subject only to the 
requirement that the sum of the RENs of all the devices does 
not exceed fi  ve.
The REN of this product is 1.0.
Before installing this equipment, users should ensure that 
it is permissible to be connected to the facilities of the local 
telecommunications company. The equipment must also 
be installed using an acceptable method of connection. In 
some cases, the company’s inside wiring associated with a 
single line individual service may be extended by means of 
a certifi  ed connector assembly (telephone extension cord). 
The customer should be aware that compliance with the 
above conditions may not prevent deterioration of service in 
some situations.
Repairs to certifi  ed equipment should be made by an 
authorized Canadian maintenance facility designated by 
the supplier. Any repairs or alterations made by the user to 
this equipment, or equipment malfunctions, may give the 
telecommunications company cause to request the user to 
disconnect the equipment.
•
•
•
•
• 
						

							
xvi
Users should ensure for their own protection that the elec-
trical ground connections of the power utility, telephone 
lines, and internal metallic water pipe system, if present, are 
connected together. This precaution may be particularly 
important in rural areas.
    CAUTION 
 Users should not attempt to make such connections them-
selves, but should contact the appropriate electric inspection 
authority, or electrician, as appropriate. 
    NOTE 
This equipment complies with the Canadian ICES-003 Class B 
limits.
6UJMJTBUJPO
BV
$BOBEB
Conditions à Remplir Préalablement à L’installation d’un 
Télécopieur Canon
A. EmplacementPrévoir une table, un meuble, ou un bureau suffi   samment 
solide et de taille appropriée (voir le chapitre 11, Annexe 
(Appendix), pour les indications de poids et dimensions).
B. Installation téléphonique 1. Une seule ligne téléphonique (tonalités ou impulsions) doit être utilisée.
2. Il faut commander un jack modulaire CA11A qui sera  installé par la compagnie téléphonique. Sans ce jack, la 
mise en place serait impossible.
3. Si vous vous abonnez à une nouvelle ligne, demandez  une ligne d’aff   aires normale de qualité téléphonique 
courante ou équivalente. Prenez un abonnement d’une 
ligne par appareil.
Ligne automatique interurbaine
ou
Ligne automatique internationale (si vous communiquez 
avec les pays étrangers)
    NOTE 
Canon vous conseille d’utiliser une ligne individuelle conforme 
aux normes industrielles, à savoir:
ligne téléphonique 2,500 (pour appareil à clavier) ou 500 
(pour appareil à cadran/impulsions). Il est également possi-
ble de raccorder ce télécopieur à un système téléphonique à 
poussoirs car la plupart de ces systèmes émettent des signaux 
d’appel non normalisés ou des codes spéciaux qui risquent de 
perturber le fonctionnement du télécopieur.
C. Condition d’alimentation
Raccordez le télécopieur à une prise de courant plus terre à 
trois branches, du type simple ou double, et qui ne sert pas 
à alimenter un copieur, un appareil de chauff   age, un clima-
tiseur ou tout autre appareil électrique à thermostat.
L’alimentation doit être de 115 volts et 15 ampères. Pour 
faciliter l’installation, le jack CA11A doit être assez proche 
de la prise de courant.
•
Remarques
Le présent matériel est conforme aux spécifi  cations tech-
niques applicables d’Industrie Canada.
Avant d’installer cet appareil, l’utilisateur doit s’assurer qu’il 
est permis de le connecter à l’équipement de la compagnie 
de télécommunication locale et doit installer cet appareil 
en utilisant une méthode de connexion autorisée. Il se 
peut qu’il faille étendre la circuiterie intérieure de la ligne 
individuelle d’abonné, qui a été installée par la compagnie, 
au moyen d’un jeu de connecteurs homologués (rallonge 
téléphonique).
L’attention de l’utilisateur est attirée sur le fait que le respect 
des conditions mentionnées ci-dessus ne constitue pas une 
garantie contre les dégradations de qualité du service dans 
certaines circonstances.
L’indice d’équivalence de la sonnerie (IES) sert à indiquer 
le nombre maximal de terminaux qui peuvent être rac-
cordés à une interface téléphonique. La terminaison d’une 
interface peut consister en une combinaison quelconque 
de dispositifs, à la seule condition que la somme d’indices 
d’équivalence de la sonnerie de tous les dispositifs n’excède 
pas 5.
Le nombre d’équivalents sonnerie (REN) de ce produit est 
1,0.
Les réparations sur un appareil certifi  é doivent être faites 
par une société d’entretien canadienne autorisée par le Gou-
vernement canadien et désignée par le fournisseur. Toute 
réparation ou modifi  cation que pourrait faire I’utilisateur de 
cet appareil, ou tout mauvais fonctionnement, donne à la 
compagnie de télécommunication le droit de débrancher 
I’appareil.
Pour sa propre protection, I’utilisateur doit s’assurer que les 
prises de terre de I’appareil d’alimentation, les lignes télé-
phoniques et les tuyaux métalliques internes, s’il y en a, sont 
bien connectés entre eux. Cette précaution est particulière-
ment importante dans les zones rurales
    CAUTION 
Au lieu d’essayer de faire ces branchements eux-mêmes, les 
utilisateurs sont invités à faire appel à un service d’inspection 
faisant autorité en matière d’électricité ou à un électricien, 
selon le cas.
    NOTE 
Respecte les limites de la classe B de la NMB-003 du Canada. •
•
•
•
•
•
• 
						

							
xvii
Laser Safety
This machine complies with 21 CFR Chapter 1 Subchapter J as 
a Class 1 laser product under the U.S. Department of Health 
and Human Services (DHHS) Radiation Performance Standard 
according to the Radiation Control for Health and Safety Act of 
1968. This means that the machine does not produce hazard-
ous radiation.
Since radiation emitted inside the machine is completely 
confi ned within protective housings and external covers, the 
laser beam cannot escape from the machine during any phase 
of user operation.
CDRH Regulations
The Center for Devices and Radiological Health (CDRH) of the 
U.S. Food and Drug Administration implemented regulations 
for laser products on August 2, 1976. These regulations apply 
to laser products manufactured from August 1, 1976. Compli-
ance is mandatory for products marketed in the United States.
    CAUTION 
Use of controls, adjustments, or performance of procedures 
other than those specifi  ed in this manual may result in hazard-
ous radiation exposure.
The label is attached to the laser scanner machine inside the 
machine and is not in a user access area.


 
						

							
xviii 
						

							
Chapter
 1
1-1
 This category describes the features of the machine and its useful functions.  
Names and Functions on Each Part of the Machine 1-2
Front Side  1-2
Back Side  1-3
Interior 1-4
Multi-purpose Tray (Manual Feed Slot)  1-5
Paper Cassette  1-6
Operation Panel  1-7
Main Operation Panel  1-7
Fax Operation Panel  1-8
LCD (Standby Mode)  1-9
Copy Mode  1-9
Fax Mode  1-9
Scan Mode  1-9
Text Input Method  1-10
Changing Entry Mode    1-10
Entering Letters and Symbols  1-10
Moving the Cursor (Entering a Space)   1-10
Deleting Characters   1-10
Setting the Sleep Timer  1-11
Setting the Current Date and Time  1-12
    Before Using the Machine   
						

							
1-2
Before Using the Machine
This section describes the parts and functions of the machine.
Front Side
 Names and Functions on Each Part of the Machine 
(1)  Document guides
Adjust to the width of the document.
(2)  Feeder
The feeder can automatically scan documents continuously.
(3)  Operation panel
Controls the machine.
  "Operation Panel" (→
P.1-7) 
(4)  Front cover 
(5)   Multi-purpose tray (manual feed slot)
Use the tray when printing from the tray.
  "Multi-purpose Tray (Manual Feed Slot)" ( →
P.1-5) 
(6)  Paper cassette
Load the paper supply.
  "Paper Cassette" ( →
P.1-6) 
(7)   Document feeder tray
Place document. 
(8)  Tray extension
Pull out the tray extension when the paper is hanging out of the 
document feeder tray such as Legal size paper. 
(9)   Document delivery tray
Documents are output.
(10)  Power switch
Turns the power ON or OFF. 
(11) Ventilation slots 
(12) Speaker
(13) Lift handles
(14)  Scanning area
Scans documents from the feeder. 
(15)  Output tray
Printed paper such as copies, prints and faxes come out from 
the output tray.
(16)  Platen glass
Place document. 
(17)   USB memory port 
Used to save scanned documents in a USB memory.
(18)   Manual feed transport guide 
MF8050Cn
O MF8350Cdn
O
(1)
(7)
(8)
(9)
(10)
(11)
(12)
(13)
(2)
(3)
(4)
(5)
(6)
(14)
(16)
(17)
(18)
(15)
(13)
(1)
(7)
(8)
(13)
(9)
(11)
(12)
(10)
(2)
(3)
(4)
(5)
(6)
(14)
(16)
(17)
(18)
(13)
(15) 
						

							
1-3
Before Using the Machine
Back Side
MF8350Cdn
(1)
(2)(3) (4) (5)
(6)
(7)
(8)
MF8050Cn
(3) (1)
(2)
(4)
(8) (5)
(7)
(6)
O
O
(1)  USB port
Connect the USB cable. 
(2)  LAN port
Connect the LAN cable. 
(3)   Telephone line jack
Connect the telephone cable. 
(4)   External telephone jack
Connect the external telephone. 
(5)  Rear cover
Open this cover when clearing paper jams. 
(6) Rating label
The current value indicated in this rating label shows the 
average power current consumption. 
(7) Ventilation slots 
(8)  Power socket
Connect the power cord.  
						

							
1-4
Before Using the Machine
Interior
MF8350Cdn
(1)
(2)
(3)
(4)
(5)
MF8050Cn
(1)
(2)
(3)
(4)
(5)
O
O
(1)   Y (Yellow) toner cartridge slot
The Y (yellow) toner cartridge is installed in this slot.
(2)  M (Magenta) toner cartridge slot
The M (magenta) toner cartridge is installed in this slot.
(3)  C (Cyan) toner cartridge slot
The C (cyan) toner cartridge is installed in this slot.
(4)  K (Black) toner cartridge slot
The K (black) toner cartridge is installed in this slot.
(5)   Toner cartridge tray
Tray for installing the toner cartridges. 
						

							
1-5
Before Using the Machine
  M ulti-purpose  Tray  (Manual  Feed  Slot)
MF8350Cdn
(1)
(2)
(3)
MF8050Cn
(1)
O
O
(1)  Paper guides
Adjust to the width of the paper. 
(2)   The auxiliary tray (MF8350Cdn Only)
Be sure to pull out this tray when loading paper in the multi-
purpose tray. 
(3)   Tray extension (MF8350Cdn Only)
Open to prevent the paper from hanging out of the multi-
purpose tray when loading long-size paper such as Letter.
  
						

							
1-6
Before Using the Machine
  Pa per  Cassette
MF8350Cdn
(2)
(1) (2)
(3)(1)
MF8050Cn
(2)
(1) (3)
(2)
O
O
(1)   Lock release lever
Hold this lever to slide the paper guides. 
(2)  Paper guide
Adjust the position of the paper guides to the paper. 
(3)   Lock release lever (changing cassette size)
When loading paper that is longer than A4 size, pull out the 
paper cassette while holding this lever.
When the paper cassette is inserted with it extended, the front 
side of the paper cassette is not fl
 ush with the front surface of 
the machine as shown in the fi  gure.
Set the legal dust cover on the paper cassette.