Canon Pixma Ip4850 User Guide

							Advanced Guide > Troubleshooting > Print Results Not Satisfactory > Printed Paper Has Ink Blots or Curls
U316
Printed Paper Curls or Has Ink Blots
 Printed Paper Has Ink Blots
 Printed Paper Curls
Check 1: Did you confirm the paper and print qualit y settings?
Print Results Not Satisfactory
Check 2: If the intensity is set high, reduce the Intensity setting in the
printer driver and try printing again. 
If you are using plain paper to print images with h igh intensity, the paper may absorb too much ink
and become wavy, causing paper abrasion. 
You can confirm the intensity using the printer driver.
Adjusting Intensity
Check 3: Is Photo Paper used for printing photograp hs?
W hen printing data with high color saturation such  as photographs or images in deep color, we
recommend using Photo Paper Plus Glossy II or other  Canon speciality paper.
Loading Paper
Page top
Page 401 of 468 pages
Printed Paper Curls or Has Ink Blots
.ownloadedtfromtManualsPrinterDcomtManuals    
						

							Advanced Guide > Troubleshooting > Print Results Not Satisfactory > Paper Is Smudged/Printed Surface Is Scratched
U317
Paper Is Smudged/Printed Surface Is Scratched
 Paper Is Smudged
The Edges of Paper Are Smudged Printed Surface Is Smudged
 Printed Surface Is Scratched
Check 1: Did you confirm the paper and print quality settings?
Print Results Not Satisfactory
Check 2: Is the appropriate type of paper used? Che ck the followings:
Check to see if the paper you are printing on is suitable for your printing purpose.
Loading Paper
W hen performing Borderless Printing, make sure that  the paper you are using is suitable for
Borderless Printing. 
If the paper you are using is not suitable for Bord erless Printing, the print quality may be
reduced at the top and bottom edges of the paper.
Printing Area
Check 3: Load the paper after correcting its curl.
For Plain Paper 
Turn the paper over and reload it to print on the o ther side.
Leaving the paper loaded on the Rear Tray for a long  time may cause the paper to curl. In this
case, load the paper with the other side facing up.  It may resolve the problem.
W e recommend putting unused paper back into the pac kage and keeping it on a level surface.
For Other Paper 
If the curl on the four corners of the paper is more than 0.1 inch / 3 mm (A) in height, the paper
may be smudged or may not be fed properly. In such  cases, follow the procedure described
below to correct the paper curl. Page 402 of 468 pages
Paper Is Smudged/Printed Surface Is Scratched
.ownloadedtfromtManualsPrinterDcomtManuals     
						

							1.Roll up the paper in the opposite direction to the  paper curl as shown below.
2.Check that the paper is now flat. 
W e recommend printing curl-corrected paper one shee
t at a time.
Note
Depending on the media type, the paper may be smudg ed or may not be fed properly even if it
is not curled inward. In such cases, follow the pro cedure described below to curl the paper
outward within 0.1 inch / 3 mm (B) in height before  printing. This may improve the print result.
(C) Printing side 
W e recommend printing paper that has been curled ou tward one sheet at a time.
Check 4: If you are printing on thick paper, select  the Prevent paper
abrasion setting. 
Selecting the Prevent paper abrasion setting will w iden the clearance between the Print Head and
the loaded paper. If you notice abrasion even with the  media type set correctly to match the loaded
paper, set the printer to prevent paper abrasion on  the computer.
Print speed may be reduced if you are selecting the  Prevent paper abrasion setting.
* Deactivate the Prevent paper abrasion setting onc e printing is complete. If not, this setting remains
enabled for all subsequent print jobs. 
Open the printer driver setup window, and in Custom  Settings in the Maintenance sheet, select the
Prevent paper abrasion check box, and then click Se nd.
To open the printer driver setup window, see 
Opening the Printer Driver Setup W indow.
Check 5: If the intensity is set high, reduce the I ntensity setting in the
printer driver and try printing again. 
If you are using plain paper to print images with h igh intensity, the paper may absorb too much ink
and become wavy, causing paper abrasion. 
Reduce the Intensity setting in the printer driver and  try printing again.
1.Open the printer driver setup window.
Opening the Printer Driver Setup W indow
Click Here: Printer Driver
* Before clicking here to open the printer driver setup window, quit the running application
software. Page 403 of 468 pages
Paper Is Smudged/Printed Surface Is Scratched
.ownloadedtfromtManualsPrinterDcomtManuals     
						

							2.On the Main sheet, select Manual for Color/Intensity, and then click Set.
3.Drag the Intensity slide bar on the Color Adjustment sheet to adjust the intensity.
Check 6: Is printing performed beyond the recommend ed printing area?
If you are printing beyond the recommended printing  area of your printing paper, the lower edge of
the paper may become stained with ink. 
Resize your original document in your application s oftware.
Printing Area
Check 7: Is the Paper Feed Roller dirty? 
Clean the Paper Feed Roller.
Routine Maintenance
Note
Cleaning the Paper Feed Roller will wear the roller, so perform this procedure only when
necessary.
Check 8: Is the inside of the printer dirty? 
W hen performing duplex printing, the inside of the  printer may become stained with ink, causing the
printout to become smudged. 
Perform the Bottom Plate Cleaning to clean the insi de of the printer.
Cleaning Inside the Printer
Note
To prevent the inside of the printer from stains, set th e paper size correctly.
Check 9: Set Ink Drying Wait Time longer. 
Doing so gives the printed surface enough time to dry so that paper smudged and scratched are
prevented.
1.Make sure that the printer is turned on.
2.Open the printer driver setup window.
Opening the Printer Driver Setup W indow
3.
Click the Maintenance tab and then Custom Settings.
4.Drag the Ink Drying Wait Time slide bar to set the  wait time, and then click Send.
5.Confirm the message and click OK.
Check 10: Is the paper scratched by other loaded pa per?
Depending on the media type, the paper may be scrat ched by other loaded paper when feeding from
the Rear Tray. In this case, load one sheet at a time.
Page top
Page 404 of 468 pages
Paper Is Smudged/Printed Surface Is Scratched
.ownloadedtfromtManualsPrinterDcomtManuals 
						

							Advanced Guide > Troubleshooting > Print Results Not Satisfactory > Back of the Paper Is Smudged
U318
Back of the Paper Is Smudged
Check 1: Did you confirm the paper and print quality settings?
Print Results Not Satisfactory
Check 2: Perform the Bottom Plate Cleaning to clean  the inside of the
printer.
Cleaning Inside the Printer
Note
W hen performing borderless printing, duplex printin g, or too much printing, the inside may
become stained with ink.
Page top
Page 405 of 468 pages
Back of the Paper Is Smudged
.ownloadedtfromtManualsPrinterDcomtManuals   
						

							Advanced Guide > Troubleshooting > Print Results Not Satisfactory > Vertical Lines Are Printed on the Sides of thePrintoutU319
Vertical Lines Are Printed on the Sides of the Prin tout
Check 1: Did you confirm the paper type and print quality settings?
Print Results Not Satisfactory
Check 2: Is the size of the loaded paper correct? 
The vertical lines may be printed in the margin if the size of the loaded paper is larger than that yo u
have specified. 
Set the paper size correctly according to the paper you lo aded.
Print Results Not Satisfactory
Note
The direction of the vertical line pattern may vary depending on the image data or the print
setting.
This printer performs automatic cleaning when neces sary to keep printouts clean. A small
amount of ink is ejected for cleaning. 
Although ink is usually ejected on the ink absorber , it may be ejected on the paper if you load
paper larger than that you have specified.
Page top
Page 406 of 468 pages
Vertical Lines Are Printed on the Sides of the Prin tout
.ownloadedtfromtManualsPrinterDcomtManuals   
						

							Advanced Guide > Troubleshooting > Print Results Not Satisfactory > Colors Are Uneven or Streaked
U320
Colors Are Uneven or Streaked
 Colors Are Uneven
 Colors Are Streaked
Check 1: Did you confirm the paper and print quality settings?
Print Results Not Satisfactory
Check 2: Print the Nozzle Check Pattern and perform  any necessary
maintenance operations such as Print Head Cleaning. 
Print the Nozzle Check Pattern to determine whether  the ink ejects properly from the print head
nozzles. 
Refer to 
Routine Maintenance for the Nozzle Check Pattern printing, Print Head C leaning, and Print
Head Deep Cleaning.
If the Nozzle Check Pattern is not printed correctly: 
Check to see if a particular colors ink tank is not empt y.
If the Nozzle Check Pattern is not printed correctly th ough ink is sufficient, perform the Print Head
Cleaning and try printing the Nozzle Check Pattern aga in.
If the problem is not resolved after performing the Print Head Cleaning twice:
Perform the Print Head Deep Cleaning. 
If the problem is not resolved after performing the  Print Head Deep Cleaning, turn off the printer
and perform another Print Head Deep Cleaning after  24 hours.
If the problem is not resolved after performing the Print Head Deep Cleaning twice: Page 407 of 468 pages
Colors Are Uneven or Streaked
.ownloadedtfromtManualsPrinterDcomtManuals     
						

							If Print Head Deep Cleaning does not resolve the problem, the Print Head may be damaged.
Contact the service center.
Check 3: Perform Print Head Alignment.
Routine Maintenance
Note
If the problem is not resolved after performing the  Print Head Alignment, perform Print Head
Alignment manually referring to 
Manual Print Head Alignment.
Page top
Page 408 of 468 pages
Colors Are Uneven or Streaked
.ownloadedtfromtManualsPrinterDcomtManuals 
						

							Advanced Guide > Troubleshooting > Printing Does Not Start
U321
Printing Does Not Start
Check 1: Make sure that the power plug is securely  plugged in, then
turn the printer on. 
W hile the  POWER
 lamp is flashing green, the printer is initializing.  W ait until the POWER
 lamp stops
flashing and remains lit green.
Note
W hen printing large data such as a photo or graphics, it
 may take longer to start printing. W hile
the  POWER
 lamp is flashing green, the computer is processing  data and sending it to the
printer. W ait until printing starts.
Check 2: Check the status of ink tanks. Replace the  ink tank if ink has
run out.
Check 3: Open the Top Cover and check to see if the  ink lamps are
flashing red. 
If there is still sufficient ink but its ink lamp i s flashing red, an ink tank may not be installed in  a right
position.
Routine Maintenance
Check 4: Open the Top Cover and make sure that the  ink lamps light up
red. 
If the ink lamp is not lit, press the 
 mark on the ink tank until it clicks into place.
Check 5: Make sure that the USB cable is securely p lugged in to the
printer and the computer. 
W hen the printer is connected to your computer with  a USB cable, check the followings:
If you are using a relay device such as a USB hub, disconn ect it, connect the printer directly to
the computer, and try printing again. If printing sta rts normally, there is a problem with the relay
device. Consult the reseller of the relay device fo r details.
There could also be a problem with the USB cable. R eplace the USB cable and try printing
again.
Check 6: Restart your computer if you are printing  from the computer.
If there are any unnecessary print jobs, delete the m.
Deleting the Undesired Print Job
Check 7: Make sure that the Inner Cover is closed. 
If the Inner Cover is opened, close the Inner Cover  and press the 
RESUME/CANCEL button on the
printer.
Check 8: Make sure that your printers name is sele cted in the Print
dialog box. 
The printer will not print properly if you are using  a printer driver for a different printer. Page 409 of 468 pages
Printing Does Not Start
.ownloadedtfromtManualsPrinterDcomtManuals  
						

							Make sure that your printers name is selected in the Print dialog box.
Note
To make the printer the one selected by default, se lect Set as Default Printer.
Check 9: Configure the printer port appropriately. 
Make sure that the printer port is configured appropriately.
1.Log on as a user account with administrator privile ge.
2.Select Devices and Printers from the Start menu. 
In W indows Vista, select the Start menu > Control Panel > Hardware and Sound > Printers.
In W indows XP, select the Start menu > Control Panel >  Printers and Other Hardware > Printers
and Faxes.
3.Right-click the Canon XXX icon (where XXX is your  printers name), then select
Printer properties. 
In W indows Vista or W indows XP, right-click the Canon XX X icon (where XXX is your printers
name), then select Properties.
4.Click the Ports tab to confirm the port settings. 
Make sure that a port named USBnnn (where n is a  number) with Canon XXX appearing in the
Printer column is selected for Print to the followi ng port(s).
If the setting is incorrect: 
If the problem is not resolved, reinstall the printer driver.
Printing does not start even though the port named  USBnnn is selected:
Launch Canon My Printer from the task tray, select  Diagnose and Repair Printer. Follow
the on-screen instructions to set the correct printer port,  then select Canon XXX.
If the problem is not resolved, reinstall the print er driver.
Check 10: Is the size of the print data extremely l arge?
Click Print Options on the Page Setup sheet. Then,  select the Prevent loss of print data check box in
the displayed dialog.
Page top
Page 410 of 468 pages
Printing Does Not Start
.ownloadedtfromtManualsPrinterDcomtManuals