Canon Lbp 3200 User Guide

Printing on Envelope2-34
Loading and Delivering Paper
2
8Press down the envelopes as shown in the figure, then make 
sure that they do not exceed the load limit mark and that they 
are loaded under the hooks on the paper guides.
Make sure that there is sufficient space between the hooks and envelopes. Take 
out some envelopes when there is no space.
IMPORTANT
A maximum of approx. 20 envelopes can be loaded in the cassette. Be sure that 
the envelopes do not exceed the load limit mark of the paper guide. If...

Printing on Envelope2-35
Loading and Delivering Paper
2
Setting Envelope in the Manual Feed Slot
Follow the procedure below to set an envelope in the manual feed slot.
When loading paper in the manual feed slot, be sure to load it in portrait orientation.
IMPORTANT
•In the manual feed slot, you can set only one envelope at a time.
•You cannot specify multiple print copies or multiple pages when you use the manual feed 
slot. If you specify multiple print copies or multiple pages using the manual feed...

Printing on Envelope2-36
Loading and Delivering Paper
2
2While holding the envelope with your hands as shown in the 
figure, slowly insert the envelope with the printing surface 
face up until it hits on the back.
After the envelope is set, it is fed slightly.
CAUTION
When setting the envelope, be careful not to cut your hands with the edges 
of the envelope.
IMPORTANT
•Set envelops straight.
•If the envelopes are curled or folded at corners, flatten them before setting.
•The back of an envelope cannot be...

Printing on Envelope2-37
Loading and Delivering Paper
2
Setting Printer Driver and Printing
Follow the procedure below to set the printer driver.
1Select [Print] in the application. Select this printer for [Name] 
and click [Properties].
2Display the [Page Setup] sheet, then from [Page Size], select 
the size of a document that you created in the application.
NOTE
If you select any of [Envelope C5], [Envelope COM10], [Envelope DL], [Envelope 
Monarch] for [Page Size], the appropriate paper type is...

Printing on Envelope2-38
Loading and Delivering Paper
2
3From [Output Size], select the size of the loaded paper as 
needed.
If the size of a document is the same as that of paper set in the cassette or 
manual feed slot, select [Match Page Size].
IMPORTANT
If the settings are different between [Page Size] and [Output Size], the printer 
produces an enlarged or reduced print automatically.
NOTE
If you select any of [Envelope C5], [Envelope COM10], [Envelope DL], [Envelope 
Monarch] for [Output Size], the...

Printing on Envelope2-39
Loading and Delivering Paper
2
5Click [OK] to start printing.
 

Printing on Custom Paper2-40
Loading and Delivering Paper
2
Printing on Custom Paper
This section describes the procedure for printing on custom paper.
Loading Custom Paper
Follow the procedure below to set custom paper. In the manual feed slot, you can 
set custom paper in width of 76.2 to 215.9 mm and in length of 127.0 to 355.6 mm.
The paper source in which you can set custom paper is the manual feed slot only. 
You cannot load custom paper in the cassette.
When loading paper in the manual feed slot,...

Printing on Custom Paper2-41
Loading and Delivering Paper
2
1Insert about 2 cm of the edge of paper into the manual feed 
slot aa a a
, then slide the paper guides aligning with the width of 
the paper bb b b
.
The paper guides move together.
IMPORTANT
•Be sure to align the paper guides with the width of the paper. If the paper guides 
are too loose or too tight, this may result in misfeeds or paper jams.
2While holding paper with your hands as shown in the figure, 
insert paper with the printing surface...

Printing on Custom Paper2-42
Loading and Delivering Paper
2
CAUTION
When setting paper, be careful not to cut your hands with the edges of the 
paper.
IMPORTANT
•Set the paper straight.
•If the paper is curled or folded at corners, flatten it before loading.
NOTE
To print on letterhead paper or paper printed with a logo, set the paper so that the 
printing surface faces up and the top edge comes toward the back of the manual 
feed slot.
:Feeding direction
 

Printing on Custom Paper2-43
Loading and Delivering Paper
2
Setting Printer Driver and Printing
Follow the procedure below to set the printer driver.
1Select [Print] in the application. Select this printer for [Name] 
and click [Properties].
2Display the [Page Setup] sheet, then from [Page Size], select 
the size of a document that you created in the application.
NOTE
In order to use the custom paper, you have to register the custom paper size in 
advance. For instructions on registering the custom paper...