Canon Lbp 3000 User Guide

Printing on Custom Paper Sizes (Non-Standard Sizes)2-52
Loading and Delivering Paper
2
1Push the side paper guides out a little wider than the actual 
width of the paper.
2Gently load the paper with the printing side facing up until it 
touches the back of the tray.
Make sure that the paper passes under the paper limit guides.
CAUTION
When loading paper, take care not to cut your hands with the edges of the 
paper.
IMPORTANT
•Load the paper so that it is straight.
•If the paper is curled or folded at the...

Printing on Custom Paper Sizes (Non-Standard Sizes)2-53
Loading and Delivering Paper
2
NOTE
To print on letterhead paper or paper with a logo already printed on it, load the 
paper so that the printed side is facing up and the top of the paper is at the far end.
3Slide the paper guides to fit both sides of the paper.
 

Printing on Custom Paper Sizes (Non-Standard Sizes)2-54
Loading and Delivering Paper
2
IMPORTANT
•If you run out of paper and then refill the paper tray, the Paper Indicator will flash. 
Press the   (Paper Key) to resume printing.
•Always make sure the paper guides match the width of the paper. If the paper 
guides are too loose or too tight, the paper will not feed properly and this will cause 
paper jams.
Selecting Printer Driver Settings and Printing
This section describes how to set the printer driver...

Printing on Custom Paper Sizes (Non-Standard Sizes)2-55
Loading and Delivering Paper
2
2Display the [Page Setup] sheet, then set the [Page Size] 
setting to the size of the document that you created in the 
application.
NOTE
•When you are using a custom paper size, you need to register the size of the 
custom paper in advance. Refer to Specifying a Custom Paper Size 
(Non-Standard Paper), on p. 4-39 for information on how to register a custom 
paper size.
•When you set the page size to [Index Card], the...

Printing on Custom Paper Sizes (Non-Standard Sizes)2-56
Loading and Delivering Paper
2
3Set the [Output Size] setting to the name (paper size) of the 
custom paper loaded in the printer as needed.
Leave the setting set to [Match Page Size] when the page size and the size of 
the paper loaded in the multi-purpose tray (the name of the custom paper size) 
are the same, since there is no need to change the setting.
IMPORTANT
If the [Page Size] and [Output Size] settings are different, the printer produces...

Printing on Custom Paper Sizes (Non-Standard Sizes)2-57
Loading and Delivering Paper
2
5Click [OK] to start printing.
 

Printing on Custom Paper Sizes (Non-Standard Sizes)2-58
Loading and Delivering Paper
2
 

CHAPTER
2-1
2Loading and Delivering Paper
This chapter describes the types of paper that can be used with this printer, and how the paper 
is loaded and delivered.
Paper Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-2
Usable Paper . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-2
Printable Area . . . . . . . . . . . . . . . . . . . . . . . . . . . . ....

Introduction3-2
Setting Up the Printing Environment
3
Introduction
After Installing the Printer
The following shows the tasks that should be performed after installing the printer:
■Installing the Printer Driver (See p. 3-4)
The printer driver is a piece of software that is needed when you are printing from 
application software. Settings related to printing can be configured using the printer driver.
■Using a computer to share the printer on a network (See p. 3-47)
If you share this printer on a network...

Introduction3-3
Setting Up the Printing Environment
3
•Microsoft Windows Vista*
*32-bit processor version only
-System Requirements (minimum required)
(PC/AT Compatibles)
*1As the amount of available memory varies depending on the system configuration of the computer or 
application you are using, the above environment does not guarantee printing in all cases.
*
2This indicates free hard disk space required for installing the printer driver and manuals using Easy 
Installation. Required free hard disk...